Ricoh FV-L200B1 manual Descriptions of the Camera Control Commands

Page 25

4.4.2Descriptions of the Camera Control Commands

(The underline settings are the factory default settings)

Command No.

 

 

 

 

 

 

 

 

 

Command Descriptions

 

 

 

10H:

[Camera function mode setting 1] Initial data: 09H

 

 

 

MOD1[70]

This sets the following camera function mode.

 

 

 

 

 

 

 

D[70]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D7

D6

D5

D4

 

D3

D2

 

D1

 

D0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D7:

 

Continuous / Trigger Mode

 

0: Auto

 

1: Manual

 

 

D6:

 

Trigger Polarity

 

 

 

0: Positive

 

1: Negative

 

 

D5:

 

Trigger Mode

 

 

 

0: Edge Preset

 

1: Pulse Width

 

 

D4:

 

Binning Mode

 

 

 

0: OFF (Normal)

 

1: ON (Binning)

 

 

D3:

 

Scanning Mode

 

 

 

0: Full scanning

1: Partial scanning

 

 

D2 to D0:

Reset Mode

 

 

 

 

000: NonReset

001: VReset

 

 

 

 

 

 

 

 

 

 

 

010~111: No function

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Prohibited setting. Please do not use these)

 

When D7 is set to “0: Auto”, a camera will detect its operational mode based on the input trigger signal.

 

If the input trigger signal is kept at high, the camera operates in the continuous mode, assuming the trigger polarity

 

is set to positive.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11H:

[Camera function mode setting 2] Initial data: 0

 

 

 

 

 

 

MOD2[70]

This sets the following camera function modes.

 

 

 

 

 

 

 

D[70]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D7

D6

D5

D4

 

D3

D2

 

D1

 

D0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D7

 

HD / VD direction

 

 

00H: SP2 and SP3 as inputs

 

01H: SP2 and SP3 as outputs

 

 

 

 

 

 

 

 

 

 

10 to 11H: (Prohibited setting. Do not set these values)

 

 

D6 to D5

Frame rate

 

 

 

00H: 15.3 fps

 

01H:7.6 fps

 

 

 

 

 

 

 

 

 

 

10H: 3.8 fps

 

11H: No function

 

 

D4

 

Smear Half Reduction

0: OFF

 

1: ON

 

 

D3

 

Function Mode

 

 

0: Trigger Mode

 

1: Continuous Mode

 

 

D2 to D0:

Partial Scanning

 

 

000: Full scanning

 

001: 1/2 partial scanning

 

 

 

 

 

 

 

 

 

 

010: 1/4 partial scanning

 

111: Variable partial scanning

 

 

 

 

 

 

 

 

 

 

011~110: No function (Prohibited setting. Do not set these values)

 

Function mode is enabled when the “Continuous/Trigger” mode selection (MOD[7] is manual (set as 1).

 

No video output without the trigger signal input while the camera works with the trigger mode.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FVL200B1

25/32

User’s Guide Rev. 1.01

 

Image 25
Contents FVL200B1 User’s Guide Rev Uxga CCDTable of Contents Camera Link Connector Connector Specifications/ OUT PowerI/O ConnectorHorizontal Timing Normal Mode Setting 10HVertical Timing Normal Full Scanning Setting 10H 1XX00XXX, 11HPartial Full Scanning Settting 10H 1XX01XXX, 11H Partial Scanning Setting 10H 1XX01XXX, 11H SUB Variable Partial Scanning Setting 10H 1XX01XXX, 11HBinning Mode Setting 10H Setting 10H 1XX11XXX, 11H Setting 10H 1XX10XXX, 11HVertical Timing Binning Full Scanning Binning Partial Full ScanningBinning 1/4 Partial Scanning Setting 10H 1XX11XXX, 11H Binning 1/2 Partial Scanning Setting 10H 1XX11XXX, 11HData Order on the Camera Link Output 1TAP10bitPixel Transferring Image 1 Taps Transferring Image(1X1Y )Frame Exposure Normal ModeElectric Shutter Pulse Width Trigger Mode(VReset ) Pulse Width Trigger ModeExposure Timing Pulse Width Trigger Mode NonResetEdge Preset Trigger Mode VReset Edge Preset Trigger ModeEdge Preset Trigger Mode NonReset Reset Mode Communication Method Communication SettingsCommunication Format Name Descriptions 【Example Code】Reading the data from the command 00H Eeprom Camera Control Command Camera Command List24/32 Underline settings are the factory default settings Descriptions of the Camera Control Commands26/32 27/32 28/32 29/32 30/32 31/32 32/32