Denon AVR-5700 manual Volume can be adjusted between -12 dB and +12 dB in units

Page 23

6

7

8

Select “Test Tone Start”.

Select “Yes”.

a.If the “Auto” mode is selected:

Test tones are automatically emitted from the different speakers.

The test tones are emitted from the different speakers in the following order, at 4-second intervals the first time and second time around, 2-second intervals the third time around and on:

 

1

FL

1

C

1

FR

1

SR

1

SL

1

SW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Use the CURSOR buttons to adjust all the speakers to the same

volume.

 

 

 

Flashing

The volume can be adjusted between –12 dB and +12 dB in units of

1 dB.

 

 

 

Example: When the volume is set to –12 dB

 

 

 

 

while the test tone is being

 

 

 

 

produced from the subwoofer

b. When the “Manual” mode is selected

 

Flashing

 

 

 

 

 

 

 

 

Use the

and

cursor buttons to select the speaker from which

 

 

 

 

you want to produce the test tone, then use the

and

cursor

 

 

 

 

 

 

buttons to adjust so that the volume from the different speakers sounds the same.

Example: When the volume is set to –12 dB while the subwoofer is selected

9

 

After the above settings are completed, press the ENTER button again.

ENTER

The “Channel Level” screen reappears.

 

2To cancel the settings, select “Level Clear” and “Yes” on the “Channel Level” screen, then make the settings again.

The level of each channel should be adjusted to 75 dB (C-weighted, slow meter mode) on a sound level meter at the listening position.

If a sound level meter is not available adjust the channels by ear so the sound levels are the same. Because adjusting the subwoofer level test tone by ear is difficult, use a well known music selection and adjust for natural balance.

NOTE: When adjusting the level of an active subwoofer system, you may also need to adjust the subwoofer’s own volume control.

2When you adjust the channel levels while in the SYSTEM SETUP CHANNEL LEVEL mode, the channel level adjustments made will affect ALL surround modes. Consider this mode a Master Channel Level adjustment mode.

2After you have completed the SYSTEM SETUP CHANNEL LEVEL adjustments, you can then activate the individual surround modes and adjust channel levels that will be remembered for each of those modes. Then, whenever you activate a particular surround sound mode, your preferred channel level adjustments for just that mode will be recalled. Check the instructions for adjusting channel levels within each surround mode on Page 43.

2You can adjust the channel levels for each of the following surround modes: DIRECT, STEREO, 5 CH STEREO, DOLBY/DTS SURROUND, HOME THX CINEMA, WIDE SCREEN, SUPER STADIUM, ROCK ARENA, JAZZ CLUB, CLASSIC CONCERT, MONO MOVIE, and MATRIX.

2When using either surround speakers A or B, or when using surround speakers A and B at the same time, be sure to adjust the balance of playback levels between each channel for the various selections of “A or B” and “A and B”.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents AVR-5700 Safety Precautions Safety Instructions Before Using Table of ContentsFeatures Connections Connecting the audio componentsConnecting video components Connecting the video decks Connecting a video component equipped with S-Video jacksPrecaution when using S-jacks Connecting a monitor TVConnection of AM antennas Connecting the antenna terminalsAM loop antenna assembly Connecting a monitor TV Monitor OUT jack Connecting a DVD player DVD in jacksConnecting the Multi Source jacks Connecting the external input EXT. in jacksConnections Connecting the speaker cordsSpeaker system connections Speaker ImpedanceProtector circuit Front Panel Part Names and FunctionsPower button …………………………36 Tuner buttons …………………………52 Remote control unitEnter button Setting UP the SystemSystem Setup button Surround Parameter buttonSurround speaker selector function Setting the type of speakers Before setting up the systemAt the System Setup Menu select Bass Output Setting the bass outputEnter the setting System Setup Menu reappearsFront & Subwoofer Setting the delay timeSubwoofer Only THX recommended THX mode At the System Setup Menu select Delay TimeSelect darken the desired units, Meters or Feet Select the desired unit, meters or feetSurr. Sp. a Setting the channel levelTest tone A, B or A+B Channel Level screen reappears Volume can be adjusted between -12 dB and +12 dB in unitsWhen the Manual mode is selected AVR-5700 automatically sets the subwoofer peak limit level Subwoofer peak limit level settingSetting the digital inputs Auto tuner presets Setting the on-screen display OSDOn-screen display signals After completing system setupInserting the batteries Remote Control UnitUsing the remote control unit Any position but Lock Set mode switch 2 to the position for the component to beOperated. The tuner can be operated when the switch is at Operating Denon audio componentsPreset memory VCR Operate the video component Operating a video component stored in the preset memorySet the slide switch to the component to be registered VDP VCR or TVLearning function System call buttons Using the system call functionSystem call function Clearing system call settings Storing signalsBefore operating OperationSelect the input source to be played Select the input mode Selecting the analog modeInput mode selection function Playing the input sourceInput mode when playing DTS sources Select the play modeManual Auto mode Digital Auto mode Digital PCM mode Adjust the volumeTurning the sound off temporarily muting Adjusting the sound quality toneListening over headphones After starting playbackMulti-source recording/playback Playing one source while recording another REC OUT modePlayback using the external input EXT. in jacks Multi Room Music Entertainment System Multi-source and multi-zone playbackBefore playing with the surround function Adjust the level of the selected speakerSurround Fader function Dolby Surround Pro Logic modeDTS indicator lights when playing DTS sources Set the input mode to Auto or RFSet the input mode to Auto or Digital Select the Dolby Surround modeDialogue Normalization Surround parameters Cinema EQ. Cinema EqualizerCOMP. Dynamic Range Compression LFE Low Frequency EffectHome THX Cinema mode Personal Memory Plus Surround modes and their featuresDSP Surround Simulation Wide Screen can only be selected from the main unit Select the surround mode for the input channelDSP surround simulation Select Tone Tone control settingSurround modes and parameters Surround parametersListening to the Radio Auto tuningManual tuning Checking the preset stations Initialization of the Microprocessor Recalling preset stationsLast Function Memory Troubleshooting Types of sources Movie audio Types of multi-channel signalsAdditional Information Optimum surround sound for different sourcesWhen using different surround speakers for movies and music Speaker setting examplesBasic setting for primarily watching movies Dolby Digital compatible media and playback methods SurroundDolby Surround Dolby Digital Dolby Surround AC-3 2Dolby Digital and Dolby Pro LogicDTS compatible media and playback methods DTS Digital SurroundDolby Pro Logic Dynamic decorrelation circuit Home THX Cinema surround modeRe-equalizer Timber matching circuitAUX TAPE-1 Surround modes and parametersAudio section Power amplifier Rated output SpecificationsPage 14-14, Akasaka 4-CHOME, MINATO-KU, Tokyo 107-8011, Japan
Top Page Image Contents