Graco PD261464A manual Safe Vehicle Belt Systems, Lap Belts Manually Adjusted Belt tail

Page 29

6.2.2SAFE Vehicle Belt Systems

THE FOLLOWING BELT SYSTEMS CAN BE USED WITH YOUR INFANT RESTRAINT, IF the seat location meets all other requirements of these instructions and those in your vehicle owner’s manual. LATCH can be used in place of the vehicle belt system. Please refer to vehicle owner’s manual for LATCH locations.

When using infant restraint without the base, adjust the belt as described in this section for these types of vehicle seat belts.

When using the base to install the infant restraint, you must ALWAYS use the Lock-off to secure the lap belt or lap/shoulder belt. See “7.3 Installing the Infant Restraint and Base Using Vehicle Belt”, page 36 for installation instructions when using the base.

Some vehicle lap/shoulder seat belts have a plastic button on the belt. Do not allow the button to interfere with the belt routing through the vehicle belt path when installing the seat alone, or with the lock-off when installing the seat and the base.

Lap Belts - Manually Adjusted Belt tail

When buckled, the belt is tightened manually by pulling on the belt tail while pushing down hard on the child restraint.

29

Image 29

Contents SnugRide Classic Connect 20-25 Features and Components 13-19Additional Information 43-46 How to Install the Infant Restraint/Base 33-42Choosing an Appropriate Vehicle Seat Location 26-32 Do not Place this Infant Restraint Properly reclining the infant restraint For Recall Information Registration InformationRegister Your Infant Restraint Child Restraint Useful Life If You Need HelpImportant Information ‡ Never Leave Your Child Unattended Connect Travel SYSTEM. Refer to ‡ USE only with Strollers That are Part of the Graco ClassicAdditional Warnings for Use as a Carrier Your child Must meet the following requirements Height and Weight LimitsFront View Features and ComponentsLevel IndicatorLocking ClipLatch Latch LatchRemoving and Attaching Infant Restraint Adjusting HandleAttaching Canopy With the HARNESS. Harness must 2-Part Body SupportThat Nothing Interferes Harness Covers on certain models, styles vary Cold Weather Boot on certain models, styles varyEven with or just below your child’s Using Infant RestraintPositioning Harness Straps Safety Check Shoulder Straps for a Larger Baby žTo Lengthen Waist Straps for a Larger Baby Ÿ ¡Securing Child in Infant Restraint Gracobaby.com Vehicle Seat Requirements Choosing an Appropriate Vehicle Seat LocationVehicle Seat Belt Requirements ‡ Lap Belts Forward of Seat Crease Unsafe Vehicle Belt SystemsSafe Vehicle Belt Systems ‡ Lap Belts Manually Adjusted Belt tail‡ Combination Lap/Shoulder Belt with Locking Latch Plate ‡ Lap Belts with Automatic Locking Retractor ALR‡ Combination Lap/Shoulder Belt with Sliding Latch Plate To Install Locking Clip do not use with baseLatch Locations How to Install the Infant Restraint/Base Belt should not be twisted or turned Page Installing the Infant Restraint and Base Using Vehicle Belt Page Page Belt must lay flat and not be twisted Using Latch to install BaseReclining Infant Restraint/Base To Adjust Recline on Base Final Safety Check Every time you drive with your child Additional InformationAirplane Use Storing LatchTo Remove and Wash Cleaning and MaintenancePage Prevent Serious Injury or Death Buckle Cleaning ProcessPage Replacement Parts SnugRide Classic Connect Información importante Funciones y componentes 13-19Información adicional 43-46 Instalación del sistema de seguridad para bebés/base 33-42Advertencias a padres y otros dueños Para su niño Información sobre el retiro de productos del mercado Información sobre el registroRegistro de su sistema de seguridad para bebés Vida útil del sistema de seguridad para niños Si necesita ayudaAdvertencias para uso como sistema de seguridad para bebés Información importante‡ Nunca Deje a SU Niño Solo Classic Connect DE GRACO. Consulte Advertencias para el uso con un cochecitoAdvertencias adicionales para el uso como transportador Su niño Debe cumplir todos los requisitos Limitaciones de peso y estaturaVista Delantera Funciones y componentesDel nivel IndicadorTraba de SeguridadDel Latch Sacar y conectar el sistema de seguridad para bebés Ajuste de la manijaColocación de la capota Soporte del Cuerpo de 2 partes Cubiertas de arnés ciertos modelos Bota para tiempo frío en ciertos modelos, los estilos varíanColocación de las correas del arnés Uso del sistema de seguridad para bebésVerificación DE Seguridad Grande Correas para los hombros para un niño MÁSŸ ¡ Sujetar el niño en el sistema de seguridad Verifique que las correas del arnés no Requisitos del asiento del vehículo Cómo elegir un lugar apropiado para el asiento del vehículoRequisitos del cinturón de seguridad del vehículo Sistemas Peligrosos de cinturones de vehículos Sistemas Seguros de cinturones de vehículos Page Para instalar la traba de seguridad no lo use con la base Ubicación del Latch Instalación del sistema de seguridad para bebés/base Page 26-32 Traba Deben pasar Page Sin doblarse El cinturón debe mantenerse en posición planaInclinación del sistema de seguridad para bebés/base Para ajustar la inclinación sobre la base Page Almacenamiento del Latch Información adicionalPara Sacar Y Lavar Limpieza y mantenimientoPage Prevenga Lesiones Graves O LA Muerte Proceso de limpieza de la hebillaNotas Piezas de repuesto