Denon AVR-5700 manual Select the desired unit, meters or feet

Page 21

2

Switch to the Delay Time screen.

ENTER

3

Select the desired unit, meters or feet.

 

 

Select (darken) the desired units, “Meters” or “Feet”.

Example: When “Feet” is selected

4

Once “Meters” or “Feet” is selected in step 3, the Delay Time screen appears automatically.

5

6

Select the speaker to be set.

Set the distance between the center speaker and listening position.

The distance changes in units of 0.1 meters (1 foot) each time the button is pressed. Select the value closest to the measured distance.

Example: When the distance is set to 12 feet for the center speaker (L1)

2If “Yes” is selected for “Default”, the settings are

automatically reset to the default values.

Please note that the difference of distance for every speaker should be 15 ft (4.5 m) or less. If you set an invalid distance, a CAUTION notice, such as screen right will appear. In this case, please relocate the blinking speaker(s) so that its distance is no larger than the value shown in highlighted line.

21

Image 21
Contents AVR-5700 Safety Precautions Safety Instructions Before Using Table of ContentsFeatures Connections Connecting the audio componentsConnecting video components Precaution when using S-jacks Connecting a video component equipped with S-Video jacksConnecting a monitor TV Connecting the video decksConnecting the antenna terminals AM loop antenna assemblyConnection of AM antennas Connecting a monitor TV Monitor OUT jack Connecting a DVD player DVD in jacksConnecting the Multi Source jacks Connecting the external input EXT. in jacksSpeaker system connections Connecting the speaker cordsSpeaker Impedance ConnectionsProtector circuit Front Panel Part Names and FunctionsPower button …………………………36 Tuner buttons …………………………52 Remote control unitSystem Setup button Setting UP the SystemSurround Parameter button Enter buttonSurround speaker selector function Setting the type of speakers Before setting up the systemEnter the setting Setting the bass outputSystem Setup Menu reappears At the System Setup Menu select Bass OutputSubwoofer Only THX recommended THX mode Setting the delay timeAt the System Setup Menu select Delay Time Front & SubwooferSelect darken the desired units, Meters or Feet Select the desired unit, meters or feetSetting the channel level Test tone A, B or A+BSurr. Sp. a Volume can be adjusted between -12 dB and +12 dB in units When the Manual mode is selectedChannel Level screen reappears AVR-5700 automatically sets the subwoofer peak limit level Subwoofer peak limit level settingSetting the digital inputs Auto tuner presets Setting the on-screen display OSDOn-screen display signals After completing system setupRemote Control Unit Using the remote control unitInserting the batteries Operated. The tuner can be operated when the switch is at Set mode switch 2 to the position for the component to beOperating Denon audio components Any position but LockPreset memory VCR Set the slide switch to the component to be registered VDP Operating a video component stored in the preset memoryVCR or TV Operate the video componentLearning function Using the system call function System call functionSystem call buttons Clearing system call settings Storing signalsBefore operating OperationInput mode selection function Select the input mode Selecting the analog modePlaying the input source Select the input source to be playedManual Auto mode Digital Auto mode Digital PCM mode Select the play modeAdjust the volume Input mode when playing DTS sourcesListening over headphones Adjusting the sound quality toneAfter starting playback Turning the sound off temporarily mutingMulti-source recording/playback Playing one source while recording another REC OUT modePlayback using the external input EXT. in jacks Multi Room Music Entertainment System Multi-source and multi-zone playbackAdjust the level of the selected speaker SurroundBefore playing with the surround function Fader function Dolby Surround Pro Logic modeSet the input mode to Auto or Digital Set the input mode to Auto or RFSelect the Dolby Surround mode DTS indicator lights when playing DTS sourcesCOMP. Dynamic Range Compression Surround parameters Cinema EQ. Cinema EqualizerLFE Low Frequency Effect Dialogue NormalizationHome THX Cinema mode Surround modes and their features DSP Surround SimulationPersonal Memory Plus Select the surround mode for the input channel DSP surround simulationWide Screen can only be selected from the main unit Select Tone Tone control settingSurround modes and parameters Surround parametersAuto tuning Manual tuningListening to the Radio Checking the preset stations Recalling preset stations Last Function MemoryInitialization of the Microprocessor Troubleshooting Additional Information Types of multi-channel signalsOptimum surround sound for different sources Types of sources Movie audioSpeaker setting examples Basic setting for primarily watching moviesWhen using different surround speakers for movies and music Dolby Surround Dolby Digital Dolby Surround AC-3 Surround2Dolby Digital and Dolby Pro Logic Dolby Digital compatible media and playback methodsDTS Digital Surround Dolby Pro LogicDTS compatible media and playback methods Re-equalizer Home THX Cinema surround modeTimber matching circuit Dynamic decorrelation circuitAUX TAPE-1 Surround modes and parametersAudio section Power amplifier Rated output SpecificationsPage 14-14, Akasaka 4-CHOME, MINATO-KU, Tokyo 107-8011, Japan