Troubleshooting
Problem | Cause | Remedy | See | |
page | ||||
|
|
| ||
Only the center | When playing a monaural source with a |
|
| |
speaker outputs | CINEMA DSP program, the source signal |
|
| |
substantial sound. | is directed to the center channel, and the |
|
| |
| front and surround speakers output effect |
|
| |
| sounds. |
|
| |
|
|
|
| |
No sound is heard | “CENTER” in “SPEAKER SET” is set to | Set “CENTER” to “SML” or “LRG”. | 45 | |
from the center | “NONE”. |
|
| |
speaker. |
|
|
| |
Some sound field programs do not output | Try another sound field program. | 34 | ||
| ||||
| sounds from the center speaker. |
|
| |
|
|
|
| |
No sound is heard | “SUR. LR” in “SPEAKER SET” is set to | Set “SUR. LR” to “SML” or “LRG”. | 45 | |
from the surround | “NONE”. |
|
| |
speakers. |
|
|
| |
This unit is in the “STRAIGHT” mode | Press L STRAIGHT on the front panel so that | 36 | ||
| ||||
| and a monaural source is being played | “STRAIGHT” disappears from the front panel |
| |
| back. | display. |
| |
|
|
|
| |
No sound is heard | “BASS OUT” in “SPEAKER SET” is set | Set “BASS OUT” to “SWFR” or “BOTH”. | 46 | |
from the subwoofer. | to “FRNT” when a Dolby Digital or DTS |
|
| |
| signal is being played. |
|
| |
|
|
|
| |
| “BASS OUT” in “SPEAKER SET” is set | Set “BASS OUT” to “BOTH”. | 46 | |
| to “SWFR” or “FRNT” when a |
|
| |
| source is being played. |
|
| |
|
|
|
| |
| The source does not contain |
|
| |
|
|
| ||
|
|
|
| |
Dolby Digital or DTS | The connected component is not set to | Make an appropriate setting following the operating | — | |
sources cannot be | output Dolby Digital or DTS digital | instructions for your component. |
| |
played. (Dolby Digital | signals. |
|
| |
or DTS indicator in |
|
|
| |
Audio input jack select is set to | Set Audio input jack select to “AUTO”. | 31 | ||
the front panel | ||||
display does not light | “ANALOG”. |
|
| |
up.) |
|
|
| |
|
|
|
| |
A humming sound is | Incorrect cable connections. | Connect the audio cables firmly. If the problem | — | |
heard. |
| persists, the cables may be defective. |
| |
|
|
|
| |
The volume level | You are attempting to set the volume level | Adjust “MAX VOL.” setting. | 48 | |
cannot be increased, | higher than the maximum volume level. |
|
| |
or the sound is |
|
|
| |
The component connected to the AUDIO | Turn on the power of the component. | — | ||
distorted. | ||||
| OUT (REC) jacks on this unit is turned |
|
| |
| off. |
|
| |
|
|
|
| |
The sound effect | It is not possible to record the sound effect |
|
| |
cannot be recorded. | with a recording component. |
|
| |
|
|
|
| |
A source cannot be | The source component is not connected to | Connect the source component to the analog AUDIO | 15, 17 | |
recorded by an | the analog AUDIO IN jacks on this unit. | IN jacks. |
| |
analog component |
|
|
| |
connected to the |
|
|
| |
AUDIO OUT (REC) |
|
|
| |
jacks. |
|
|
| |
|
|
|
| |
The sound field | “MEM.GUARD” in “OPTION MENU” is | Set “MEM.GUARD” to “OFF”. | 50 | |
parameters and some | set to “ON”. |
|
| |
other settings of this |
|
|
| |
unit cannot be |
|
|
| |
changed. |
|
|
| |
|
|
|
|
This unit does not The internal microcomputer has been
operate properly. frozen by an external electric shock (such as lightning or excessive static electricity) or by a power supply with low voltage.
Disconnect the power cable from the AC wall outlet | — |
and then plug it in again after about 30 seconds. |
|
“CHECK SP WIRES” appears in the front panel display.
Speaker cables are | Make sure all speaker cables are connected correctly. | 11 |