Transcend Information 400X, TS16G-64GCF400 dimensions Metaformat Overview

Page 49

TS16G~64GCF400

400X CompactFlash Card

 

 

 

Host Configuration Requirements for Master/Slave or New Timing Modes

The CF Advanced Timing modes include PCMCIA PC Card style I/O modes that are faster than the original 250 ns cycle time. These modes are not supported by the PCMCIA PC Card specification nor CF by cards based on revisions of the CF specification before Revision 3.0. Hosts shall ensure that all cards accessed through a common electrical interface are capable of operation at the desired, faster than 250 ns, I/O mode before configuring the interface for that I/O mode.

Advanced Timing modes are PCMCIA PC Card style I/O modes that are 100 ns or faster, PC Card Memory modes that are 100ns or faster, True IDE PIO Modes 5,6 and Multiword DMA Modes 3,4. These modes are permitted to be used only when a single card is present and the host and card are connected directly, without a cable exceeding 0.15m in length. Consequently, the host shall not configure a card into an Advanced Timing Mode if two cards are sharing I/O lines, as in Master/Slave operation, nor if it is constructed such that a cable exceeding 0.15 meters is required to connect the host to the card.

The load presented to the Host by cards supporting Ultra DMA is more controlled than that presented by other CompactFlash cards. Therefore, the use of a card that does not support Ultra DMA in a Master/Slave arrangement with a Ultra DMA card can affect the critical timing of the Ultra DMA transfers. The host shall not configure a card into Ultra DMA mode when a card not supporting Ultra DMA is also present on the same interface

When the use of two cards on an interface is otherwise permitted, the host may use any mode that is supported by both cards, but to achieve maximum performance it should use its highest performance mode that is also supported by both cards.

Metaformat Overview

The goal of the Metaformat is to describe the requirements and capabilities of the CompactFlash Storage Card as thoroughly as possible. This includes describing the power requirements, IO requirements, memory requirements, manufacturer information and details about the services provided.

Table: Sample Device Info Tuple Information for Extended Speeds

Note: The value “1” defined for D3 of the N+0 words indicates that no write-protect switch controls writing the ATA registers. The value “0” defined for D7 in the N+2 words indicates that there is not more than a single speed extension byte.

Transcend Information Inc.

49

V1.0

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Dimensions Placement FeaturesDescription Specification Actual Capacity PerformanceModel P/N Model P/N User LBA Cylinder Head SectorBlock Diagram TS16G~64GCF400 Pin Assignments and Pin Type PC Card Memory Mode PC Card I/O ModeTrue IDE Mode4 PC Card Memory Mode PC Card I/O Mode True IDE Mode4 Input Leakage Current Input CharacteristicsOutput Drive Type Output Drive Characteristics Output Drive CharacteristicsType Parameter Symbol Conditions Signal Name Dir Pin Description Signal Description400X CompactFlash Card StschgGND CselDir Signal NamePin Description Ready StopIntrq REG ResetDmack Iordy WaitDdmardy DstrobeCompactFlash Interface I/O at Electrical SpecificationParameter Symbol Input Power Input Characteristics for Udma modeOutput Drive Characteristics for Udma mode UnitsSignal Card10 Host10 Signal InterfacePull-up pin 45 BVD2 to avoid sensing their batteries as Low LowLow state 150 a high state per socketSeries termination required for Ultra DMA operation Ultra DMA Electrical RequirementsTable Typical Series Termination for Ultra DMA Ultra DMA Mode Cabling Requirement Symbol Attribute Memory Read Timing SpecificationIeee Symbol Min ns Max ns Speed VersionSpeed Version 250 ns Symbol Min ns Max ns Table Configuration Register Attribute Memory Write TimingCycle Time Mode Common Memory Read Timing SpecificationIeee 250 ns 120 ns 100 ns 80 ns MinCycle Time Mode 250 ns Symbol Common Memory Write Timing SpecificationSymbol 120 ns Min 100 ns MinCycle Time Mode 250 ns 120 ns 100 ns 80 ns Input Read Timing SpecificationMin Max Symbol Cycle Time Mode 255 ns 120 ns 100 ns 80 ns Output Write Timing SpecificationTsuHIOW TDVIWH ThHIOW TlWHDX TwHIOW TlWLIWH Mode True IDE PIO Mode Read/Write Timing SpecificationT6Z TS16G~64GCF400 True IDE Multiword DMA Mode Read/Write Timing Specification True IDE Ultra DMA Mode Read/Write Timing Specification Udma Signal Type PC Card MEM PC Card IO Mode True IDE ModeMode Udma Pin # NonTS16G~64GCF400 Name Name Comment Udma Name Mode Mode4Min Max 14.7Falling Edge Slew Rate for any signal Rising Edge Slew Rate for any signalMultiple Function CompactFlash Storage Cards Card ConfigurationREG Selected SpaceDMA Stop Dmardy Strobe Dmarq Dmack HioeHIO Inpack REGAttribute Memory Function Function ModeTable Attribute Memory Function DMA CMD REGConfiguration Option Register Base + 00h in Attribute Memory TS16G~64GCF400 Pin Replacement Register Base + 04h in Attribute Memory Socket and Copy Register Base + 06h in Attribute Memory Transfer Function Table Pcmcia Mode I/O FunctionDMA REG Hioe HiowDmardy Strobe Table PC Card I/O Mode Udma FunctionDmarq Dmack Stop Hioe Wait DMA A10 Inpack REG HiowTable Common Memory Function Common Memory Transfer FunctionCE2 CE1 D15-D8 D7-D0 True IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol Table Primary and Secondary I/O Decoding Primary and Secondary Address ConfigurationsTable Contiguous I/O Decoding Contiguous I/O Mapped AddressingMemory Mapped Addressing True IDE Mode AddressingData Register Address 1F0h170hOffset 0,8,9 CF-ATA RegistersSector Count Register Address 1F2h172h Offset Feature Register Address 1F1h171h Offset 1, 0Dh Write OnlySector Number LBA 7-0 Register Address 1F3h173h Offset Cylinder Low LBA 15-8 Register Address 1F4h174h OffsetTS16G~64GCF400 Device Control Register Address 3F6h376h Offset Eh Card Drive Address Register Address 3F7h377h Offset Fh Command Code CF-ATA Command SetDefinitions Execute Drive Diagnostic 90h Check Power Mode 98h or E5hBit Command Cyl High Cyl Low Sec Num Sec Cnt FeatureErase Sectors C0h Transcend Information IncFlush Cache E7h Format Track 50hWord Default Total Data Field Type Information Drive Cyl High Cyl Low Sec Num Sec Cnt FeatureIdentify Device Ech BytesDefault Total Data Field Type Information Word 1 Default Number of Cylinders Word 0 General ConfigurationCF Advanced True IDE Timing Mode Capability and Setting 164 162 0000h Key management schemes supported 163Word 6 Default Number of Sectors per Track Word 3 Default Number of HeadsWord 49 Capabilities Bit 13 Standby Timer PIO Data Transfer Cycle Timing ModeTotal Sectors Addressable in LBA Mode Multiple Sector SettingCurrent Capacity Multiword DMA transferWord 68 Minimum PIO transfer cycle time with Iordy Words 82-84 Features/command sets supportedWord 88 Ultra DMA Modes Supported and Selected Words 85-87 Features/command sets enabledWord 160 Power Requirement Description Word 91 Advanced power management level valueWord 89 Time required for Security erase unit completion Word 128 Security Status Bit 8 Security LevelMaximum PIO mode timing selected Value Current PIO timing mode selectedMaximum Multiword DMA timing mode supported Additional Requirements for CF Advanced Timing ModesMaximum Pcmcia IO timing mode Supported Value Current Multiword DMA timing mode selectedMaximum Memory timing mode Supported Value Maximum PC Card Memory Udma timing mode Supported Value Maximum PC Card I/O Udma timing mode SupportedValue PC Card Memory or I/O Udma timing mode Selected Idle Immediate 95h or E1h Idle 97h or E3hInitialize Drive Parameters 91h NOP 00hRead DMA C8h Read Long Sector 22h or 23h Read Buffer E4hTS16G~64GCF400 Request Sense 03h Seek 7Xh Set Features EFhFeature Supported TS16G~64GCF400 Translate Sector Information Standby Immediate 94h or E0h Translate Sector 87hWear Level F5h Write Buffer E8h Write DMA CAh TS16G~64GCF400 TS16G~64GCF400 Error Register Status Register Error PostingNOP BBKBBK UNC Idnf Abrt Amnf Drdy DWF DSC Corr ERR Smart Command Set Smart Feature Register Values Smart Command SetSmart Data Structure DescriptionSMI Transcend Product Capacity Ordering InformationCompactFlash Card

TS16G-64GCF400, 400X specifications

The Transcend Information TS16G-64GCF400, 400X is a high-performance CompactFlash card designed specifically to meet the demanding requirements of professionals in photography, video production, and data-intensive applications. With a capacity of 64GB and boasting an impressive transfer speed of up to 400X, the TS16G-64GCF400 is ideal for those seeking reliability and efficiency when recording high-resolution images and videos.

One of the standout features of this CompactFlash card is its exceptional read and write speeds. The card can achieve read speeds of up to 90 MB/s and write speeds that can reach up to 60 MB/s. These performance metrics make the TS16G-64GCF400 particularly suitable for burst shooting and continuous video recording, ensuring that every moment is captured accurately and without lag.

In terms of technology, the card utilizes advanced flash memory technology to enhance both speed and durability. Built with a robust construction, it is designed to withstand extreme conditions, making it resistant to shock, temperature fluctuations, and high humidity. This resilience is particularly important for users who often work in unpredictable environments or travel frequently.

The TS16G-64GCF400 is also equipped with the Ultra DMA mode, allowing for faster data transfer between the card and the camera or device it is used with. It supports both PIO and multi-word DMA modes, ensuring compatibility with a wide range of devices. Furthermore, it adheres to the CompactFlash Association's CF4.1 specifications, ensuring that users can rely on its performance across a variety of applications.

Another characteristic worth mentioning is the card's data security features. The Transcend TS16G-64GCF400 incorporates Error Correction Code (ECC) technology to detect and correct potential data corruption, ensuring that files remain intact over time. Additionally, it has built-in wear leveling technology to promote the distribution of write and erase cycles evenly across the memory cells, ultimately prolonging the lifespan of the card.

In conclusion, the Transcend Information TS16G-64GCF400, 400X CompactFlash card stands out in the competitive market of storage solutions. With its impressive speed, durability, and advanced features, it is an excellent choice for professional photographers and videographers who demand high performance and reliability in their storage devices. Whether capturing the next big moment or storing essential data, this card is sure to deliver the performance users need.
Top Page Image Contents