Sanyo VCC-WB2000P instruction manual Alarm Setting

Page 38

Alarm Setting

ID3

4 Set the following alarm recording settings as required.

When an alarm signal is input, the alarm data is stored in the camera’s memory.

•ALARM BUFFERING “ON”

•BUFFERING AREA

•PRIORITY

•ALARM RESOLUTION

•OVERWRITE

5 Once you have finished changing the settings, click the [SET] button.

If an outside intruder activates the infrared sensor, the ALARM indicator illuminates red on the live image screen. If a buzzer or lamp is connected to the ALARM OUT terminal, the buzzer will sound or the lamp will illuminate.

1EXTERNAL ALARM setting

This sets the polarity for the infrared sensor or similar that is connected to the ALARM IN terminal at the rear of the camera.

Available settings:

•OFF: No external alarm input is detected.

•NC: Normal close (normally closed, but input is detected when open).

•NO: Normal open (normally open, but input is detected when closed).

2MOTION DETECTOR setting

Set to “ON” when making motion detector settings. The MOTION DETECTOR SET screen will be displayed and you can then make settings such as sensitivity level.

3ALARM MODE setting

This sets if external alarm and/or motion sensor input triggers an alarm.

Available settings:

•AND: An alarm is generated when both the external alarm and the motion sensor receive alarm input.

•OR: An alarm is generated when either the external alarm or the motion sensor receives alarm input.

4ALARM OUT setting

This sets the polarity for the buzzer or lamp that is connected to the ALARM OUT terminal at the rear of the camera.

Available settings:

•OFF: No external alarm is output.

•NC: Normal close (normally closed, but an alarm is output when open).

•NO: Normal open (normally open, but an alarm is output when closed).

5ALARM TIME setting

This sets the duration of alarm output.

Available settings: 2 seconds to 5 minutes

Note: This setting is not the same as the

duration of alarm recording.

6ALARM BUFFERING setting

Set this to “ON” when alarm images are to be recorded.

7BUFFERING AREA setting

This sets the ratio between the amount of space for the memory areas used for recording pre-alarm and post-alarm images.

English

– 37 –

Image 38

Contents VCC-WB2000P Network CameraContents Precautions Features AccessoriesOperating environment Name and Function of Each Part Monitor OUT connectorPower indicator Lens mount capName and Function of Each Part For C mount type Attaching the LensAttach the CS mount-type lens Flange Back Adjustment Turn on the camera’s powerConnections Basic ConnectionsConnections Inserting the wireless LAN cardRemoving the wireless LAN card PPP Dial-up Connections Network Camera Settings Network Camera Settings Installation of Plug-in SoftwareClick the Finish button Click the Install buttonUninstalling the plug-in software Camera uses cookies Browser SettingsCookie Settings Computer and Camera Connections Language selection windowClick the Network button Accessing Without Setting a PasswordChanging Access Permissions Turn the camera off and then back on againSanyo Network CAMERA, the Unit is Network Connection SettingsClosing the initial window Click the Network button in the main menuNetwork SET Settings ID1 ID2 ID3Network Speed Http Port NumberWireless LAN SET Settings Current ChannelWEP Encipherment Encryption KEYPPP SET Settings Type in the commands to use for controlling the modemBaud Rate AuthenticationCircuit Type Data SizeMenu Screen and Main Menu AUTO/FINE radio buttonsMenu Screen and Main Menu Viewing Camera Images Opening and Closing the Initial ScreenSelect the language and then click the SET button When you have finished, click the network disconnect buttonViewing Camera Images Click the Live View button in the main menu Live View SettingsClock Unset indicator Lit green NetcamLive View Settings Resolution ExpansionCamera title display Image Mode settingSET button Live image screen displayBack button View Frame OperationsClick the View Frame button in the main menu Camera Title Camera SettingsLive Image Iris Electronic Shutter Camera Settings Bright White BalanceClick the SET button Setting the camera titleType in the new camera title e.g. CAM1 Click the Alarm button in the main menu Alarm SettingExternal Alarm Sensor Settings Change the External Alarm setting to NC or noAlarm Setting Time Motion Detector SET SettingsPicture Quality Inserting the memory card Alarm Data Recording CapacityExpansion memory cards Removing the memory cardClick the Alarm Data indicator while it is red or green Recording Alarm DataPlaying Back Alarm Data Buffer Data View screen Message the Unit is Loading Deleting Alarm ImagesPlaying Back Expansion Memory Card Images Click the Delete buttonPre-alarm and Post-alarm Recording Clock SET Clock SET SettingsDaylight Saving Mode TimezoneClick the RS-232C button in the main menu RS-232C Settings RS-232C SETLanguage Selection Click the Language button to change the languageFirmware Version Status CheckingClick the Status button in the main menu SUB-MICROCOMPUTER VersionIf the camera cannot be connected TroubleshootingIs the link indicator flashing? If you forget the IP AddressSpecifications 28 mm SpecificationsDimensions Page Printed on recycled paper 1AC6P1P2583 L5AB2/XE 0702KP-CZ