Allstar Products Group HDSWG 1000 owner manual Installing the Operator, Electrical Hook UP

Page 11

WARNING!

RISK OF ENTRAPMENT.

TO MINIMIZE POTENTIAL FOR GATE CONTROLS TO BE ACTIVATED WHILE ALREADY IN USE, LOCATE THE HDSWG 1000 CONTROL BOX IN FULL VIEW OF THE GATE.

C:INSTALLING THE OPERATOR

ELECTRICAL HOOK UP

The HDSWG 1000 electrical connection is made at the electrical junction box provided in the HDSWG 1000 CONTROL BOX, see Figure 11. There are three cutouts on the bottom of the CONTROL BOX to permit conduit entry. Run a flexible water tight conduit from the service junction box to the access hole that is just under the junction box containing the main power switch of the HDSWG 1000. Pull three #14 wires from the service junction box to the junction box inside the HDSWG 1000 Control Box. If the HDSWG 1000 is wired for 115 Volts, pull a black, white and green wire. If the HDSWG 1000 is wired for 230 Volts, pull a black, red and green wire.

INSTALLING THE HDSWG 1000 CONTROL BOX

The HDSWG 1000 CONTROL BOX may be mounted remotely from the MECHANICAL UNIT. Four mounting holes are provided at the back of the CONTROL BOX. These should be used to mount the CONTROL BOX to a solid, flat surface. Use a caulking material around the holes to ensure a water tight seal. The CONTROL BOX should be located so that the Gate and the

MECHANICAL UNIT/UNITS ARE IN FULL VIEW FROM

THE CONTROL BOX.

105100

WARNING!

TO AVOID ELECTRICAL DAMAGE TO OPERATOR DO NOT ALLOW TOTAL WIRE LENGTH FROM THE CONTROL BOX TO AC POWER SERVICE PANEL PLUS THE DISTANCE FROM THE CONTROL BOX TO THE MECHANICAL UNIT TO EXCEED WIRE LENGTH GIVEN IN TABLE 1 FOR AC SERVICE.

Figure 11: Schematic & Wiring Diagram

11

Image 11
Contents Hdswg Pre-Setting the Motor Overload Sensitivity LOG Date Overload Test Date Tested Dates Operator Serviced PRE-INSTALLATIONGate System Design and Installation Safety Check List Concrete PAD Important Installation NotesAS the Installer YOU are Responsible for Swing Gate Entrapment ProtectionPlacing the Vehicle Detector Loops Preparing the SiteVehicle Detector Loop Blanking for Swing Gates Electrical Power RequirementsService Conduit Other Voltages and Three Phase SystemsTools Required InstallingPlacing the Hdswg 1000 Mechanical Unit Installing the Hdswg 1000 ARMElectrical Hook UP Installing the OperatorInstalling the Hdswg 1000 Control BOX Volt Installations Connecting the AC WiringConnecting the Mechanical Unit to the Control BOX BI-PARTING WiringLeft/Right Hand Installation Limit & Motor Wiring Diagram Bi-Parting Installation Limit & Motor Wiring Diagram Wiring Radio Receivers to the Terminal Strip Accessory Equipment HOOK-UPThree Terminal Receivers Four Wire ReceiversWiring a 3-BUTTON Station Connecting the Vehicle Detector to the Hdswg Wiring a KEYPAD, Card Reader or Telephone Entry SystemVehicle Detector Power Wiring Vehicle DetectorsDescription # NameSetting the Switch Selectable Options Setting the Limit Switches RIGHT-HANDED OperationSetting the Limit Switches LEFT-HANDED Operation Presetting the Motor Overload SensitivityChecking the Indicator Lights Applying Power to the HdswgTimer to Close Setting PRE-POWER Check ListRunning the Hdswg PRE POWER-ON ChecklistFinal Setting of the Motor Overload Sensitivity Maximum RUN TimerFinal Setting of the Close Timer Vehicle Detectors Installation Notes for Auxiliary EquipmentPrecautions for Pedestrian Traffic or Residential Areas Gate Opener System Operation & Safety GuideMaintain ALL Components of Gate System Gate Opener System Operation & SafetyMaintain the Gate and Gate Hardware a Hdswg 1000 Mechanical Unit Exploded View Mechanical Unit Exploded ViewARM KIT & Control BOX Exploded View & Parts Mechanical Unit Parts ListCapacities Technical SpecificationsPhysical Drive Electrical