Sanyo VCC-WB2000P instruction manual Name and Function of Each Part

Page 7

Name and Function of Each Part

I

			PC CARD
	MONITOR	ETHERNET	H
8	OUT	ETHERNET	RS-232C
	OUT

G

COM

PC

POWER 1

2

MODEM

ALARM IN OUT

AC24VGND

DC12V

CLASS 2 WIRING

J 9 F

8Link indicator

This indicator illuminates when the camera is connected to a network. It flashes while data transmission is in progress.

9ALARM terminals

COM

B

A

C

ALARM IN OUT

AALARM IN terminal

Connect this terminal to an infrared sensor or similar use in external detection of intruders.

BALARM OUT terminal

Connect this terminal to a buzzer or lamp that is used to warn when the motion sensor detects an alarm.

CGround terminal (COM)

F24 V AC/12 V DC input terminals (AC24V, DC12V, GND)

GRS-232C connector

Use this connector to connect the camera to a modem for transmission of data along telephone lines, or for connecting the camera to a computer.

Use the PC/MODEM select switch to change the camera operation between modem and computer operation.

HETHERNET connector

Use this connector to connect the camera directly to a computer or to a network. Use a 10Base-T or 100Base-TX (Category 5, UTP) cable to make the connection.

ILens iris output connector

Connect this connector (4-pin socket) to the lens iris plug of the automatic iris-type lens (sold separately).

JPC/MODEM select switch

Use this switch to set the function of the RS-232C connector when connecting the camera directly to either a modem or computer.

Note:

•Make sure that the camera’s power is turned off before setting the function of the RS-232C connector.

•Using the RS-232C connector to connect the camera to a computer is only done for service purposes. You should not use this switch yourself.

– 6 –

English

Image 7

Contents Network Camera VCC-WB2000PContents Precautions Accessories FeaturesOperating environment Lens mount cap Monitor OUT connectorPower indicator Name and Function of Each PartName and Function of Each Part Attach the CS mount-type lens Attaching the LensFor C mount type Turn on the camera’s power Flange Back AdjustmentBasic Connections ConnectionsRemoving the wireless LAN card Inserting the wireless LAN cardConnections PPP Dial-up Connections Network Camera Settings Installation of Plug-in Software Network Camera SettingsUninstalling the plug-in software Click the Install buttonClick the Finish button Cookie Settings Browser SettingsCamera uses cookies Language selection window Computer and Camera ConnectionsTurn the camera off and then back on again Accessing Without Setting a PasswordChanging Access Permissions Click the Network buttonClick the Network button in the main menu Network Connection SettingsClosing the initial window Sanyo Network CAMERA, the Unit isID1 ID2 ID3 Network SET SettingsHttp Port Number Network SpeedCurrent Channel Wireless LAN SET SettingsEncryption KEY WEP EnciphermentType in the commands to use for controlling the modem PPP SET SettingsData Size AuthenticationCircuit Type Baud RateAUTO/FINE radio buttons Menu Screen and Main MenuMenu Screen and Main Menu Opening and Closing the Initial Screen Viewing Camera ImagesViewing Camera Images When you have finished, click the network disconnect buttonSelect the language and then click the SET button Lit green Netcam Live View SettingsClock Unset indicator Click the Live View button in the main menuResolution Expansion Live View SettingsLive image screen display Image Mode settingSET button Camera title displayClick the View Frame button in the main menu View Frame OperationsBack button Iris Camera SettingsLive Image Camera TitleWhite Balance Camera SettingsBright Electronic ShutterType in the new camera title e.g. CAM1 Setting the camera titleClick the SET button Change the External Alarm setting to NC or no Alarm SettingExternal Alarm Sensor Settings Click the Alarm button in the main menuAlarm Setting Picture Quality Motion Detector SET SettingsTime Removing the memory card Alarm Data Recording CapacityExpansion memory cards Inserting the memory cardPlaying Back Alarm Data Recording Alarm DataClick the Alarm Data indicator while it is red or green Buffer Data View screen Click the Delete button Deleting Alarm ImagesPlaying Back Expansion Memory Card Images Message the Unit is LoadingPre-alarm and Post-alarm Recording Timezone Clock SET SettingsDaylight Saving Mode Clock SETClick the Language button to change the language RS-232C Settings RS-232C SETLanguage Selection Click the RS-232C button in the main menuSUB-MICROCOMPUTER Version Status CheckingClick the Status button in the main menu Firmware VersionIf you forget the IP Address TroubleshootingIs the link indicator flashing? If the camera cannot be connectedSpecifications Dimensions Specifications28 mm Page Printed on recycled paper 1AC6P1P2583 L5AB2/XE 0702KP-CZ