Arcam AVR500 / AVR600 / AV888 manual Speakers, Connecting speakers AVR500 & AVR600, Speaker cables

Page 25

speakers

Connecting speakers

– AVR500 & AVR600

The AVR500/AVR600 allows you to connect up to seven speakers and three active subwoofers in the main system. The output channels correspond to speakers installed in the front left, centre, front right, surround left, surround right, surround back left, surround back right and an active subwoofer.

The configuration and placement of your speakers is very important. All speakers, with the exception of the subwoofer, should be arranged around your normal viewing/listening position. The subwoofer should be placed in a position which gives an even frequency response in all listening positions. Incorrect placement leads to bass boom in some areas. Often the only

way to find a good position for your subwoofer is by experimentation. A good place to start experimenting

+Ð

L

C

R

SL

SR

SBL

SBR

To connect each of the speakers, unscrew the corresponding terminals on the back of the AVR500/ AVR600, insert the speaker wires through the hole in each post and screw the terminals back up. Make sure that the red (positive/+) terminal of the speaker is connected to the red (positive/+) terminal on the back panel, and the black (negative/–) terminal of the speaker is connected to the black (negative/–) terminal on the back panel.

Speaker cables

The speakers should be connected to the amplifier using good-quality, high-purity, low impedance copper cables. Cheap speaker cables should be avoided – they are a false economy and can significantly degrade the sound quality.

The cable runs to the speakers should be as short as practicable. Connections to the speaker terminals should always be finger tight, whether using bare wires or spade connectors.

English

is close to a wall but at least 1m away from any corners. You can also consult your subwoofer handbook for placement suggestions.

It is important that no stray strands of wire from these connections are allowed to

touch another cable or the product casing. Failure to ensure this can cause a short circuit and damage your AVR500/AVR600.

Do not over-tighten the loudspeaker terminals, or use a wrench, pliers, etc., as this could damage the terminals and this would not be covered under the product’s warranty.

SUBWOOFER OUTPUT

1

888 Connecting subwoofers

The AVR600 and the AV888 allow up to three active subwoofers to be connected to the SW1, SW2 or SW3 outputs. The AVR500 has two subwoofer connections.

See your subwoofer handbook for the correct setting up and connection for your particular subwoofer.

E-23

Page 24 Page 26
Image 25
Page 24 Page 26
Contents N d b o o k AVR surround amplifier / AV processor AVR500 / AVR600 / AV888Important safety instructions Safety GuidelinesSafety compliance Class II productInstructions de sécurité importantes Class II produitRespect des consignes de sécurité Page Professional Installation? ContentsDIY setup? WelcomeBefore you Begin… Standby power PowerPlacing the unit Interconnect cablesTrademark acknowledgements Making connections GeneralProduct differences and options Component/RGB Video CompositeAVR600 AV888 Zone 3 connectors Hdmi connectorsComponent/RGB video connectors Zone 2 connectorsDigital audio Phono Analogue audio ConnectorsTape inputs MCH inputInfra-red IR connectors Trigger connectorsSatellite receiver DVD playerCD player Use the Composite connection if HdmiConnecting an iPod using the Arcam rDock Component, S-Video and Composite connectors, see Video connectorsAVR500 Aerials, control and communicationAV, SAT, DVD Subwoofer outputs For more information on connecting speakers, seeFront panel Phones socket Trigger connectors Preferred video hook-up, in order of preference is VCR, Camcorder, Games Console etcConnecting an iPod using the Arcam rDock Aerial connectors AVR500/AVR600 only Radio ConnectorsSirius DAB optionConnecting an aerial Data connectors Network connectors USB connector Other ConnectorsRS232 serial connector RLead/rDockConnecting subwoofers Connecting speakers AVR500 & AVR600Speakers Speaker cablesSubwoofer CentreFront left and right Surround left and rightOperation Switching onOperating your AVR500 /AVR600 / AV888 Selecting a sourceUpdating firmware using a PC Using Zone 2Extended front panel menu Front panel Operation Inserting batteries into the remote control CR102 universal remote controllerUsing the remote control Useful information Device Mode / Source keysCode blink-back Controlling other devicesIPod commands AMP AMP Device ModeOK selects/play the highlighted file DVD DVD Device Mode TUN TUN Device ModeNetwork commands Highlighted menu on the screenAV AV Device Mode SAT SAT Device ModeMenus VCR VCR Device Mode PVR PVR Device ModeStarts Program mode CD CD Device ModeShift + rcycles through the repeat Options track, disc, etcSpeaker types Essential SetupSpeaker Distances Speaker LevelsAuto speaker setup Auto speaker SetupProblems Using a subwooferNavigating the setup menu Setup menusSelecting the video source VideoSelecting the audio source Treble Bass Input ConfigPlii Dimension Plii Centre Width Plii Panorama General SetupGeneral information and system controls Is usedSpkr Types Auto SetupSpkr Distance Spkr LevelsVideo Outputs Video InputsProgressive scan playback Important points to rememberMode Zone SettingsNetwork For Stereo sourcesEnglish Introduction Decoding ModesTwo-channel source modes Decoding modes Multichannel source modesVolume Leveller SettingsDolby Volume is a sophisticated new Calibration OffsetEnglish Saving and selecting Presets Tuning/Channel SelectionDeleting Presets Tuner OperationDefault unlock code is Sirius errorsAdd to your subscription OperationSelecting the playback source Network/usb OperationUSB playback Internet radio stationsAnalogue pre-amplifier outputs AVR600/AV888 only External AmplifiersEnglish XLR balanced line outputs AV888 only SW2, SW3Zone Multi-room Set upZone 3 AVR600/AV888 only Zone 2 and 3 control outputsZone English Multi-room connection guideCode Learning Customising CR102Creating Macros Volume punch-throughKey Mover Locking/Unlocking a specific Device Mode Mode MoverTo restore a moved Device Mode key to its original state Copy a key between Device ModesResetting the CR102 Mode key IR punch-throughProblem Check that When I turn on Volume is always too loudSwitched off Wired networkContinual improvement policy SpecificationsWorldwide Guarantee Product GuaranteeClaims under guarantee Problems?Device code Tables GEC GBCHCM HYDOKI NU-TECRBM RCAAVP YU-MA-TUGPX ADB STSNTL UPCAKI 3D LABAMW AtacomTVE TSMXMS AsciIdte HNEKPN SATSH222E Issue

AVR500 / AVR600 / AV888 specifications

The Arcam AVR500, AVR600, and AV888 are high-performance audio-video receivers that exemplify Arcam's commitment to delivering exceptional sound quality and versatility in home theater systems. Each model boasts a combination of advanced technologies, robust build quality, and a user-friendly interface, making them popular choices among audiophiles and home cinema enthusiasts.

The Arcam AVR500 is designed for those who appreciate high fidelity sound. It features a 7.1 channel amplifier delivering 100 watts per channel, allowing for immersive audio experiences. The AVR500 supports various audio formats, including Dolby TrueHD and DTS-HD Master Audio, ensuring that users can enjoy their favorite movies and music with rich, dynamic sound. The unit is equipped with extensive connectivity options, including multiple HDMI inputs and outputs, enabling seamless integration with other devices.

Moving up the line, the AVR600 enhances the AVR500's capabilities with additional power and features. It features a more powerful 120 watts per channel amplification and includes advanced room calibration technology known as Arc. This innovative feature optimizes audio playback by analyzing the room’s acoustics and adjusting the sound accordingly, helping to create a more immersive home theater experience. The AVR600 also supports 3D video pass-through and features HDMI 1.4 compatibility, making it future-proof for new video technologies.

At the pinnacle of this lineup, the Arcam AV888 takes a slightly different approach, focusing on becoming a premier preamp/processor that connects to external amplification. The AV888's superior processing ensures audiophiles experience the highest quality sound possible. With support for multi-channel PCM audio and a range of processing formats, users can experience the latest high-definition audio technologies. The unit houses advanced digital-to-analog converters for enhanced sound clarity and supports 4K video upscaling, making it an excellent choice for those invested in the latest visual standards.

All three models share a commitment to high-quality construction, ensuring durability and longevity. The user interface is intuitive, making navigation between functions seamless. This trio of receivers is compatible with various streaming services, allowing music to be enjoyed effortlessly from multiple sources.

In summary, the Arcam AVR500, AVR600, and AV888 provide exceptional sound quality, advanced features, and robust build quality, catering to an array of home entertainment needs. Whether for music or movies, these receivers promise rewarding and captivating listening experiences.
Top Page Image Contents