Axis Communications P7210 user manual Power Connector, Audio Connector, RS485/RS422 Connector

Page 6

AXIS P7210 Video Encoder

Hardware Overview

NOTICE

The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network switch shall be shielded (STP) and intended for their specific use. Make sure that the network switch is properly grounded. For information about regulatory requirements, see Regulatory Information, on page 2 .

I/O Connector

Use in applications for e.g. motion detection, event triggering, time lapse recording and alarm notifications. In addition to an auxiliary power and a GND pin, the I/O terminal connector provides the interface to:

Digital output – For connecting external devices such as relays and LEDs. Connected devices can be activated by the VAPIX® Application Programming Interface, output buttons on the Live View page or by an Action Rule. The output will show as active (shown under System Options > Ports & Devices) if the alarm device is activated.

Digital input – An alarm input for connecting devices that can toggle between an open and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. When a signal is received the state changes and the input becomes active (shown under System Options > Ports & Devices).

Power Connector

2-pin terminal block for power input. Use a Safety Extra Low Voltage (SELV) compliant limited power source (LPS) with either a rated output power limited to 100 W or a rated output current limited to 5 A.

Audio Connector

The Axis product has the following audio connectors:

Audio in (pink) – 3.5 mm input for a mono microphone, or a line-in mono signal (left channel is used from a stereo signal).

Audio out (green) – 3.5 mm output for audio (line level) that can be connected to a public address (PA) system or an active speaker with a built-in amplifier. A stereo connector must be used for audio out.

RS485/RS422 Connector

Two terminal blocks for RS485/RS422 serial interface used to control auxiliary equipment such as PTZ devices.

SD Card Slot

An SD card (not included) can be used for local recording with removable storage. For more information, see Technical Specifications.

NOTICE

To prevent corruption of recordings, the SD card should be unmounted before removal. To unmount, go to Setup > System Options > Storage > SD Card and click Unmount.

Control Button

The control button is used for:

Resetting the product to factory default settings. See page 49.

Connecting to an AXIS Video Hosting System service. See page 42. To connect, press and hold the button for about 1 second until the Status LED flashes green.

Connecting to AXIS Internet Dynamic DNS Service. See page 42. To connect, press and hold the button for about 3 seconds.

6

Image 6
Contents Axis P7210 Video Encoder Liability About this DocumentLegal Considerations Intellectual Property RightsSupport Learn MoreTable of Contents Axis P7210 Video EncoderNetwork Connector Connectors and ButtonsBNC Connector Hardware OverviewAudio Connector ConnectorPower Connector RS485/RS422 ConnectorHardware Overview LED Indicators Color IndicationAccess from a Browser Accessing the ProductAccessing the Product Start a browser Internet Explorer, Firefox, SafariNetwork TCP/IP Advanced Accessing the Product Access from the InternetSet the Root Password Click Use HttpsLive View Controls on the Live ViewAxis Media Control viewer toolbar PTZ Controls AMC Audio ControlsAxis P7210 Video Encoder Media Streams How to Stream H.264Media Streams Axis Media Control AMCAlternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAccessing Audio Streams Java applet supports simplex audio with G.711 encodingSetting Up the Product Setting Up the ProductBasic Setup Video and Audio Video and AudioVideo Stream Image Click Save to apply the new settingsPixel Counter 264Stream Profiles Camera SettingsQuad stream Image AppearanceOverlay Image Image SettingsOverlay Go to Video & Audio Video Stream and select the Image tabUsing Overlay Text in an Action Rule Privacy MaskGo to Events Action Rules Video and Audio Audio Settings Audio ModesAudio Input Audio Clips Audio OutputLive View Config Live View ConfigDefault live view video User Defined Links Default Viewer for BrowsersViewer Settings Output ButtonsGo to Setup Live View Config PTZ Pan Tilt Zoom Preset PositionsGo to PTZ Preset Positions PTZ Pan Tilt ZoomAdvanced Device SettingsPTZ Pan Tilt Zoom Guard Tour LimitsInstalling a PTZ driver OSD MenuCamera Tampering DetectorsDetectors Motion DetectionGo to Detectors Motion Detection Set Up Motion Detection WindowsMotion Detection Parameters Parameter Object Size History Sensitivity DescriptionAudio Detection Events EventsPTZ Control Setting Up an Action RuleTime Go to Events Action Rules and click AddRecipients Recipient Use with actionGo to Events Recipients and click Add Recurrences Setting Up an Email RecipientSchedules Go to Events Schedules and click AddRecording List RecordingsRecordings Continuous RecordingLanguages LanguagesSecurity System OptionsSystem Options UsersIeee CertificatesGo to System Options Security Ieee Date & Time To install a self-signed certificateClick Install certificate and upload the certificate Audio SupportBasic TCP/IP Settings System Options NetworkNTP Configuration Advanced TCP/IP SettingsDNS Configuration Host Name ConfigurationNAT traversal port mapping for IPv4 FTPUPnPTM QoS Quality of ServiceUPnPTM can be disabled under System Options Network UPnPTM RTP/H.264SD Card StorageBonjour Go to System Options Storage and click SD CardPorts Ports & DevicesNetwork Share COM PortSupport Overview System Options MaintenanceSupport System OverviewScripting Reset to Factory Default SettingsPlain Config File UploadAxis P7210 Video Encoder Emergency Recovery Procedure TroubleshootingTroubleshooting Checking the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externally Problems with streaming H.264Basic Setup Video & Audio Camera Settings Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general SettingsRe-mount the storage device Storage and disk management problemsStorage disruption Reformat the SD card and then click MountTechnical Specifications Technical SpecificationsConnectors Function/group Specifications System ApplicationMemory Power WeightTechnical Specifications Connectors Function Pin SpecificationsAudio Input Audio Output RS-485/422 ConnectorPerformance Considerations Function PinAxis P7210 Video Encoder M3.8