Fisher-Price 79701 owner manual Car, Have to drill a 5/16 hole. Be sure to wear, Another wrench

Page 42

Tether Anchor Installation 2-Door and 4-Door Car

	(22 - 40 LBS.)				Bolt
	UP				Bolt
			Distance		3"
			from top of		3"
	AND		from top of		Anchor
			car seat and	3"	Anchor
			hole is at
			least 8".
	1 YEAR				Car
					Center
			Washer		Seat
			Washer		Line
			Lock Nut
	POSITION		Lock Nut
		4A	If a pre-drilled hole does not exist, you will
			have to drill a 5/16" hole. (Be sure to wear
			appropriate eye protection when drilling.)
			appropriate eye protection when drilling.)
	FORWARD-FACING		Make sure the hole is at least 8" away from
			the top and no more than 3" from the center
			line of the Safe Embrace® Convertible
			Car Seat.
		5A	Insert the bolt through the anchor.
		6A	Insert the end of the bolt into the hole
			inside your vehicle.
		7A	Open the trunk of your vehicle and attach
		7A	Open the trunk of your vehicle and attach
			the washer and lock nut to the end of the
			bolt. While holding the bolt tight with a
			wrench, tighten the lock nut securely with
			another wrench.

41

Image 42

Contents Safe Embrace Table of Contents Message to Parents Page Page Page For Your Information Surrounds your child with an extra layer of protection Adds greater strength than car seats with all plastic framesEep your child safer Selecting a Vehicle Seating Location For Your Car Seat Always use vehicle seats That face the front of the vehicle Use vehicle seats That face the side VehicleWhat Kind of Vehicle Belt System Do You Have? These Vehicle Belt Systems You will not be able to keep the car seat secureOnly USE Lap belt is tightened by pulling on its free endRear-Facing Position Harness Adjustment Strap Rear-Facing Position Birth to 1 Year 6 -30 lbsPath Opening Rear-Facing Setup Point Harness Make sure both shoulder straps are inserted into the buckleFront of the car seat Setup Point Harness Shoulder strap slots Position only if your child’s shoulders are at Pull the connector bar up on the back of the car seat Setup Seat Position Recline Close the connector bar cover. REAR-FACINGBottom of the car seat B Installing Your Car Seat in a Vehicle Never install and restrain a childSee inset will help keep it clean Car seat Buckle the vehicle belt Begins to rise 5B For a manual lap belt system Correct Installing Your Car Seat in a Vehicle Installing Your Car Seat in a Vehicle Correct Incorrect Restraining Your Child Position the crotch strap between your Child’s legs Insert each of the shoulder straps intoRestraining Your Child Restraining Your Child To remove your child from the car seat Insert both shoulder straps into the buckleForward-Facing Position Belt Path Strap Slots Tether StrapForward-Facing HarnessTether Anchor Installation Tether Anchor Tether StrapTether Anchor Tether Strap Tether Anchor Installation Have to drill a 5/16 hole. Be sure to wear Appropriate eye protection when drillingCar Line of the Safe Embrace ConvertibleNo more than 4 from the center line Still accessible by the tether strapIf a pre-drilled hole does not exist, you will Safe Embrace Convertible Car SeatTether Anchor Installation Pick-Up Truck Setup Point Harness Setup Point Harness Tongue face each other. Fasten the chest clip Setup Point Harness Close the connector bar cover Setup Seat-Position Upright Pull the seat position adjusterYou B Installing Your Car Seat in a Vehicle Opposite side of the car seat Front of VehicleBuckle the vehicle belt 4A For a lap and shoulder belt system 4B For a manual lap belt system Installing Your Car Seat in a Vehicle To Remove Correct Metal and plastic parts of the car seat Straps are not twisted Restraining Your Child Buckle the chest clip Restraining Your Child Restraining Your Child Unbuckle the chest clip Consumer Information Aircraft Use Register Your Safe Embrace Convertible Car Seat Cleaning and Washing Seat padNot use bleach Cleaning and Washing Page Safe Check