Ricoh FV-L200B1 manual 26/32

Page 26

Command No.

 

 

 

 

 

 

 

 

 

 

 

 

Command Descriptions

 

12H:

[Camera function mode setting 3] Initial data: 0

 

MOD3[70]

This sets the following camera function modes.

 

 

D[70]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D7

D6

 

D5

 

D4

 

D3

 

D2

D1

 

D0

 

 

 

 

D7~D6:

Video Out

 

 

 

 

 

 

00: 10bit

 

01: 8bit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10: 12bit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11: No function (Prohibited setting. Do not set these values)

 

 

D5:

 

Triggerin connector selection

0: Camera Link ( CC1)

1: /IO connector (No.2 Pin)

 

 

D4~D3:

Exposure Start Mode

 

 

00: Normal

01: Reserved trigger

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10 ~11: H reset

 

 

 

D2~D1:

No Function

 

 

 

 

Set always “000”

 

 

 

D0

 

Lookup table (Gamma)

 

00: OFF

01: ON

 

 

 

 

 

 

 

14H:

[Communication mode] Initial Data: 01H

 

 

 

 

 

UART[70]

This sets the communication modes.

 

 

 

 

 

 

D[70]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D7

D6

 

D5

 

D4

 

D3

 

D2

D1

 

D0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D7~D2:

 

No Function

 

 

 

Set always “000000”

 

 

 

D1~D0:

 

Communication Mode

 

00: 38,400 bps

01: 9,600 bps

 

 

 

 

 

 

 

 

 

 

 

 

 

10: 57,600 bps

11: 115,200 bps

 

 

 

1CH:

[AGC maximum limit] Initial data: 255, data range: 0 to 255

 

AGCMAX[7..0]

Sets the maximum limit for the AGC.

 

 

 

 

 

 

 

 

 

1DH:

[Target Brightness for ALC] Initial data: 128, data range: 0 to 255

 

ALCTRGT [7..0]

Sets the target brightness for the ALC function (Auto Luminance Control).

 

 

 

 

 

 

 

 

 

 

1EH:

[ALC mode] Initial data: 0

 

 

 

 

 

 

 

 

ALCMODE[7..0]

This sets the ALC modes.

 

 

 

 

 

 

 

 

 

D[70]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D7

D6

 

D5

 

D4

 

D3

 

D2

D1

 

D0

 

 

 

 

D7:

 

 

Long exposure

 

 

 

0: OFF

 

1: ON

 

 

D6 to D2 No Function

 

 

 

Set always “00000”

 

 

 

D1

 

 

AGC (Auto Gain Control)

0: OFF

1: ON

 

 

D0

 

 

AE (Auto Exposure)

 

0: OFF

1: ON

 

When using AE combined with the long exposure, exposure time is controlled regardless of the frame rate.

 

Therefore, the frame rate varies depending on the exposure time.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FVL200B1

26/32

User’s Guide Rev. 1.01

 

Image 26
Contents Uxga CCD FVL200B1 User’s Guide RevTable of Contents Connector Specifications Camera Link ConnectorPowerI/O Connector / OUTNormal Mode Setting 10H Horizontal TimingPartial Full Scanning Settting 10H 1XX01XXX, 11H Normal Full Scanning Setting 10H 1XX00XXX, 11HVertical Timing Partial Scanning Setting 10H 1XX01XXX, 11H Variable Partial Scanning Setting 10H 1XX01XXX, 11H SUBBinning Mode Setting 10H Vertical Timing Binning Full Scanning Setting 10H 1XX10XXX, 11HSetting 10H 1XX11XXX, 11H Binning Partial Full ScanningBinning 1/2 Partial Scanning Setting 10H 1XX11XXX, 11H Binning 1/4 Partial Scanning Setting 10H 1XX11XXX, 11H1TAP10bit Data Order on the Camera Link Output1 Taps Transferring Image(1X1Y ) Pixel Transferring ImageElectric Shutter Normal ModeFrame Exposure Pulse Width Trigger Mode Pulse Width Trigger Mode(VReset )Pulse Width Trigger Mode NonReset Exposure TimingEdge Preset Trigger Mode Edge Preset Trigger Mode VResetEdge Preset Trigger Mode NonReset Reset Mode Communication Format Communication SettingsCommunication Method Name Descriptions 【Example Code】Reading the data from the command 00H Camera Control Command Camera Command List Eeprom24/32 Descriptions of the Camera Control Commands Underline settings are the factory default settings26/32 27/32 28/32 29/32 30/32 31/32 32/32