Sanyo VCC-WB2000P Authentication, Circuit Type, Baud Rate, Data Size, Parity, Stop BIT

Page 25

Network Camera Settings

1AUTHENTICATION

This sets the verification protocol to be used when connecting to the access point. Set this to the protocol specified by the Internet Service Provider. It should normally be set to “AUTO”.

Available settings:

•AUTO: PAP or CHAP is chosen automatically as required

•PAP: Only PAP verification is used.

•CHAP: Only CHAP verification is used.

2CIRCUIT TYPE

This sets the type of telephone circuit that the modem is connecting to.

Available settings:

•TONE: For tone dialing circuits

•PULSE: For pulse dialing circuits

Note: Set to “TONE” if using a terminal adapter.

3BAUD RATE

This sets the communication speed for the modem.

Available settings: 115200, 38400 (bps)

4DATA SIZE

Available settings: 8, 7 (bits)

5PARITY

This sets the parity.

Available settings:

•NONE: No parity

•EVEN: Even parity

•ODD: Odd parity

6STOP BIT

Available settings: 1, 1.5, 2

7AUTO IP ADDRESS display

This shows the IP address for the camera.

Note: This is only displayed while the camera is connected.

8ERROR INFO. display

This shows error information relating to the previous PPP connection.

Display details:

•Modem timeout or Not connected

•Line connection error

•Line disconnected

•PPP connection error

•PPP authentication error

•PPP connected and disconnected normally

– 24 –

English

Image 25

Contents Network Camera VCC-WB2000PContents Precautions Accessories FeaturesOperating environment Power indicator Monitor OUT connectorName and Function of Each Part Lens mount capName and Function of Each Part Attach the CS mount-type lens Attaching the LensFor C mount type Turn on the camera’s power Flange Back AdjustmentBasic Connections ConnectionsRemoving the wireless LAN card Inserting the wireless LAN cardConnections PPP Dial-up Connections Network Camera Settings Installation of Plug-in Software Network Camera SettingsUninstalling the plug-in software Click the Install buttonClick the Finish button Cookie Settings Browser SettingsCamera uses cookies Language selection window Computer and Camera ConnectionsChanging Access Permissions Accessing Without Setting a PasswordClick the Network button Turn the camera off and then back on againClosing the initial window Network Connection SettingsSanyo Network CAMERA, the Unit is Click the Network button in the main menuID1 ID2 ID3 Network SET SettingsHttp Port Number Network SpeedCurrent Channel Wireless LAN SET SettingsEncryption KEY WEP EnciphermentType in the commands to use for controlling the modem PPP SET SettingsCircuit Type AuthenticationBaud Rate Data SizeAUTO/FINE radio buttons Menu Screen and Main MenuMenu Screen and Main Menu Opening and Closing the Initial Screen Viewing Camera ImagesViewing Camera Images When you have finished, click the network disconnect buttonSelect the language and then click the SET button Clock Unset indicator Live View SettingsClick the Live View button in the main menu Lit green NetcamResolution Expansion Live View SettingsSET button Image Mode settingCamera title display Live image screen displayClick the View Frame button in the main menu View Frame OperationsBack button Live Image Camera SettingsCamera Title IrisBright Camera SettingsElectronic Shutter White BalanceType in the new camera title e.g. CAM1 Setting the camera titleClick the SET button External Alarm Sensor Settings Alarm SettingClick the Alarm button in the main menu Change the External Alarm setting to NC or noAlarm Setting Picture Quality Motion Detector SET SettingsTime Expansion memory cards Alarm Data Recording CapacityInserting the memory card Removing the memory cardPlaying Back Alarm Data Recording Alarm DataClick the Alarm Data indicator while it is red or green Buffer Data View screen Playing Back Expansion Memory Card Images Deleting Alarm ImagesMessage the Unit is Loading Click the Delete buttonPre-alarm and Post-alarm Recording Daylight Saving Mode Clock SET SettingsClock SET TimezoneLanguage Selection RS-232C Settings RS-232C SETClick the RS-232C button in the main menu Click the Language button to change the languageClick the Status button in the main menu Status CheckingFirmware Version SUB-MICROCOMPUTER VersionIs the link indicator flashing? TroubleshootingIf the camera cannot be connected If you forget the IP AddressSpecifications Dimensions Specifications28 mm Page Printed on recycled paper 1AC6P1P2583 L5AB2/XE 0702KP-CZ