Denon AVR-5700 manual Table of Contents, Before Using

Page 4

2INTRODUCTION

Thank you for choosing the DENON AVR-5700 Digital Surround A / V receiver. This remarkable component has been engineered to provide superb surround sound listening with home theater sources such as DVD, as well as providing outstanding high fidelity reproduction of your favorite music sources.

As this product is provided with an immense array of features, we recommend that before you begin hookup and operation that you review the contents of this manual before proceeding.

TABLE OF CONTENTS

1

2

3

4

5

6

7

8

9

Before Using ……………………………………………………………………4

10

Surround ……………………………………………………………………43~47

Cautions on Installation …………………………………………………………4

11

DSP Surround Simulation …………………………………………………48~51

Cautions on Handling ……………………………………………………………5

12

Listening to the Radio ……………………………………………………52~54

Features …………………………………………………………………………5

13

Last Function Memory…………………………………………………………54

Connections …………………………………………………………………6~13

14

Initialization of the Microprocessor …………………………………………54

Part Names and Functions ………………………………………………14, 15

15

Troubleshooting ………………………………………………………………55

Setting up the system ……………………………………………………16~27

16

Additional Information ……………………………………………………56~61

Remote Control Unit ………………………………………………………28~36

17

Specifications …………………………………………………………………62

Operation …………………………………………………………………36~42

 

 

2ACCESSORIES

Check that the following parts are included in addition to the main unit:

Q Operating instructions…..1

W Warranty ( for North America model only )………...........1

E Service station list…….....1

R AC cord.................……1

T Remote control unit

Y R6P/AA batteries….....2

U AM loop antenna…...1

I FM indoor antenna…........1

O FM antenna adaptor….1

(RC-853)………………… ..1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 BEFORE USING

Pay attention to the following before using this unit:

•Moving the set

To prevent short circuits or damaged wires in the connection cords, always unplug the power cord and disconnect the connection cords between all other audio components when moving the set.

•Before turning the power switch on

Check once again that all connections are proper and that there are not problems with the connection cords. Always set the power switch to the standby position before connecting and disconnecting connection cords.

2 CAUTIONS ON INSTALLATION

Noise or disturbance of the picture may be generated if this unit or any other electronic equipment using microprocessors is used near a tuner or TV.

If this happens, take the following steps:

•Install this unit as far as possible from the tuner or TV.

•Set the antenna wires from the tuner or TV away from this unit’s power cord and input/output connection cords.

•Noise or disturbance tends to occur particularly when using indoor antennas or 300 Ω /ohms feeder wires. We recommend using outdoor antennas and 75 Ω /ohms coaxial cables.

For heat dispersal, leave at least 10 cm of space between the top, back and sides of this unit and the wall or other components.

•Store this instructions in a safe place.

After reading, store this instructions along with the warranty in a safe place.

•Note that the illustrations in this instructions may differ from the actual set for explanation purposes.

 

2 10 cm or more

2

2

10 cm or more

10 cm or more

Wall

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents AVR-5700 Safety Precautions Safety Instructions Table of Contents Before UsingFeatures Connecting the audio components ConnectionsConnecting video components Connecting a video component equipped with S-Video jacks Precaution when using S-jacksConnecting a monitor TV Connecting the video decksAM loop antenna assembly Connecting the antenna terminalsConnection of AM antennas Connecting a DVD player DVD in jacks Connecting a monitor TV Monitor OUT jackConnecting the external input EXT. in jacks Connecting the Multi Source jacksConnecting the speaker cords Speaker system connectionsSpeaker Impedance ConnectionsProtector circuit Part Names and Functions Front PanelRemote control unit Power button …………………………36 Tuner buttons …………………………52Setting UP the System System Setup buttonSurround Parameter button Enter buttonSurround speaker selector function Before setting up the system Setting the type of speakersSetting the bass output Enter the settingSystem Setup Menu reappears At the System Setup Menu select Bass OutputSetting the delay time Subwoofer Only THX recommended THX modeAt the System Setup Menu select Delay Time Front & SubwooferSelect the desired unit, meters or feet Select darken the desired units, Meters or FeetTest tone A, B or A+B Setting the channel levelSurr. Sp. a When the Manual mode is selected Volume can be adjusted between -12 dB and +12 dB in unitsChannel Level screen reappears Subwoofer peak limit level setting AVR-5700 automatically sets the subwoofer peak limit levelSetting the digital inputs Setting the on-screen display OSD Auto tuner presetsAfter completing system setup On-screen display signalsUsing the remote control unit Remote Control UnitInserting the batteries Set mode switch 2 to the position for the component to be Operated. The tuner can be operated when the switch is atOperating Denon audio components Any position but LockPreset memory VCR Operating a video component stored in the preset memory Set the slide switch to the component to be registered VDPVCR or TV Operate the video componentLearning function System call function Using the system call functionSystem call buttons Storing signals Clearing system call settingsOperation Before operatingSelect the input mode Selecting the analog mode Input mode selection functionPlaying the input source Select the input source to be playedSelect the play mode Manual Auto mode Digital Auto mode Digital PCM modeAdjust the volume Input mode when playing DTS sourcesAdjusting the sound quality tone Listening over headphonesAfter starting playback Turning the sound off temporarily mutingPlaying one source while recording another REC OUT mode Multi-source recording/playbackPlayback using the external input EXT. in jacks Multi-source and multi-zone playback Multi Room Music Entertainment SystemSurround Adjust the level of the selected speakerBefore playing with the surround function Dolby Surround Pro Logic mode Fader functionSet the input mode to Auto or RF Set the input mode to Auto or DigitalSelect the Dolby Surround mode DTS indicator lights when playing DTS sourcesSurround parameters Cinema EQ. Cinema Equalizer COMP. Dynamic Range CompressionLFE Low Frequency Effect Dialogue NormalizationHome THX Cinema mode DSP Surround Simulation Surround modes and their featuresPersonal Memory Plus DSP surround simulation Select the surround mode for the input channelWide Screen can only be selected from the main unit Tone control setting Select ToneSurround parameters Surround modes and parametersManual tuning Auto tuningListening to the Radio Checking the preset stations Last Function Memory Recalling preset stationsInitialization of the Microprocessor Troubleshooting Types of multi-channel signals Additional InformationOptimum surround sound for different sources Types of sources Movie audioBasic setting for primarily watching movies Speaker setting examplesWhen using different surround speakers for movies and music Surround Dolby Surround Dolby Digital Dolby Surround AC-32Dolby Digital and Dolby Pro Logic Dolby Digital compatible media and playback methodsDolby Pro Logic DTS Digital SurroundDTS compatible media and playback methods Home THX Cinema surround mode Re-equalizerTimber matching circuit Dynamic decorrelation circuitSurround modes and parameters AUX TAPE-1Specifications Audio section Power amplifier Rated outputPage 14-14, Akasaka 4-CHOME, MINATO-KU, Tokyo 107-8011, Japan
Top Page Image Contents