Baby Einstein 30886 manual Install the batteries in the vibration unit, Hook-and-loop strap

Page 3

ALocate the seat pad and place it upside down on a firm surface.

BUnbuckle the straps on each side of the seat pad.

CUnfasten the hook-and- loop strap and fold back the two fabric flaps.

Hook-and-loop strap

D Hold the seat pad above

the seat frame. Turn the

seat pad so that opening

for the vibration unit is

at the front of the frame

(footrest).

Straps with buckles

Fabric flaps

Fabric pocket in seat pad

5

Install the batteries in the vibration unit.

The vibration unit requires (3) size C (1.5V) batteries (not included). Please use alkaline batteries for better performance.

CAUTION: Follow the battery guidelines in this section. Otherwise, battery life may be shortened or the batteries may leak or rupture.

•Always keep batteries away from children. • Do not mix old and new batteries. • Do not mix alkaline, standard or rechargeable batteries. • Only batteries of the same or equivalent type as recommended are to be used. • Install the batteries so that the polarity of each one matches the markings in the battery compartment. • Do not short-circuit the batteries. • Do not store batteries in areas that have extreme temperatures (such as attics, garages, or automo- biles). • Remove exhausted batteries from the battery compartment. • Never attempt to recharge a battery unless it is specifically marked “rechargeable.” • Rechargeable batteries are to be removed from the toy before being charged. • Rechargeable batteries are only to be charged under adult supervision. • Do not use rechargeable alkaline batteries in a Ni-Cad or Ni-MH battery charger.

E

Open the pocket at the

 

top edge of the seat pad

 

and slide it over the

 

backrest frame.

F

Lift up the two fabric

 

flaps (shown below).

 

Slide the two flaps over

 

and under the footrest

 

wire.

Opening in seat pad

AUse a Phillips screwdriver to loosen the screw that secures the battery compartment cover. A retentive washer keeps the screw from falling off the cover.

BTemporarily remove the cover by disengaging the

2 tabs at the side opposite the screw.

CInstall the batteries...

•(If you are replacing batteries, remove the old ones first.)

Phillips screwdriver

Battery

cover

Vibration unit

Fabric flaps lifted

Fabric flaps under footrest wire frame

•Install (3) size C (1.5 V)

batteries, observing the polarity markings embossed on the bottom of the compartment.

•Install each battery by first tilting it so that the negative (–) end goes in first, pushing slightly against the coil spring contact. The positive (+) end of each battery goes in last.

G Gently tilt the bouncer

Straps fastened

backward until the

 

backrest contacts the floor.

 

H Fasten (buckle) the straps together on each side, securing the seat pad to the frame.

NOTE: Do not fasten the hoop-and-loop patches yet. That step will occur after the vibration unit installation.

CorrectIncorrect

DReplace the battery cover and tighten the screw. Do not overtighten.

– 3 –

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Assembly Instructions Safety Guidelines to Prevent InjuryConnect the wire uprights to the base frame wire CorrectIncorrect Assemble the seat frameConnect the seat frame to the base frame Attach the seat pad to the seat frameOpening in seat pad Install the batteries in the vibration unitHook-and-loop strap Straps with buckles Fabric flaps Fabric pocket in seat padMount the toy bar to the bouncer frame Install the vibration unitOperating Instructions Using the Seat RestraintUsing the Vibration Function Using the Toy Bar FunctionsSong List Care and CleaningParts List and Drawing Changing the BatteriesInstrucciones para armar Pautas de seguridad para prevenir lesionesConecte el cable vertical en la base del armazón de cables Receptáculos apuntando Hacia arriba Conecte el armazón del asiento al armazón de la baseEnsamblaje el armazón del asiento Coloque la almohadilla del asiento en el armazónInstale la batería en la unidad vibratoria Unidad de vibración Instale la unidad de vibraciónMonte la barra de juguetes en el armazón del saltador Abertura en la almohadilla Del asiento ConectorUso de las funciones de la Barra de juguetes Instrucciones de funcionamientoUtilización del sujetador del asiento Utilización de la función de vibraciónLista de canciones Cambio de bateríasCuidado y limpieza Lista de partes y dibujoToujours poser sur le sol Instructions d’assemblageDirectives de sécurité pout éviter les blessures Un mouvement de l’enfant peut faire glisser le relaxFixer le cadre du dossier sur le cadre de base Assembler le cadre du relaxPoser le coussin de l’assise sur le cadre du siège Installer les piles dans le module vibrations Installer le module vibrations Monter la barre de jouets sur le cadre du relaxOuverture du coussin de l’assise Prise Utiliser les fonctions de la barre de jouets Mode d’emploiUtilisation des sangles de sécurité du siège Utilisation de la fonction vibrationsListe de chansons Remplacement des pilesEntretien et nettoyage Liste de pièces et dessin

30886 specifications

The Baby Einstein 30886 is a premier educational toy designed to stimulate infants' cognitive development through engaging and interactive features. This vibrant activity center encourages sensory discovery, making it an essential addition to your baby's early learning environment.

One of the standout features of the Baby Einstein 30886 is its innovative touch and feel technology. The toy is equipped with various textures that provide tactile stimulation, allowing babies to explore different materials while promoting sensory awareness. This aspect is crucial for developing fine motor skills as infants learn to grasp and manipulate objects.

The Baby Einstein 30886 also showcases an array of lights and sounds, captivating infants' attention and enhancing their auditory and visual perception. The lights flash rhythmically in sync with music, creating an engaging atmosphere that encourages your baby to respond through movement and interaction. Each press of a button yields cheerful melodies and playful sounds, fostering auditory learning and memory retention.

Furthermore, the product features multilingual content, introducing babies to basic words and concepts in multiple languages, such as English, Spanish, and French. This aspect not only enriches their vocabulary but also lays the groundwork for future language acquisition, making it an excellent learning tool for parents keen on early bilingual education.

Durability is another critical characteristic of the Baby Einstein 30886. Made from high-quality, non-toxic materials, this toy is designed to withstand the rigors of everyday play. Parents can have peace of mind knowing that it is safe for their little ones to explore, chew, and engage with.

The compact and lightweight design of the Baby Einstein 30886 makes it easily portable, allowing parents to take it along on family outings or trips. Its easy-to-clean surface is an added benefit, making maintenance simple and hassle-free.

In summary, the Baby Einstein 30886 is an exemplary educational toy equipped with tactile features, vibrant lights and sounds, multilingual learning opportunities, and a focus on durability and portability. It not only provides endless entertainment but also significantly contributes to infants' cognitive development and sensory exploration, making it a must-have for modern parents dedicated to enriching their child’s early experiences.
Top Page Image Contents