Denon AVR-5700 manual Setting the bass output, Enter the setting, System Setup Menu reappears

Page 19

4

Enter the setting.

a)

If no surround speakers are used (if “None” is set for both A and B):

ENTER

The System Setup Menu reappears.

b)If both surround speakers A and B are used (if either “Large” or “Small” is set for both A and B): The surround speaker setting screen appears.

c)If “None” is set for surround speakers A:

“None” is automatically set for surround speakers B.

NOTE:

Select “Large” or “Small” not according to the actual size of the speaker but according to the speaker’s capacity for playing low frequency (approximately 80 Hz and below) signals. If you do not know, try comparing the sound at both settings (setting the volume to a level low enough so as not to damage the speakers) to determine the proper setting.

Parameters

Large…… Select this when using speakers that can fully reproduce low sounds of below 80 Hz.

Small…… Select this when using speakers that cannot reproduce low sounds of below 80 Hz with sufficient volume. When this setting is selected, low frequencies of below 80 Hz are assigned to the subwoofer.

None…… Select this when no speakers are installed.

Yes/No… Select “Yes” when a subwoofer is installed, “No” when a subwoofer is not installed.

2If the subwoofer has sufficient low frequency playback capacity, good sound can be achieved even when “Small” is set for the front, center and surround speakers.

2To take full advantage of the performance of the Home THX certified speaker systems, set the front, center and surround speaker size parameters to “Small” and the subwoofer to “Yes”.

2For the majority of speaker system configurations, using the SMALL setting for all five main speakers and Subwooofer On with a connected subwoofer will yield the best results.

Selecting the surround speakers for the different surround modes

• At this screen preset the surround speakers to be used in the different surround modes.

1

2

When either “Large” or “Small” has been set for both speakers A and B on the System Setup Menu (when using both A and B surround speakers), the surround speaker setting screen appears.

Select the surround speakers to be used in the different surround modes.

• To select the surround mode

• To select the surround speaker

A:When using surround speakers A

B: When using surround speakers B

A+B: When using both surround speakers A and B

Enter the setting.

The System Setup Menu reappears.

ENTER

2Speaker type setting when using both surround speakers A and B

If “Small” is set for either surround speakers A or B, the output is the same as when “Small” is set for both A and B.

Setting the bass output

1

At the System Setup Menu select “Bass Output”.

 

19

Image 19
Contents AVR-5700 Safety Precautions Safety Instructions Before Using Table of ContentsFeatures Connections Connecting the audio componentsConnecting video components Connecting the video decks Connecting a video component equipped with S-Video jacksPrecaution when using S-jacks Connecting a monitor TVAM loop antenna assembly Connecting the antenna terminalsConnection of AM antennas Connecting a monitor TV Monitor OUT jack Connecting a DVD player DVD in jacksConnecting the Multi Source jacks Connecting the external input EXT. in jacksConnections Connecting the speaker cordsSpeaker system connections Speaker ImpedanceProtector circuit Front Panel Part Names and FunctionsPower button …………………………36 Tuner buttons …………………………52 Remote control unitEnter button Setting UP the SystemSystem Setup button Surround Parameter buttonSurround speaker selector function Setting the type of speakers Before setting up the systemAt the System Setup Menu select Bass Output Setting the bass outputEnter the setting System Setup Menu reappearsFront & Subwoofer Setting the delay timeSubwoofer Only THX recommended THX mode At the System Setup Menu select Delay TimeSelect darken the desired units, Meters or Feet Select the desired unit, meters or feetTest tone A, B or A+B Setting the channel levelSurr. Sp. a When the Manual mode is selected Volume can be adjusted between -12 dB and +12 dB in unitsChannel Level screen reappears AVR-5700 automatically sets the subwoofer peak limit level Subwoofer peak limit level settingSetting the digital inputs Auto tuner presets Setting the on-screen display OSDOn-screen display signals After completing system setupUsing the remote control unit Remote Control UnitInserting the batteries Any position but Lock Set mode switch 2 to the position for the component to beOperated. The tuner can be operated when the switch is at Operating Denon audio componentsPreset memory VCR Operate the video component Operating a video component stored in the preset memorySet the slide switch to the component to be registered VDP VCR or TVLearning function System call function Using the system call functionSystem call buttons Clearing system call settings Storing signalsBefore operating OperationSelect the input source to be played Select the input mode Selecting the analog modeInput mode selection function Playing the input sourceInput mode when playing DTS sources Select the play modeManual Auto mode Digital Auto mode Digital PCM mode Adjust the volumeTurning the sound off temporarily muting Adjusting the sound quality toneListening over headphones After starting playbackMulti-source recording/playback Playing one source while recording another REC OUT modePlayback using the external input EXT. in jacks Multi Room Music Entertainment System Multi-source and multi-zone playbackSurround Adjust the level of the selected speakerBefore playing with the surround function Fader function Dolby Surround Pro Logic modeDTS indicator lights when playing DTS sources Set the input mode to Auto or RFSet the input mode to Auto or Digital Select the Dolby Surround modeDialogue Normalization Surround parameters Cinema EQ. Cinema EqualizerCOMP. Dynamic Range Compression LFE Low Frequency EffectHome THX Cinema mode DSP Surround Simulation Surround modes and their featuresPersonal Memory Plus DSP surround simulation Select the surround mode for the input channelWide Screen can only be selected from the main unit Select Tone Tone control settingSurround modes and parameters Surround parametersManual tuning Auto tuningListening to the Radio Checking the preset stations Last Function Memory Recalling preset stationsInitialization of the Microprocessor Troubleshooting Types of sources Movie audio Types of multi-channel signalsAdditional Information Optimum surround sound for different sourcesBasic setting for primarily watching movies Speaker setting examplesWhen using different surround speakers for movies and music Dolby Digital compatible media and playback methods SurroundDolby Surround Dolby Digital Dolby Surround AC-3 2Dolby Digital and Dolby Pro LogicDolby Pro Logic DTS Digital SurroundDTS compatible media and playback methods Dynamic decorrelation circuit Home THX Cinema surround modeRe-equalizer Timber matching circuitAUX TAPE-1 Surround modes and parametersAudio section Power amplifier Rated output SpecificationsPage 14-14, Akasaka 4-CHOME, MINATO-KU, Tokyo 107-8011, Japan