Intellinet Network Solutions INT-PSNC-UM-1106-06 Adjusting the Camera Lens, Adjusting the Focus

Page 25

5: Adjusting the Camera Lens

5.1 Adjusting the Focus

To get the finest image, adjust the lens focus according to your environment. Before adjusting, turn the set screw counterclockwise, then turn the lens in either direction till you get the most well-defined image edges while viewing the picture quality on your Web browser. When you finish adjusting the lens, turn the set screw clockwise to fix it in place.

Set Screw

Turn this part either clockwise or counterclockwise to adjust the lens focus.

Turn this part counterclockwise (with the lens facing you) to unscrew the lens for replacement.

NOTE: Do not force the lens beyond either the clockwise or counterclockwise limit. Also, a good level of focus is normally achievable throughout several planes within the camera’s focusing spectrum. Since optimum focusing is dependent upon the camera’s field of view, it is important to scan the focusing plane from the closest to furthest perspectives before attempting any fine- tuning.

5.2 Replacing the Lens

The Pro Series Network Camera is designed with a CS mount. The lens supplied with your product can be replaced with any standard C or CS lens, typically used within the surveillance industry. Follow the instructions below to replace the supplied lens with any C- or CS-type lens.

1.Unscrew the camera lens by turning the lens counterclockwise (see above).

2.For C lens only: Attach the new lens to a C-CS adapter.

3.Screw the new lens onto the camera. If applicable, adjust the iris according to the prevailing light conditions.

4.Focus the lens as instructed above.

5.Reload your Web browser and monitor the results from the product homepage.

NOTE: The Night Vision Infrared Camera is equipped with a special lens which cannot be replaced and must not be removed.

25

Image 25

Contents INT-PSNC-UM-1106-06 PRO SeriesTable of Contents Electromagnetic Compatibility EMC SafetyRadio Transmission Regulatory Information Video Standard and Product Classification Important NoticesProduct Overview Main Features and BenefitsAbout the Pro Series Network Cameras and Video Servers Physical Description Package ContentsMPEG4 CCD and Cmos Camera Front View Operating Status LED Power LEDRear View MPEG4 CCD IR Camera Reset Speaker Out Power Connector EthernetNetwork Video Server Video Input Video Output On Air Network LEDDome Glass Vandal Proof Dome Camera Front ViewTamper-proof screws Vari-focal lens 4-9 mmImage Capture LED Jpeg Cmos Camera 550710 Front/Top ViewNetwork Activity LED Network Connector Installation Summary and ExamplesRS232 Connector Power ConnectorPage Connecting the Camera to a PC Assigning an IP Address and Accessing the Camera’s HomepageSetting up the IP Address Using IP Installer Starting the Web Browser Accessing the Camera’s HomepageMS Internet Explorer MPEG4 Stream Mode Behind a Firewall Username and PasswordActiveX Installation for MS Explorer Users automatic Page Homepage Options MPEG4 Cameras Audio Video SizeSave Snapshot Install XviD Administrator MenuRecord Video LogoutExpansion Homepage Options Jpeg Cmos CameraFrame rate Show Only ImageAdjusting the Focus Adjusting the Camera LensReplacing the Lens Overview of the Administration Menu Administrator MenuQuality Rate ControlBit Rate Page Display Name/Location Stamp ResolutionDisplay Time/Date Stamp Vertical Flip and Horizontal FlipBrightness De-InterlaceContrast Hue Load Default ValuesSaturation Color KillerAuto Exposure MPEG4 Cmos CamerasMinimum Image Sensor Rate Auto White BalanceJpeg Cmos Camera Brightness ModeCompression Rate Image SizeBack Light Exposure ModeFurther Reduce Exposure Time Indoor / OutdoorPage Set IP address, Subnet Mask, Gateway Address Upgrade Port NumberSet Dhcp Send an IP address to EmailID, Password Use Smtp AuthenticationDdns Manual Update Rtsp Port NumberJpeg Cmos Camera Maximum Frame Rate PasswordAuthority PTZ Only Digital PTZ Camera modelsJpeg Cmos Camera Trigger Condition Event Trigger ConfigurationTop Middle Bottom Left Right MiddleMiddle Before event Image Capture OptionImage Capture option limitation Jpeg Cmos Camera Operation Mode and Output Stream Type System ConfigurationDirect Public Access to Image via Http Camera NameAudio On/Off Image File NameVideo On/Off LED On/OffPage Wireless Setup Wireless Configuration for wireless cameras onlyWireless Security Settings Page WPA & WPA2 personal Ad hoc Mode Infrastructure ModePower over Ethernet PoE Injector PoE Power over Ethernet SupportPoE Midspan PoE Web-Smart Switch PoE Office SwitchPower over Ethernet Injector Multi-Viewer Application for Windows InstallationConfiguration Adding a camera Camera InformationPage Etsp Client Setting up the camera in Etsp ClientGetting Started Click Add Define the location where Video should be saved Page Page Rtsp Playback in MPlayer for Windows Rtsp Video PlaybackPage Access to the camera via Https SSL Encryption / Access via HttpsPage MPEG4 Network Camera default values Remote Access to a Camera & Router SetupClick on NAT Virtual Server. Check x Enable Virtual Server Page Page Software Development Kit SDK Developer InformationWeb Integration MS Visual Studio C++, Visual BasicDirect public access to image via Http Direct Access to internal JpegMotion-JPEG Access IP Installer does not find the camera. Why? Appendix a Frequently Asked Questions FAQSender e-mail address max characters Use Smtp Authentication How do I activate the FTP upload function? Camera does not send any e-mails. Why?Short Why won’t the ActiveX control automatically download?Page Appendix B Accessing the camera via HyperTerminal Configure the parameters as shown below All MPEG4 models Symptoms Possible causes Remedial actions Appendix C TroubleshootingPINGing Your IP address Ping reply Interpretation and recommendationHub-to-hub cable Appendix D Utilizing IP Addresses on a Local Network Page Appendix E Updating Firmware Download New Firmware Install New FirmwareIdentify the Version of Firmware Function Description Appendix F The I/O Connector MPEG4 CamerasPIN Appendix G Dynamic Domain Name System Ddns How to Use the DynDNS Ddns ServerPage Page Page Ddns Registration for the Pro Series Network Camera Pressing the Reset Button Appendix H Reinstating the Factory Default SettingsUsing HyperTerminal Factory default settingsAppendix I Glossary of Terms Page Pro Series Network Camera Appendix J Product SpecificationsMPEG4, CCD, Day/Night, Ntsc Pro Series Wireless Network Camera Pro Series Wireless Network Camera MPEG4, CCD, Day/Night, IR Lens, PAL Pro Series Night Vision Network Camera100 Pro Series Wireless Night Vision Network Camera 102 MPEG4 + M-JPEG Dual Mode, 2.0 Megapixel CMOS, PAL/NTSC Pro Series Digital PTZ Network CameraPro Series Digital PTZ Wireless Network Camera MPEG4 + M-JPEG Dual Mode, Two-way Audio, PAL/NTSC Pro Series Network Video ServerJPEG, CMOS, PAL/NTSC 107 108