Transcend Information 400X, TS16G-64GCF400 dimensions Name Comment

Page 35

TS16G~64GCF400

400X CompactFlash Card

 

 

 

4)The parameter tLI shall be measured at the connector of the sender or recipient that is responding to an incoming transition from the recipient or sender respectively. Both the incoming signal and the outgoing response shall be measured at the same connector.

5)The parameter tAZ shall be measured at the connector of the sender or recipient that is driving the bus but must release the bus the allow for a bus turnaround.

Name

Comment

t2CYCTYP

Typical sustained average two cycle time

 

 

tCYC

Cycle time allowing for asymmetry and clock variations (from STROBE edge to STROBE edge)

t2CYC

Two cycle time allowing for clock variations (from rising edge to next rising edge or from falling edge to

next falling edge of STROBE)

 

tDS

Data setup time at recipient (from data valid until STROBE edge)

tDH

Data hold time at recipient (from STROBE edge until data may become invalid)

tDVS

Data valid setup time at sender (from data valid until STROBE edge)

tDVH

Data valid hold time at sender (from STROBE edge until data may become invalid)

tCS

CRC word setup time at device

 

 

tCH

CRC word hold time device

 

 

tCVS

CRC word valid setup time at host (from CRC valid until -DMACK negation)

tCVH

CRC word valid hold time at sender (from -DMACK negation until CRC may become invalid)

tZFS

Time from STROBE output released-to-driving until the first transition of critical timing.

tDZFS

Time from data output released-to-driving until the first transition of critical timing.

tFS

First STROBE time (for device to first negate DSTROBE from STOP during a data in burst)

tLI

Limited interlock time

tMLI

Interlock time with minimum

tUI

Unlimited interlock time

tAZ

Maximum time allowed for output drivers to release (from asserted or negated)

tZAH

Minimum delay time required for output

tZAD

drivers to assert or negate (from released)

tENV

Envelope time (from -DMACK to STOP and -HDMARDY during data in burst initiation and from DMACK

to STOP during data out burst initiation)

 

tRFS

Ready-to-final-STROBE time (no STROBE edges shall be sent this long after negation of -DMARDY)

tRP

Ready-to-pause time (that recipient shall wait to pause after negating -DMARDY)

tIORDYZ

Maximum time before releasing IORDY

tZIORDY

Minimum time before driving IORDY

tACK

Setup and hold times for -DMACK (before assertion or negation)

tSS

Time from STROBE edge to negation of DMARQ or assertion of STOP (when sender terminates a

burst)

 

 

 

Notes

2, 5 2, 5 3 3 2 2 3 3

1

1

1

6 4, 6

Transcend Information Inc.

35

V1.0

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Description Placement FeaturesDimensions Specification Model P/N User LBA Cylinder Head Sector PerformanceActual Capacity Model P/NBlock Diagram TS16G~64GCF400 True IDE Mode4 PC Card Memory Mode PC Card I/O ModePin Assignments and Pin Type PC Card Memory Mode PC Card I/O Mode True IDE Mode4 Output Drive Type Input CharacteristicsInput Leakage Current Type Parameter Symbol Conditions Output Drive CharacteristicsOutput Drive Characteristics Stschg Signal DescriptionSignal Name Dir Pin Description 400X CompactFlash CardGND CselPin Description Signal NameDir Intrq StopReady Dmack ResetREG Dstrobe WaitIordy DdmardyCompactFlash Interface I/O at Electrical SpecificationUnits Input Power Input Characteristics for Udma modeParameter Symbol Output Drive Characteristics for Udma modeSignal Card10 Host10 Signal Interface150 a high state per socket LowPull-up pin 45 BVD2 to avoid sensing their batteries as Low Low stateTable Typical Series Termination for Ultra DMA Ultra DMA Electrical RequirementsSeries termination required for Ultra DMA operation Ultra DMA Mode Cabling Requirement Speed Version Attribute Memory Read Timing SpecificationSymbol Ieee Symbol Min ns Max nsSpeed Version 250 ns Symbol Min ns Max ns Table Configuration Register Attribute Memory Write Timing250 ns 120 ns 100 ns 80 ns Min Common Memory Read Timing SpecificationCycle Time Mode Ieee100 ns Min Common Memory Write Timing SpecificationCycle Time Mode 250 ns Symbol Symbol 120 ns MinMin Max Symbol Input Read Timing SpecificationCycle Time Mode 250 ns 120 ns 100 ns 80 ns TsuHIOW TDVIWH ThHIOW TlWHDX TwHIOW TlWLIWH Output Write Timing SpecificationCycle Time Mode 255 ns 120 ns 100 ns 80 ns T6Z True IDE PIO Mode Read/Write Timing SpecificationMode TS16G~64GCF400 True IDE Multiword DMA Mode Read/Write Timing Specification True IDE Ultra DMA Mode Read/Write Timing Specification Pin # Non PC Card MEM PC Card IO Mode True IDE ModeUdma Signal Type Mode UdmaTS16G~64GCF400 Name Name Comment 14.7 Name Mode Mode4Udma Min MaxFalling Edge Slew Rate for any signal Rising Edge Slew Rate for any signalSelected Space Card ConfigurationMultiple Function CompactFlash Storage Cards REGInpack REG Stop Dmardy Strobe Dmarq Dmack HioeDMA HIODMA CMD REG Function ModeAttribute Memory Function Table Attribute Memory FunctionConfiguration Option Register Base + 00h in Attribute Memory TS16G~64GCF400 Pin Replacement Register Base + 04h in Attribute Memory Socket and Copy Register Base + 06h in Attribute Memory Hioe Hiow Table Pcmcia Mode I/O FunctionTransfer Function DMA REGInpack REG Hiow Table PC Card I/O Mode Udma FunctionDmardy Strobe Dmarq Dmack Stop Hioe Wait DMA A10CE2 CE1 D15-D8 D7-D0 Common Memory Transfer FunctionTable Common Memory Function True IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol Table Primary and Secondary I/O Decoding Primary and Secondary Address ConfigurationsTable Contiguous I/O Decoding Contiguous I/O Mapped AddressingMemory Mapped Addressing True IDE Mode AddressingData Register Address 1F0h170hOffset 0,8,9 CF-ATA RegistersCylinder Low LBA 15-8 Register Address 1F4h174h Offset Feature Register Address 1F1h171h Offset 1, 0Dh Write OnlySector Count Register Address 1F2h172h Offset Sector Number LBA 7-0 Register Address 1F3h173h OffsetTS16G~64GCF400 Device Control Register Address 3F6h376h Offset Eh Card Drive Address Register Address 3F7h377h Offset Fh Command Code CF-ATA Command SetDefinitions Cyl High Cyl Low Sec Num Sec Cnt Feature Check Power Mode 98h or E5hExecute Drive Diagnostic 90h Bit CommandFormat Track 50h Transcend Information IncErase Sectors C0h Flush Cache E7hBytes Drive Cyl High Cyl Low Sec Num Sec Cnt FeatureWord Default Total Data Field Type Information Identify Device EchDefault Total Data Field Type Information 162 0000h Key management schemes supported 163 Word 0 General ConfigurationWord 1 Default Number of Cylinders CF Advanced True IDE Timing Mode Capability and Setting 164PIO Data Transfer Cycle Timing Mode Word 3 Default Number of HeadsWord 6 Default Number of Sectors per Track Word 49 Capabilities Bit 13 Standby TimerMultiword DMA transfer Multiple Sector SettingTotal Sectors Addressable in LBA Mode Current CapacityWord 68 Minimum PIO transfer cycle time with Iordy Words 82-84 Features/command sets supportedWord 88 Ultra DMA Modes Supported and Selected Words 85-87 Features/command sets enabledWord 128 Security Status Bit 8 Security Level Word 91 Advanced power management level valueWord 160 Power Requirement Description Word 89 Time required for Security erase unit completionAdditional Requirements for CF Advanced Timing Modes Value Current PIO timing mode selectedMaximum PIO mode timing selected Maximum Multiword DMA timing mode supportedMaximum Memory timing mode Supported Value Current Multiword DMA timing mode selectedMaximum Pcmcia IO timing mode Supported Value PC Card Memory or I/O Udma timing mode Selected Value Maximum PC Card I/O Udma timing mode SupportedValue Maximum PC Card Memory Udma timing mode Supported NOP 00h Idle 97h or E3hIdle Immediate 95h or E1h Initialize Drive Parameters 91hRead DMA C8h Read Long Sector 22h or 23h Read Buffer E4hTS16G~64GCF400 Request Sense 03h Seek 7Xh Set Features EFhFeature Supported TS16G~64GCF400 Translate Sector Information Standby Immediate 94h or E0h Translate Sector 87hWear Level F5h Write Buffer E8h Write DMA CAh TS16G~64GCF400 TS16G~64GCF400 BBK Error PostingError Register Status Register NOPBBK UNC Idnf Abrt Amnf Drdy DWF DSC Corr ERR Description Smart Command SetSmart Command Set Smart Feature Register Values Smart Data StructureSMI CompactFlash Card Ordering InformationTranscend Product Capacity

TS16G-64GCF400, 400X specifications

The Transcend Information TS16G-64GCF400, 400X is a high-performance CompactFlash card designed specifically to meet the demanding requirements of professionals in photography, video production, and data-intensive applications. With a capacity of 64GB and boasting an impressive transfer speed of up to 400X, the TS16G-64GCF400 is ideal for those seeking reliability and efficiency when recording high-resolution images and videos.

One of the standout features of this CompactFlash card is its exceptional read and write speeds. The card can achieve read speeds of up to 90 MB/s and write speeds that can reach up to 60 MB/s. These performance metrics make the TS16G-64GCF400 particularly suitable for burst shooting and continuous video recording, ensuring that every moment is captured accurately and without lag.

In terms of technology, the card utilizes advanced flash memory technology to enhance both speed and durability. Built with a robust construction, it is designed to withstand extreme conditions, making it resistant to shock, temperature fluctuations, and high humidity. This resilience is particularly important for users who often work in unpredictable environments or travel frequently.

The TS16G-64GCF400 is also equipped with the Ultra DMA mode, allowing for faster data transfer between the card and the camera or device it is used with. It supports both PIO and multi-word DMA modes, ensuring compatibility with a wide range of devices. Furthermore, it adheres to the CompactFlash Association's CF4.1 specifications, ensuring that users can rely on its performance across a variety of applications.

Another characteristic worth mentioning is the card's data security features. The Transcend TS16G-64GCF400 incorporates Error Correction Code (ECC) technology to detect and correct potential data corruption, ensuring that files remain intact over time. Additionally, it has built-in wear leveling technology to promote the distribution of write and erase cycles evenly across the memory cells, ultimately prolonging the lifespan of the card.

In conclusion, the Transcend Information TS16G-64GCF400, 400X CompactFlash card stands out in the competitive market of storage solutions. With its impressive speed, durability, and advanced features, it is an excellent choice for professional photographers and videographers who demand high performance and reliability in their storage devices. Whether capturing the next big moment or storing essential data, this card is sure to deliver the performance users need.
Top Page Image Contents