Philips VR810BPH owner manual Hookups without a Cable Box cont’d, Antenna Or Cable

Page 7

Hookups without a Cable Box (cont’d) 7

3

Connect the RF coaxial cable (supplied) to the TV OUT Jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on type or screw-on type of coaxial cable, whichever you prefer. A snap-on type is sup- plied.)

Antenna

or Cable

4

				LP 20917-003
VIDEO		OUT	IN	VHF/UHF
	(MONO)			ANTENNA IN
L
AUDIO		S VIDEO		CABLE BOX
R				CH3 CH4
				TV OUT
OUT	IN

	LP 20917-003
	VHF/UHF
CH3	CH4
	TV OUT

	75Ω
ANT		/
C	AB
	LE

RF coaxial cable	Antenna In Jack
RF coaxial cable	(on back of TV)
	example only

Plug in the TV and the VCR.

5

Set the CH3/CH4 switch on the back of the VCR to CH3 or CH4, whichever channel is not used or least used in your area. To operate your VCR with your TV, set the TV to the same channel. For example, when playing a tape, if the CH3/CH4 switch is set to CH3, the TV should be on channel 3.

H	4
C
or	3
H	3
C

CH3 / CH4

Switch

CH3 CH4

6

VIDEO	OUT IN
	(MONO)

L

S VIDEO

AUDIO

R

OUT IN

LP 20917-003

VHF/UHF

ANTENNA IN

CH3 CH4

TV OUT

LP 20917-003

ANTENNA

CABLE BOX

CH3 CH4

TV

You are ready to turn on the VCR. Please go to pages 10-11 before turning on the VCR.

Image 7

Contents VR810BPH For Customer Use Dear Philips product ownerPicture Quality FeaturesSafety Precautions IntroductionTable of Contents VCR Maintenance/Video Head Cleaning Before Using Your VCRPutting Batteries in the Remote Control Using the Remote ControlDisconnect the antenna or cable from your TV Hookups without a Cable BoxAntenna Or Cable Hookups without a Cable Box cont’dRecording/Viewing Any Channel Cable signal RF coaxial cableHookups with a Cable Box/Direct Broadcast System ConnectionsTV’s Recording One Channel/Watching AnotherWith this connection 2RF coaxial cableMenu shown below will appear Turning on Your VCRTurn on the TV Turning on Your VCR cont’d Press the VCR button, then press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dSelected channel To make corrections, follow steps Setting the ClockManual Clock Setting Channels are set up. Details are onSetting the Clock cont’d Time Zone Selection Setting the Clock cont’dManual PBS Channel Selection Automatic PBS Channel Selection Daylight-Savings Time CBL/DBS VCR VCR/TV PowerPress the Play 8 or Stop 9 button to select LAN Language SelectionPress the Menu button Line Input Mode Remaining Tape Time Indicator VCR Display Panel VHS Indicator VR1010BP onlyTape Speed Timer Light Lights Turbo Timer indicatorsFront Panel Rear Panel Remote Control Buttons ALTernate Channel Turbo Timer ButtonTimer Button SAT/CBL/DBS ButtonRepeat step Setting the Remote Control to Operate a TVFind the code for your Turn on your Satellite Receiver/Cable Box/DBSPress the Play 8 or Stop 9 button to select on If on Screen Mode is set to on orRead and follow the steps below to play a tape Playback options and features are on pagesWhen you insert a tape, tape manag PlayingAppear on the display panel VCR records in a preset volumeRecording Press the VCR buttonVHS Recording VR1010BP only VHS ET VR1010BP only VCR light will disappear from the display panel Recording One Channel/Watching AnotherOne-Touch Recording Channels are set up. Details are on pagesStarting an OTR Record Link Channels Setting Up the VCR Plus+ Programming SystemCall Letters 2on Examine the listsTimer Recording with the VCR Plus+ Programming System If you forget to turn off the VCR To check your timer recordings, seeChannels are programmed. Details are on pages Quick ProgrammingTape Speeds Instructions continue onQuick Programming cont’d Helpful Hint Current channel number will appear on the display panel. To Turbo Timer1Insert a tape into the VCR Indicates a Daily recording Checking, Editing, or Clearing Timer RecordingsProgram Review Indicates a Weekly recordingInformation about the chosen program will appear Or, to cancel the timer recording, press the Clear buttonProgram Overlap Warning Press the OK/STATUS button to select the programFollow the steps below to set Timer REC Speed to Auto Timer Recording Speed SettingVCR 1 will play your tape. Insert a prerecorded tape in VCR Rerecording Tape DuplicationMake sure the video tape’s record tab is intact Audio cableBlinks and appears on the VCR display panel Audio equipment CD player etcConnect the Cable signal to Connecting the ControllerCable Box/DBS Controller Connect the Controller Make sure the clock is set. You must set the clock manually Setting the Controller to Operate a Cable BoxWait for a few seconds Setting the Controller to Operate a Cable Box cont’dChannel other than Setting the Controller to Operate a DBSWill learn your DBS code 7Wait for a few seconds Setting the Controller to Operate a DBS cont’dReceiving a Stereo Broadcast Multi-Channel Television Sound SystemReceiving a Second Audio Program Record the program as usual. Details are on Multi-Channel Television Sound System cont’dHi-Fi Stereo Tape Playback Or special effects playback Video StabilizerSmartPicture To provide the highest possible picture quality Digital Studio Picture ControlTo set Dspc to on or OFF, follow these steps Skip Search Press the Stop 9 button to cancel a Skip SearchSearch Options Index SearchViewing a Slow Motion Picture Playback OptionsForward and Reverse Searching Viewing a Still PictureWill light Viewing a Picture in Slow to Fast MotionPress the VCR button, then press the Tape Tape ManagerFind a Title Insert a tape that was recorded with this VCRCheck Memory screen appears Tape Manager cont’dCheck Memory Press the Play 8 or Stop 9 button to select CheckIf you don’t see the tape title or pro Edit TitleTape titles may have up to 10 characters Selected program Entering CharactersFootball Sorting by Tape NumberSorting by Date As follows, for example Sorting by CategoryReview the tape portion to make sure it is blank Find Blank SpaceIf you want to erase more information, repeat steps Deleting Tape or Program InformationYou can disable the Tape Manager if you don’t want to use it CL will disappear from the display panel When Child Lock is activatedChild Lock CL will blink intermittently on the display panelTo set Blue Background to on or OFF, follow these steps Blue BackgroundAutomatic Operation Features Glossary Helpful Hints Helpful Hints cont’d Video Cassette Recorder or Player Limited WarrantyCheck or money order Account number Limited Warranty cont’dTo obtain a replacement product from Philips Payment AmountSpecifications Cable box Remote controlTimer AutomaticSupplied Accessories