Transcend Information TS16G-64GCF400 CF-ATA Registers, Data Register Address 1F0h170hOffset 0,8,9

Page 54

TS16G~64GCF400

400X CompactFlash Card

 

 

 

￿CF-ATA Registers

The following section describes the hardware registers used by the host software to issue commands to the CompactFlash device. These registers are often collectively referred to as the “task file.”

￿Data Register (Address - 1F0h[170h];Offset 0,8,9)

The Data Register is a 16 bit register, and it is used to transfer data blocks between the CompactFlash Storage Card data buffer and the Host. This register overlaps the Error Register.

Error Register (Address - 1F1h[171h]; Offset 1, 0Dh Read Only)

This register contains additional information about the source of an error when an error is indicated in bit 0 of the Status register.

This register is also accessed in PC Card Modes on data bits D15-D8 during a read operation to offset 0 with -CE2 low and -CE1 high.

Bit 7 (BBK/ICRC): this bit is set when a Bad Block is detected. This bit is also set when an interface CRC error is detected in True IDE Ultra DMA modes of operation.

Bit 6 (UNC): this bit is set when an Uncorrectable Error is encountered.

Bit 5: this bit is 0.

Bit 4 (IDNF): the requested sector ID is in error or cannot be found.

Bit 3: this bit is 0.

Bit 2 (Abort) This bit is set if the command has been aborted because of a CompactFlash Storage Card status condition: (Not Ready, Write Fault, etc.) or when an invalid command has been issued.

Bit 1 This bit is 0.

Bit 0 (AMNF) This bit is set in case of a general error.

Transcend Information Inc.

54

V1.0

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Placement Features DimensionsDescription Specification Model P/N PerformanceActual Capacity Model P/N User LBA Cylinder Head SectorBlock Diagram TS16G~64GCF400 PC Card Memory Mode PC Card I/O Mode Pin Assignments and Pin TypeTrue IDE Mode4 PC Card Memory Mode PC Card I/O Mode True IDE Mode4 Input Characteristics Input Leakage CurrentOutput Drive Type Output Drive Characteristics Output Drive CharacteristicsType Parameter Symbol Conditions 400X CompactFlash Card Signal DescriptionSignal Name Dir Pin Description StschgCsel GNDSignal Name DirPin Description Stop ReadyIntrq Reset REGDmack Ddmardy WaitIordy DstrobeElectrical Specification CompactFlash Interface I/O atOutput Drive Characteristics for Udma mode Input Power Input Characteristics for Udma modeParameter Symbol UnitsSignal Interface Signal Card10 Host10Low state LowPull-up pin 45 BVD2 to avoid sensing their batteries as Low 150 a high state per socketUltra DMA Electrical Requirements Series termination required for Ultra DMA operationTable Typical Series Termination for Ultra DMA Ultra DMA Mode Cabling Requirement Ieee Symbol Min ns Max ns Attribute Memory Read Timing SpecificationSymbol Speed VersionTable Configuration Register Attribute Memory Write Timing Speed Version 250 ns Symbol Min ns Max nsIeee Common Memory Read Timing SpecificationCycle Time Mode 250 ns 120 ns 100 ns 80 ns MinSymbol 120 ns Min Common Memory Write Timing SpecificationCycle Time Mode 250 ns Symbol 100 ns MinInput Read Timing Specification Cycle Time Mode 250 ns 120 ns 100 ns 80 nsMin Max Symbol Output Write Timing Specification Cycle Time Mode 255 ns 120 ns 100 ns 80 nsTsuHIOW TDVIWH ThHIOW TlWHDX TwHIOW TlWLIWH True IDE PIO Mode Read/Write Timing Specification ModeT6Z TS16G~64GCF400 True IDE Multiword DMA Mode Read/Write Timing Specification True IDE Ultra DMA Mode Read/Write Timing Specification Mode Udma PC Card MEM PC Card IO Mode True IDE ModeUdma Signal Type Pin # NonTS16G~64GCF400 Name Name Comment Min Max Name Mode Mode4Udma 14.7Rising Edge Slew Rate for any signal Falling Edge Slew Rate for any signalREG Card ConfigurationMultiple Function CompactFlash Storage Cards Selected SpaceHIO Stop Dmardy Strobe Dmarq Dmack HioeDMA Inpack REGTable Attribute Memory Function Function ModeAttribute Memory Function DMA CMD REGConfiguration Option Register Base + 00h in Attribute Memory TS16G~64GCF400 Pin Replacement Register Base + 04h in Attribute Memory Socket and Copy Register Base + 06h in Attribute Memory DMA REG Table Pcmcia Mode I/O FunctionTransfer Function Hioe HiowDmarq Dmack Stop Hioe Wait DMA A10 Table PC Card I/O Mode Udma FunctionDmardy Strobe Inpack REG HiowCommon Memory Transfer Function Table Common Memory FunctionCE2 CE1 D15-D8 D7-D0 True IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol Primary and Secondary Address Configurations Table Primary and Secondary I/O DecodingContiguous I/O Mapped Addressing Table Contiguous I/O DecodingTrue IDE Mode Addressing Memory Mapped AddressingCF-ATA Registers Data Register Address 1F0h170hOffset 0,8,9Sector Number LBA 7-0 Register Address 1F3h173h Offset Feature Register Address 1F1h171h Offset 1, 0Dh Write OnlySector Count Register Address 1F2h172h Offset Cylinder Low LBA 15-8 Register Address 1F4h174h OffsetTS16G~64GCF400 Device Control Register Address 3F6h376h Offset Eh Card Drive Address Register Address 3F7h377h Offset Fh CF-ATA Command Set Command CodeDefinitions Bit Command Check Power Mode 98h or E5hExecute Drive Diagnostic 90h Cyl High Cyl Low Sec Num Sec Cnt FeatureFlush Cache E7h Transcend Information IncErase Sectors C0h Format Track 50hIdentify Device Ech Drive Cyl High Cyl Low Sec Num Sec Cnt FeatureWord Default Total Data Field Type Information BytesDefault Total Data Field Type Information CF Advanced True IDE Timing Mode Capability and Setting 164 Word 0 General ConfigurationWord 1 Default Number of Cylinders 162 0000h Key management schemes supported 163Word 49 Capabilities Bit 13 Standby Timer Word 3 Default Number of HeadsWord 6 Default Number of Sectors per Track PIO Data Transfer Cycle Timing ModeCurrent Capacity Multiple Sector SettingTotal Sectors Addressable in LBA Mode Multiword DMA transferWords 82-84 Features/command sets supported Word 68 Minimum PIO transfer cycle time with IordyWords 85-87 Features/command sets enabled Word 88 Ultra DMA Modes Supported and SelectedWord 89 Time required for Security erase unit completion Word 91 Advanced power management level valueWord 160 Power Requirement Description Word 128 Security Status Bit 8 Security LevelMaximum Multiword DMA timing mode supported Value Current PIO timing mode selectedMaximum PIO mode timing selected Additional Requirements for CF Advanced Timing ModesValue Current Multiword DMA timing mode selected Maximum Pcmcia IO timing mode SupportedMaximum Memory timing mode Supported Value Maximum PC Card I/O Udma timing mode Supported Value Maximum PC Card Memory Udma timing mode SupportedValue PC Card Memory or I/O Udma timing mode Selected Initialize Drive Parameters 91h Idle 97h or E3hIdle Immediate 95h or E1h NOP 00hRead Buffer E4h Read DMA C8h Read Long Sector 22h or 23hTS16G~64GCF400 Seek 7Xh Set Features EFh Request Sense 03hFeature Supported TS16G~64GCF400 Standby Immediate 94h or E0h Translate Sector 87h Translate Sector InformationWear Level F5h Write Buffer E8h Write DMA CAh TS16G~64GCF400 TS16G~64GCF400 NOP Error PostingError Register Status Register BBKBBK UNC Idnf Abrt Amnf Drdy DWF DSC Corr ERR Smart Data Structure Smart Command SetSmart Command Set Smart Feature Register Values DescriptionSMI Ordering Information Transcend Product CapacityCompactFlash Card

TS16G-64GCF400, 400X specifications

The Transcend Information TS16G-64GCF400, 400X is a high-performance CompactFlash card designed specifically to meet the demanding requirements of professionals in photography, video production, and data-intensive applications. With a capacity of 64GB and boasting an impressive transfer speed of up to 400X, the TS16G-64GCF400 is ideal for those seeking reliability and efficiency when recording high-resolution images and videos.

One of the standout features of this CompactFlash card is its exceptional read and write speeds. The card can achieve read speeds of up to 90 MB/s and write speeds that can reach up to 60 MB/s. These performance metrics make the TS16G-64GCF400 particularly suitable for burst shooting and continuous video recording, ensuring that every moment is captured accurately and without lag.

In terms of technology, the card utilizes advanced flash memory technology to enhance both speed and durability. Built with a robust construction, it is designed to withstand extreme conditions, making it resistant to shock, temperature fluctuations, and high humidity. This resilience is particularly important for users who often work in unpredictable environments or travel frequently.

The TS16G-64GCF400 is also equipped with the Ultra DMA mode, allowing for faster data transfer between the card and the camera or device it is used with. It supports both PIO and multi-word DMA modes, ensuring compatibility with a wide range of devices. Furthermore, it adheres to the CompactFlash Association's CF4.1 specifications, ensuring that users can rely on its performance across a variety of applications.

Another characteristic worth mentioning is the card's data security features. The Transcend TS16G-64GCF400 incorporates Error Correction Code (ECC) technology to detect and correct potential data corruption, ensuring that files remain intact over time. Additionally, it has built-in wear leveling technology to promote the distribution of write and erase cycles evenly across the memory cells, ultimately prolonging the lifespan of the card.

In conclusion, the Transcend Information TS16G-64GCF400, 400X CompactFlash card stands out in the competitive market of storage solutions. With its impressive speed, durability, and advanced features, it is an excellent choice for professional photographers and videographers who demand high performance and reliability in their storage devices. Whether capturing the next big moment or storing essential data, this card is sure to deliver the performance users need.
Top Page Image Contents