Transcend Information 400X Word 0 General Configuration, Word 1 Default Number of Cylinders

Page 65

TS16G~64GCF400

 

400X CompactFlash Card

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

162

0000h

 

2

Key management schemes supported

 

 

 

 

 

 

 

 

 

163

0092h

 

2

CF Advanced True IDE Timing Mode Capability and Setting

 

 

 

 

 

 

 

 

 

164

8D9Bh

 

2

CF Advanced PC Card I/O and Memory Timing Mode Capability

 

 

 

 

 

 

 

 

 

165-175

0000h

 

22

Reserved

 

 

 

 

 

 

 

 

 

176-255

0000h

 

140

Reserved

 

 

 

 

 

 

 

 

 

￿Word 0: General Configuration

This field indicates the general characteristics of the device. When Word 0 of the Identify drive information is 848Ah then the device is a CompactFlash Storage Card and complies with the CFA specification and CFA command set. It is recommended that PCMCIA modes of operation report only the 848Ah value as they are always intended as removable devices.

Bits 15-0: CF Standard Configuration Value

Word 0 is 848Ah. This is the recommended value of Word 0.

Some operating systems require Bit 6 of Word 0 to be set to 1 (Non-removable device) to use the card as the root storage device. The Card must be the root storage device when a host completely replaces conventional disk storage with a CompactFlash Card in True IDE mode. To support this requirement and provide capability for any future removable media Cards, alternatehandling of Word 0 is permitted.

Bits 15-0: CF Preferred Alternate Configuration Values

044Ah: This is the alternate value of Word 0 turns on ATA device and turns off Removable Media and Removable Device while preserving all Retired bits in the word.

0040h: This is the alternate value of Word 0 turns on ATA device and turns off Removable Media and Removable Device while zeroing all Retired bits in the word

Bit 15-12: Configuration Flag

If bits 15:12 are set to 8h then Word 0 shall be 848Ah.

If bits 15:12 are set to 0h then Bits 11:0 are set using the definitions below and the Card is required to support for the CFA command set and report that in bit 2 of Word 83.

Bit 15:12 values other than 8h and 0h are prohibited.

Bits 11-8: Retired

These bits have retired ATA bit definitions. It is recommended that the value of these bits be either the preferred value of 0h or the value of 4h that preserves the corresponding bits from the 848Ah CF signature value.

Bit 7: Removable Media Device

If Bit 7 is set to 1, the Card contains media that can be removed during Card operation.

If Bit 7 is set to 0, the Card contains nonremovable media.

Bit 6: Not Removable Controller and/or Device

Alert! This bit will be considered for obsolescence in a future revision of this standard.

If Bit 6 is set to 1, the Card is intended to be nonremovable during operation.

If Bit 6 is set to 0, the Card is intended to be removable during operation.

Bits 5-0: Retired/Reserved

Alert! Bit 2 will be considered for definition in a future revision of this standard and shall be 0 at this time.

Bits 5-1 have retired ATA bit definitions. Bit 2 shall be 0.

Bit 0 is Reserved and shall be 0.

It is recommended that the value of bits 5-0 be either the preferred value of 00h or the value of 0Ah that preserves the corresponding bits from the 848Ah CF signature value.

￿Word 1: Default Number of Cylinders

This field contains the number of translated cylinders in the default translation mode. This value will be the

Transcend Information Inc.

65

V1.0

Page 64 Page 66
Image 65
Page 64 Page 66
Contents Description Placement FeaturesDimensions Specification Actual Capacity PerformanceModel P/N Model P/N User LBA Cylinder Head SectorBlock Diagram TS16G~64GCF400 True IDE Mode4 PC Card Memory Mode PC Card I/O ModePin Assignments and Pin Type PC Card Memory Mode PC Card I/O Mode True IDE Mode4 Output Drive Type Input CharacteristicsInput Leakage Current Type Parameter Symbol Conditions Output Drive CharacteristicsOutput Drive Characteristics Signal Name Dir Pin Description Signal Description400X CompactFlash Card StschgGND CselPin Description Signal NameDir Intrq StopReady Dmack ResetREG Iordy WaitDdmardy DstrobeCompactFlash Interface I/O at Electrical SpecificationParameter Symbol Input Power Input Characteristics for Udma modeOutput Drive Characteristics for Udma mode UnitsSignal Card10 Host10 Signal InterfacePull-up pin 45 BVD2 to avoid sensing their batteries as Low LowLow state 150 a high state per socketTable Typical Series Termination for Ultra DMA Ultra DMA Electrical RequirementsSeries termination required for Ultra DMA operation Ultra DMA Mode Cabling Requirement Symbol Attribute Memory Read Timing SpecificationIeee Symbol Min ns Max ns Speed VersionSpeed Version 250 ns Symbol Min ns Max ns Table Configuration Register Attribute Memory Write TimingCycle Time Mode Common Memory Read Timing SpecificationIeee 250 ns 120 ns 100 ns 80 ns MinCycle Time Mode 250 ns Symbol Common Memory Write Timing SpecificationSymbol 120 ns Min 100 ns MinMin Max Symbol Input Read Timing SpecificationCycle Time Mode 250 ns 120 ns 100 ns 80 ns TsuHIOW TDVIWH ThHIOW TlWHDX TwHIOW TlWLIWH Output Write Timing SpecificationCycle Time Mode 255 ns 120 ns 100 ns 80 ns T6Z True IDE PIO Mode Read/Write Timing SpecificationMode TS16G~64GCF400 True IDE Multiword DMA Mode Read/Write Timing Specification True IDE Ultra DMA Mode Read/Write Timing Specification Udma Signal Type PC Card MEM PC Card IO Mode True IDE ModeMode Udma Pin # NonTS16G~64GCF400 Name Name Comment Udma Name Mode Mode4Min Max 14.7Falling Edge Slew Rate for any signal Rising Edge Slew Rate for any signalMultiple Function CompactFlash Storage Cards Card ConfigurationREG Selected SpaceDMA Stop Dmardy Strobe Dmarq Dmack HioeHIO Inpack REGAttribute Memory Function Function ModeTable Attribute Memory Function DMA CMD REGConfiguration Option Register Base + 00h in Attribute Memory TS16G~64GCF400 Pin Replacement Register Base + 04h in Attribute Memory Socket and Copy Register Base + 06h in Attribute Memory Transfer Function Table Pcmcia Mode I/O FunctionDMA REG Hioe HiowDmardy Strobe Table PC Card I/O Mode Udma FunctionDmarq Dmack Stop Hioe Wait DMA A10 Inpack REG HiowCE2 CE1 D15-D8 D7-D0 Common Memory Transfer FunctionTable Common Memory Function True IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol Table Primary and Secondary I/O Decoding Primary and Secondary Address ConfigurationsTable Contiguous I/O Decoding Contiguous I/O Mapped AddressingMemory Mapped Addressing True IDE Mode AddressingData Register Address 1F0h170hOffset 0,8,9 CF-ATA RegistersSector Count Register Address 1F2h172h Offset Feature Register Address 1F1h171h Offset 1, 0Dh Write OnlySector Number LBA 7-0 Register Address 1F3h173h Offset Cylinder Low LBA 15-8 Register Address 1F4h174h OffsetTS16G~64GCF400 Device Control Register Address 3F6h376h Offset Eh Card Drive Address Register Address 3F7h377h Offset Fh Command Code CF-ATA Command SetDefinitions Execute Drive Diagnostic 90h Check Power Mode 98h or E5hBit Command Cyl High Cyl Low Sec Num Sec Cnt FeatureErase Sectors C0h Transcend Information IncFlush Cache E7h Format Track 50hWord Default Total Data Field Type Information Drive Cyl High Cyl Low Sec Num Sec Cnt FeatureIdentify Device Ech BytesDefault Total Data Field Type Information Word 1 Default Number of Cylinders Word 0 General ConfigurationCF Advanced True IDE Timing Mode Capability and Setting 164 162 0000h Key management schemes supported 163Word 6 Default Number of Sectors per Track Word 3 Default Number of HeadsWord 49 Capabilities Bit 13 Standby Timer PIO Data Transfer Cycle Timing ModeTotal Sectors Addressable in LBA Mode Multiple Sector SettingCurrent Capacity Multiword DMA transferWord 68 Minimum PIO transfer cycle time with Iordy Words 82-84 Features/command sets supportedWord 88 Ultra DMA Modes Supported and Selected Words 85-87 Features/command sets enabledWord 160 Power Requirement Description Word 91 Advanced power management level valueWord 89 Time required for Security erase unit completion Word 128 Security Status Bit 8 Security LevelMaximum PIO mode timing selected Value Current PIO timing mode selectedMaximum Multiword DMA timing mode supported Additional Requirements for CF Advanced Timing ModesMaximum Memory timing mode Supported Value Current Multiword DMA timing mode selectedMaximum Pcmcia IO timing mode Supported Value PC Card Memory or I/O Udma timing mode Selected Value Maximum PC Card I/O Udma timing mode SupportedValue Maximum PC Card Memory Udma timing mode Supported Idle Immediate 95h or E1h Idle 97h or E3hInitialize Drive Parameters 91h NOP 00hRead DMA C8h Read Long Sector 22h or 23h Read Buffer E4hTS16G~64GCF400 Request Sense 03h Seek 7Xh Set Features EFhFeature Supported TS16G~64GCF400 Translate Sector Information Standby Immediate 94h or E0h Translate Sector 87hWear Level F5h Write Buffer E8h Write DMA CAh TS16G~64GCF400 TS16G~64GCF400 Error Register Status Register Error PostingNOP BBKBBK UNC Idnf Abrt Amnf Drdy DWF DSC Corr ERR Smart Command Set Smart Feature Register Values Smart Command SetSmart Data Structure DescriptionSMI CompactFlash Card Ordering InformationTranscend Product Capacity

TS16G-64GCF400, 400X specifications

The Transcend Information TS16G-64GCF400, 400X is a high-performance CompactFlash card designed specifically to meet the demanding requirements of professionals in photography, video production, and data-intensive applications. With a capacity of 64GB and boasting an impressive transfer speed of up to 400X, the TS16G-64GCF400 is ideal for those seeking reliability and efficiency when recording high-resolution images and videos.

One of the standout features of this CompactFlash card is its exceptional read and write speeds. The card can achieve read speeds of up to 90 MB/s and write speeds that can reach up to 60 MB/s. These performance metrics make the TS16G-64GCF400 particularly suitable for burst shooting and continuous video recording, ensuring that every moment is captured accurately and without lag.

In terms of technology, the card utilizes advanced flash memory technology to enhance both speed and durability. Built with a robust construction, it is designed to withstand extreme conditions, making it resistant to shock, temperature fluctuations, and high humidity. This resilience is particularly important for users who often work in unpredictable environments or travel frequently.

The TS16G-64GCF400 is also equipped with the Ultra DMA mode, allowing for faster data transfer between the card and the camera or device it is used with. It supports both PIO and multi-word DMA modes, ensuring compatibility with a wide range of devices. Furthermore, it adheres to the CompactFlash Association's CF4.1 specifications, ensuring that users can rely on its performance across a variety of applications.

Another characteristic worth mentioning is the card's data security features. The Transcend TS16G-64GCF400 incorporates Error Correction Code (ECC) technology to detect and correct potential data corruption, ensuring that files remain intact over time. Additionally, it has built-in wear leveling technology to promote the distribution of write and erase cycles evenly across the memory cells, ultimately prolonging the lifespan of the card.

In conclusion, the Transcend Information TS16G-64GCF400, 400X CompactFlash card stands out in the competitive market of storage solutions. With its impressive speed, durability, and advanced features, it is an excellent choice for professional photographers and videographers who demand high performance and reliability in their storage devices. Whether capturing the next big moment or storing essential data, this card is sure to deliver the performance users need.
Top Page Image Contents