Fisher-Price 79701 owner manual If a pre-drilled hole does not exist, you will

Page 43

Tether Anchor Installation

Van, Hatchback, Station

Wagon, Sport Utility Vehicle

				- 40 LBS.)
		Bolt		(22
		Anchor
				UP
	Hole is
		4"		AND
	behind
		4"
	vehicle seat
		Car
	and still		Seat

	accessible by
		Center		YEAR
	tether strap.		Line
		Washer
	Lock Nut
				1

4B	If a pre-drilled hole does not exist, you will			POSITION
	have to drill a 5/16" hole. (Be sure to wear
	appropriate eye protection when drilling.)
	Make sure the hole is behind the vehicle seat
	and still accessible by the tether strap; and			FORWARD-FACING
	no more than 4" from the center line of the
	Safe Embrace® Convertible Car Seat.
5B	Insert the bolt through the anchor.
6B	Insert the end of the bolt into the hole inside
	your vehicle.
7B	From the outside or underside of your vehi-
	cle, attach the washer and lock nut to the
	end of the bolt. While holding the bolt tight

	with a wrench, tighten the lock nut securely
	with another wrench. If the drilled hole is on
	the floor of your vehicle, use a silicone caulk
	to seal out water and exhaust fumes.

42

Image 43

Contents Safe Embrace Table of Contents Message to Parents Page Page Page For Your Information Adds greater strength than car seats with all plastic frames Surrounds your child with an extra layer of protectionEep your child safer Selecting a Vehicle Seating Location For Your Car Seat Use vehicle seats That face the side Vehicle Always use vehicle seats That face the front of the vehicleWhat Kind of Vehicle Belt System Do You Have? You will not be able to keep the car seat secure These Vehicle Belt SystemsLap belt is tightened by pulling on its free end Only USERear-Facing Position Rear-Facing Position Birth to 1 Year 6 -30 lbs Harness Adjustment StrapPath Opening Rear-Facing Make sure both shoulder straps are inserted into the buckle Setup Point HarnessFront of the car seat Setup Point Harness Shoulder strap slots Position only if your child’s shoulders are at Pull the connector bar up on the back of the car seat Close the connector bar cover. REAR-FACING Setup Seat Position ReclineBottom of the car seat B Never install and restrain a child Installing Your Car Seat in a VehicleSee inset will help keep it clean Car seat Buckle the vehicle belt Begins to rise 5B For a manual lap belt system Correct Installing Your Car Seat in a Vehicle Installing Your Car Seat in a Vehicle Correct Incorrect Restraining Your Child Insert each of the shoulder straps into Position the crotch strap between your Child’s legsRestraining Your Child Restraining Your Child Insert both shoulder straps into the buckle To remove your child from the car seatForward-Facing Position Harness Strap Slots Tether StrapForward-Facing Belt PathTether Anchor Tether Strap Tether Anchor InstallationTether Anchor Tether Strap Tether Anchor Installation Line of the Safe Embrace Convertible Appropriate eye protection when drillingCar Have to drill a 5/16 hole. Be sure to wearSafe Embrace Convertible Car Seat Still accessible by the tether strapIf a pre-drilled hole does not exist, you will No more than 4 from the center lineTether Anchor Installation Pick-Up Truck Setup Point Harness Setup Point Harness Tongue face each other. Fasten the chest clip Setup Point Harness Close the connector bar cover Pull the seat position adjuster Setup Seat-Position UprightYou B Installing Your Car Seat in a Vehicle Front of Vehicle Opposite side of the car seatBuckle the vehicle belt 4A For a lap and shoulder belt system 4B For a manual lap belt system Installing Your Car Seat in a Vehicle To Remove Correct Metal and plastic parts of the car seat Straps are not twisted Restraining Your Child Buckle the chest clip Restraining Your Child Restraining Your Child Unbuckle the chest clip Consumer Information Aircraft Use Register Your Safe Embrace Convertible Car Seat Seat pad Cleaning and WashingNot use bleach Cleaning and Washing Page Safe Check