Axis Communications P7210 user manual QoS Quality of Service, UPnPTM, RTP/H.264

Page 45

AXIS P7210 Video Encoder

System Options

QoS (Quality of Service)

QoS (Quality of Service) guarantees a certain level of a specified resource to selected traffic on a network. A QoS-aware network prioritizes network traffic and provides a greater network reliability by controlling the amount of bandwidth an application may use.

The QoS settings are configured under System Options > Network > QoS. Using DSCP (Differentiated Services Codepoint) values, the Axis product can mark the following types of traffic: live video, live audio, event/alarm traffic and management traffic.

Note

Live audio DSCP will be equal to live video DSCP if H.264 over RTSP is used.

SNMP

The Simple Network Management Protocol (SNMP) allows remote management of network devices. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups.

The Axis product can be configured to support SNMP on the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

SNMP v1/v2 provides the lowest level of security. The community name can be specified as a password for read or read/write access to all supported SNMP devices. The default password for the Read community is public and the default password for the Write community is write.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS, on page 39. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings, on page 49.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

45

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Axis P7210 Video Encoder Legal Considerations About this DocumentLiability Intellectual Property RightsLearn More SupportAxis P7210 Video Encoder Table of ContentsBNC Connector Connectors and ButtonsNetwork Connector Hardware OverviewPower Connector ConnectorAudio Connector RS485/RS422 ConnectorColor Indication Hardware Overview LED IndicatorsAccessing the Product Accessing the ProductAccess from a Browser Start a browser Internet Explorer, Firefox, SafariSet the Root Password Accessing the Product Access from the InternetNetwork TCP/IP Advanced Click Use HttpsLive View Controls on the Live ViewAxis Media Control viewer toolbar AMC Audio Controls PTZ ControlsAxis P7210 Video Encoder Media Streams How to Stream H.264Media Streams Axis Media Control AMCQuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Accessing Audio StreamsSetting Up the Product Setting Up the ProductBasic Setup Video and Audio Video and AudioVideo Stream Pixel Counter Click Save to apply the new settingsImage 264Quad stream Camera SettingsStream Profiles Image AppearanceOverlay Image SettingsOverlay Image Go to Video & Audio Video Stream and select the Image tabUsing Overlay Text in an Action Rule Privacy MaskGo to Events Action Rules Video and Audio Audio Settings Audio ModesAudio Input Audio Output Audio ClipsLive View Config Live View ConfigDefault live view video Viewer Settings Default Viewer for BrowsersUser Defined Links Output ButtonsGo to Setup Live View Config Go to PTZ Preset Positions Preset PositionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomPTZ Pan Tilt Zoom Guard Tour Device SettingsAdvanced LimitsOSD Menu Installing a PTZ driverDetectors DetectorsCamera Tampering Motion DetectionMotion Detection Parameters Set Up Motion Detection WindowsGo to Detectors Motion Detection Parameter Object Size History Sensitivity DescriptionAudio Detection Events EventsTime Setting Up an Action RulePTZ Control Go to Events Action Rules and click AddRecipients Recipient Use with actionGo to Events Recipients and click Add Schedules Setting Up an Email RecipientRecurrences Go to Events Schedules and click AddRecordings RecordingsRecording List Continuous RecordingLanguages LanguagesSystem Options System OptionsSecurity UsersIeee CertificatesGo to System Options Security Ieee Click Install certificate and upload the certificate To install a self-signed certificateDate & Time Audio SupportSystem Options Network Basic TCP/IP SettingsDNS Configuration Advanced TCP/IP SettingsNTP Configuration Host Name ConfigurationFTP NAT traversal port mapping for IPv4UPnPTM can be disabled under System Options Network UPnPTM QoS Quality of ServiceUPnPTM RTP/H.264Bonjour StorageSD Card Go to System Options Storage and click SD CardNetwork Share Ports & DevicesPorts COM PortSupport System Options MaintenanceSupport Overview System OverviewPlain Config Reset to Factory Default SettingsScripting File UploadAxis P7210 Video Encoder Troubleshooting TroubleshootingEmergency Recovery Procedure Checking the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externally Problems with streaming H.264Basic Video and image problems, general Status and Network indicator LEDs are flashing red rapidlySetup Video & Audio Camera Settings SettingsStorage disruption Storage and disk management problemsRe-mount the storage device Reformat the SD card and then click MountTechnical Specifications Technical SpecificationsMemory Power Function/group Specifications System ApplicationConnectors WeightFunction Pin Specifications Technical Specifications ConnectorsPerformance Considerations RS-485/422 ConnectorAudio Input Audio Output Function PinAxis P7210 Video Encoder M3.8
Top Page Image Contents