Denon AVR-5700 manual Preset memory

Page 30

Preset memory

•DENON and other makes of components can be operated by setting the preset memory for your make of video component. Operation is not possible for some models, however. In this case use the learning function (see page 33) to store the remote control signals.

•For instructions on clearing the presettings stored in the preset memory, see page 36.

1

Set the slide switch to “VIDEO”.

AUDIO

AVR/AVC

VIDEO

2

Set the slide switch to the component to

be registered (VDP, VCR or TV).

DECK

MD

CD

LOCK

DVD

TV

VDP

VCR

)

Keep the POWER button pressed in

(when performing steps 3 and 4

3

Holding in the POWER button, press the

button for the corresponding manufacturer

in block A.

(Refer to Table 1.)

Flashes

4	Next, while holding the POWER button,
	press the button for the code in block B.
	(Refer to Table 1.) The operation is

completed when the button is released and the LEARNED/TX LED lights.

3

5	To continue registering other components,
	repeat steps 2 to 4.

1

	START	LEARNED/TX	RC-853
	START	LEARNED/TX
SYSTEM CALL		POWER
SET	CALL	OFF	ON / SOURCE
DVD	VDP	TUNER	SHIFT
1	2	3
TV/DBS	V.AUX	PHONO
4	5	6
VCR-1	CD	MD / TAPE-1	CHANNEL
7	8	9
VCR-2		TAPE-2 MON	TV/VCR
+10	0		A / B
VOLUME			DISC SKIP+
	DOLBY / DTS
HOME THX CINEMA	SURROUND	DIRECT
DSP SIMULATION	5CH STEREO	STEREO
			MASTER VOL.
INPUT MODE	ANALOG	EXT.IN
AUDIO	DECK MD
AUDIO	CD	LOCK	MUTING

AVR/AVC	VIDEO	DVD	TV
		VDP	VCR

	SYSTEM	SURROUND
TUNING	SETUP	PARAMETER
BAND	TITLE	MENU/GUIDE
BAND
		CH SELECT
MODE		ENTER
		SELECT
MEMORY	PANEL	ON SCREEN
	DISPLAY	RETURN
USE/LEARN T.TONE	MULTI	DVD
		SET UP

3,4

4

2

The LEARNED/TX LED flashes.

•This remote control unit can be used to operate components of other manufacturers without using the learning function by registering the manufacturer of the component as shown on Table 1.

Table 1: Combinations of Personal System Codes for Different Manufacturers

“DVD”

		B	DIRECT	STEREO	EXT.IN
		B
A			(DIRECT)	(STEREO)	(EXT. IN)

1	(DVD)		DENON A	DENON B	—
2	(VDP)		—	—	—

3	(TUNER)		—	—	—

4	(TV/DBS)		PANASONIC	—	—

5	(V. AUX)		—	—	—

6	(PHONO)		SONY	—	—

7	(VCR-1)		PIONEER	—	—

8(CD)			TOSHIBA	—	—

9	(MD/TAPE-1)		—	—	—

	(VCR-2)		—	—	—

			—	—	—

“VDP”

		B	DIRECT	STEREO	EXT.IN
A			(DIRECT)	(STEREO)	(EXT. IN)
A

1	(DVD)		DENON A	DENON B	DENON C
2	(VDP)		—	—	—

3	(TUNER)		MITSUBISHI	—	—

4	(TV/DBS)		PANASONIC	—	—

5	(V. AUX)		—	—	—

6	(PHONO)		SONY A	SONY B	SONY C

7	(VCR-1)		PIONEER	—	—

8	(CD)		—	—	—

9	(MD/TAPE-1)		—	—	—

	(VCR-2)		—	—	—

			—	—	—

2 Preset codes set upon shipment from the factory and when reset

30

Image 30

Contents AVR-5700 Safety Precautions Safety Instructions Table of Contents Before UsingFeatures Connecting the audio components ConnectionsConnecting video components Connecting a monitor TV Connecting a video component equipped with S-Video jacksPrecaution when using S-jacks Connecting the video decksConnecting the antenna terminals AM loop antenna assemblyConnection of AM antennas Connecting a DVD player DVD in jacks Connecting a monitor TV Monitor OUT jackConnecting the external input EXT. in jacks Connecting the Multi Source jacksSpeaker Impedance Connecting the speaker cordsSpeaker system connections ConnectionsProtector circuit Part Names and Functions Front PanelRemote control unit Power button …………………………36 Tuner buttons …………………………52Surround Parameter button Setting UP the SystemSystem Setup button Enter buttonSurround speaker selector function Before setting up the system Setting the type of speakersSystem Setup Menu reappears Setting the bass outputEnter the setting At the System Setup Menu select Bass OutputAt the System Setup Menu select Delay Time Setting the delay timeSubwoofer Only THX recommended THX mode Front & SubwooferSelect the desired unit, meters or feet Select darken the desired units, Meters or FeetSetting the channel level Test tone A, B or A+BSurr. Sp. a Volume can be adjusted between -12 dB and +12 dB in units When the Manual mode is selectedChannel Level screen reappears Subwoofer peak limit level setting AVR-5700 automatically sets the subwoofer peak limit levelSetting the digital inputs Setting the on-screen display OSD Auto tuner presetsAfter completing system setup On-screen display signalsRemote Control Unit Using the remote control unitInserting the batteries Operating Denon audio components Set mode switch 2 to the position for the component to beOperated. The tuner can be operated when the switch is at Any position but LockPreset memory VCR VCR or TV Operating a video component stored in the preset memorySet the slide switch to the component to be registered VDP Operate the video componentLearning function Using the system call function System call functionSystem call buttons Storing signals Clearing system call settingsOperation Before operatingPlaying the input source Select the input mode Selecting the analog modeInput mode selection function Select the input source to be playedAdjust the volume Select the play modeManual Auto mode Digital Auto mode Digital PCM mode Input mode when playing DTS sourcesAfter starting playback Adjusting the sound quality toneListening over headphones Turning the sound off temporarily mutingPlaying one source while recording another REC OUT mode Multi-source recording/playbackPlayback using the external input EXT. in jacks Multi-source and multi-zone playback Multi Room Music Entertainment SystemAdjust the level of the selected speaker SurroundBefore playing with the surround function Dolby Surround Pro Logic mode Fader functionSelect the Dolby Surround mode Set the input mode to Auto or RFSet the input mode to Auto or Digital DTS indicator lights when playing DTS sourcesLFE Low Frequency Effect Surround parameters Cinema EQ. Cinema EqualizerCOMP. Dynamic Range Compression Dialogue NormalizationHome THX Cinema mode Surround modes and their features DSP Surround SimulationPersonal Memory Plus Select the surround mode for the input channel DSP surround simulationWide Screen can only be selected from the main unit Tone control setting Select ToneSurround parameters Surround modes and parametersAuto tuning Manual tuningListening to the Radio Checking the preset stations Recalling preset stations Last Function MemoryInitialization of the Microprocessor Troubleshooting Optimum surround sound for different sources Types of multi-channel signalsAdditional Information Types of sources Movie audioSpeaker setting examples Basic setting for primarily watching moviesWhen using different surround speakers for movies and music 2Dolby Digital and Dolby Pro Logic SurroundDolby Surround Dolby Digital Dolby Surround AC-3 Dolby Digital compatible media and playback methodsDTS Digital Surround Dolby Pro LogicDTS compatible media and playback methods Timber matching circuit Home THX Cinema surround modeRe-equalizer Dynamic decorrelation circuitSurround modes and parameters AUX TAPE-1Specifications Audio section Power amplifier Rated outputPage 14-14, Akasaka 4-CHOME, MINATO-KU, Tokyo 107-8011, Japan