Allstar Products Group HDSWG 1000 Technical Specifications, Physical Drive, Electrical

Page 28

TECHNICAL SPECIFICATIONS

PHYSICAL

DRIVE

PAD:

OVERHEAD CLEARANCE: UNIT SIZE:

FRAME:

COVER: SHIPPING WEIGHT:

24W x 30D x 3H

21 Inch Minimum

16-1/8 x 24-7/8 x 17-1/4

Welded steel, Coated to UL Standards Molded Polyethylene

150 lbs.

DRIVE SYSTEM: TORQUE LIMITER:

OUTPUT SHAFT: LIMITS:

60:1 Gearbox

Mounted on Output Shaft, Adjustable

1-1/4 Diameter Ball-Bearing Mounted

Independent Open & Close; Displaced Cam with Micro Switch

PRIMARY VOLTAGE: ELECTRICAL SOURCE:

CONTROL VOLTAGE:

RADIO RECEIVER POWER:

MOTOR:

ELECTRICAL

115 VAC, 60 Hz

One 3-Wire 15 AMP Service per Operator

12/24 VDC 24 VAC

1/2 HP, 4.4 AMP PSC, Instant Reversing

CAPACITIES

MAX. GATE WEIGHT: 1000 lbs.

MAX. GATE WIDTH: 18 Feet

MAX. CYCLES PER HOUR: 60 Open/Close per Hour 1200 Open/Close per Day

GATE SPEED: 13-15 Seconds for 90º Opening

Specifications subject to change without notice. Consult the factory.

Manufacturer’s Limited Warranty

Allstar warrants its gate operators to be free from defect in material and workmanship for a period of five (5) years from the date of purchase for single family home use and three (3) years from the date of purchase for multi-family and commercial use. This warranty covers all components except the electronic circuit boards which are warranted for three (3) years from the date of purchase for single family home use and two (2) years from the date of purchase for multi-family and commercial use. To obtain service contact your dealer.

To obtain service under this warranty the buyer must obtain authorization instructions for the return of any goods from Allstar before returning the goods. The goods must be returned with complete identification, with copy of proof-of-purchase, freight prepaid and in accordance with Allstar’s instructions or they will not be accepted. In no event will Allstar be responsible for goods returned without proper authorization or identification.

Goods returned to Allstar for warranty repair within the warranty period, which upon receipt by Allstar are confirmed to be defective and covered by this limited warranty, will be repaired or replaced at Allstar’s sole option, at no cost and returned pre-paid. Defective parts will be repaired or replaced with new or factory rebuilt parts at Allstar’s sole option.

This limited warranty does not cover non-defect damage, damage caused by unreasonable use, damage caused by improper installation or

care, vandalism or lightning, fire or excessive heat, flood or other acts of God (including, but not limited to misuse, abuse or alterations, failure to provide reasonable and necessary maintenance), labor charges for dismantling or reinstalling a repaired or replaced unit, or replacement batteries.

These warranties are in lieu of all other warranties, either expressed or implied. All implied warranties of merchantability and/or fitness for a particular purpose are hereby disclaimed and excluded. Under no circumstances shall Allstar be liable for consequential, incidental or special damages arising in connection with the use or inability to use this product. In no event shall Allstar’s liability for breach of warranty, breach of contract, negligence or strict liability exceed the cost of the product covered hereby. No person is authorized to assume for Allstar any other liability in connection with the sale of this product.

This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Warranty effective after May 15th, 1997.

For Information:

Phone 610-436-6190 FAX 610-344-0210

c.p. Allstar Corporation Downingtown, PA 19335

This Gate Operator is built in the USA and complies with all requirements of Underwriters' Laboratories Standard UL-325. P/N 107765 Rev. A, 5/97

28

Image 28
Contents Hdswg Pre-Setting the Motor Overload Sensitivity PRE-INSTALLATION LOG Date Overload Test Date Tested Dates Operator ServicedGate System Design and Installation Safety Check List Important Installation Notes AS the Installer YOU are Responsible forSwing Gate Entrapment Protection Concrete PADPreparing the Site Placing the Vehicle Detector LoopsElectrical Power Requirements Vehicle Detector Loop Blanking for Swing GatesOther Voltages and Three Phase Systems Service ConduitInstalling Tools RequiredInstalling the Hdswg 1000 ARM Placing the Hdswg 1000 Mechanical UnitInstalling the Hdswg 1000 Control BOX Installing the OperatorElectrical Hook UP Connecting the AC Wiring Connecting the Mechanical Unit to the Control BOXBI-PARTING Wiring Volt InstallationsLeft/Right Hand Installation Limit & Motor Wiring Diagram Bi-Parting Installation Limit & Motor Wiring Diagram Accessory Equipment HOOK-UP Wiring Radio Receivers to the Terminal StripWiring a 3-BUTTON Station Four Wire ReceiversThree Terminal Receivers Wiring a KEYPAD, Card Reader or Telephone Entry System Vehicle Detector PowerWiring Vehicle Detectors Connecting the Vehicle Detector to the Hdswg# Name DescriptionSetting the Limit Switches RIGHT-HANDED Operation Setting the Limit Switches LEFT-HANDED OperationPresetting the Motor Overload Sensitivity Setting the Switch Selectable OptionsApplying Power to the Hdswg Timer to Close SettingPRE-POWER Check List Checking the Indicator LightsPRE POWER-ON Checklist Running the HdswgFinal Setting of the Close Timer Maximum RUN TimerFinal Setting of the Motor Overload Sensitivity Installation Notes for Auxiliary Equipment Vehicle DetectorsGate Opener System Operation & Safety Guide Precautions for Pedestrian Traffic or Residential AreasMaintain the Gate and Gate Hardware a Gate Opener System Operation & SafetyMaintain ALL Components of Gate System Mechanical Unit Exploded View Hdswg 1000 Mechanical Unit Exploded ViewMechanical Unit Parts List ARM KIT & Control BOX Exploded View & PartsTechnical Specifications Physical DriveElectrical Capacities