Arcam AVR500 / AVR600 / AV888 manual Multi-room Set up, Zone 3 AVR600/AV888 only

Page 56

multi-room

set up

The AVR500, AVR600 and AV888 allow independent routing and control of analogue audio, Composite and S-Video to a separate set of equipment, typically used for a second living space, e.g., bedroom or lounge. The AVR600 and AV888 also allow a copy of the Zone 2 analogue audio to be routed to and controlled in a third living space, Zone 3.

The connection guide on the facing page shows how the AVR600 or AV888 is normally connected in a multi- room installation.

Zone 2

Zone 2 receives only signals obtained by the AVR500, AVR600 or AV888 from the analogue audio, Composite and S-Video inputs. The analogue inputs are required because there is no analogue-to-digital, digital-to- analogue or DSP processing available for Zone 2 signals

– the unit only converts video formats for Zone 1.

For this reason, we recommend that in addition to any digital connections, the Composite and/or S-Video outputs from your source devices are connected to the AVR500, AVR600 or AV888.

Video outputs

The Z2 S-Video and/or Composite output connectors of the AVR500/AVR600/AV888 should be connected to the analogue video inputs (usually labelled S-Video In or Composite Video in) of the display device in Zone 2.

If you wish to make an HDMI connection to Zone 2, you must accept the limitations of the AVR500/AVR600/ AV888 video processing system.

HDMI OUT 1 and OUT 2 both carry the same signals (as there is only one video processing engine) and are

Audio outputs

The Z2 Out, R and L phono sockets should be connected to the analogue audio inputs (Usually labelled Analogue Audio in) of the Zone 2 display device, or to the inputs of an additional stereo power amplifier in Zone 2 (for example, the Arcam P38).

Zone 3 (AVR600/AV888 only)

A line-level signal from the stereo analogue audio is available for Zone 3. This is a copy of the Zone 2 audio signal, but has its own independent volume control.

Audio outputs

The Z3 Out, R and L phono sockets should be connected to the inputs of an additional stereo power amplifier in Zone 3 (for example, the Arcam P38).

Zone 2 and 3 control outputs

The AVR500, AVR600 and AV888 also allow remote control from remote zones.

Z2 IR and Z3 IR

This allows the AVR500/AVR600/AV888 to be controlled remotely from Zone 2 (or Zone 3) via Infra- red remote control. Connect a remote IR receiver in Zone 2 (or Zone 3) to allow control of the AVR500/ AVR600/AV888 from these listening/viewing areas.

For more information on remote IR receivers, see ‘Z1 IR’ on page 17.

TRIG Z2 and TRIG Z3

This allows the AVR500/AVR600/AV888 to remotely switch on devices in Zone 2 (or 3) when the appropriate Zone is selected. For example you could set your television in Zone 2 to switch on when ‘Zone 2’ is selected on AVR500/AVR600/AV888.

For more information on triggers, see ‘Trigger connectors’ on page 17. Please note that not all AV devices have this feature, nor are triggers essential for listening and viewing in a separate zone.

888

SIRIUS FM

primarily intended for use in Zone 1. Full HDMI video functionality in Zone 2 can only be achieved if Zone 1 is not being used at the same time.

If Zone 1 is being used at the same time as Zone 2, Zone 2 must follow the Zone 1 source selection if you wish to receive HDMI signals in Zone 2. Zone 2 must also be the same video resolution as Zone 1. If you wish

RS232rLead/rDock

AM

DAB

to watch a different source in Zone 2 than is currently showing over HDMI in Zone 1, Zone 2 will be forced to use the analogue video connections into and out of the AVR500/AVR600/AV888.

Due to the complications of using HDMI in Zone 2 we recommend the use of analogue video connections instead, particularly as it is not possible to apply audio lip sync to Zone 2 audio to compensate for video processing delays.

ETHERNET

Z1 IR

 

Z2 IR

TRIG Z1

 

USB

Z3 IR

TRIG Z2

IR OUT

TRIG Z3

E-54

Page 55 Page 57
Image 56
Page 55 Page 57
Contents AVR500 / AVR600 / AV888 N d b o o k AVR surround amplifier / AV processorSafety Guidelines Important safety instructionsSafety compliance Class II productRespect des consignes de sécurité Class II produitInstructions de sécurité importantes Page Contents Professional Installation?DIY setup? WelcomeBefore you Begin… Power Standby powerPlacing the unit Interconnect cablesTrademark acknowledgements General Making connectionsProduct differences and options Component/RGB Video CompositeAVR600 AV888 Hdmi connectors Zone 3 connectorsComponent/RGB video connectors Zone 2 connectorsConnectors Digital audio Phono Analogue audioTape inputs MCH inputTrigger connectors Infra-red IR connectorsDVD player Satellite receiverCD player Use the Composite connection if HdmiConnecting an iPod using the Arcam rDock Video connectors Component, S-Video and Composite connectors, seeAVR500 Aerials, control and communicationAV, SAT, DVD Front panel Phones socket For more information on connecting speakers, seeSubwoofer outputs Trigger connectors VCR, Camcorder, Games Console etc Preferred video hook-up, in order of preference isConnecting an iPod using the Arcam rDock Radio Connectors Aerial connectors AVR500/AVR600 onlySirius DAB optionConnecting an aerial Other Connectors Data connectors Network connectors USB connectorRS232 serial connector RLead/rDockConnecting speakers AVR500 & AVR600 Connecting subwoofersSpeakers Speaker cablesCentre SubwooferFront left and right Surround left and rightSwitching on OperationOperating your AVR500 /AVR600 / AV888 Selecting a sourceExtended front panel menu Using Zone 2Updating firmware using a PC Front panel Operation Using the remote control CR102 universal remote controllerInserting batteries into the remote control Device Mode / Source keys Useful informationControlling other devices Code blink-backOK selects/play the highlighted file AMP AMP Device ModeIPod commands TUN TUN Device Mode DVD DVD Device ModeNetwork commands Highlighted menu on the screenMenus SAT SAT Device ModeAV AV Device Mode PVR PVR Device Mode VCR VCR Device ModeCD CD Device Mode Starts Program modeShift + rcycles through the repeat Options track, disc, etcEssential Setup Speaker typesSpeaker Distances Speaker LevelsAuto speaker Setup Auto speaker setupProblems Using a subwooferSetup menus Navigating the setup menuSelecting the audio source VideoSelecting the video source Input Config Treble BassGeneral Setup Plii Dimension Plii Centre Width Plii PanoramaGeneral information and system controls Is usedAuto Setup Spkr TypesSpkr Distance Spkr LevelsVideo Inputs Video OutputsProgressive scan playback Important points to rememberZone Settings ModeNetwork For Stereo sourcesEnglish Two-channel source modes Decoding ModesIntroduction Multichannel source modes Decoding modesSettings Volume LevellerDolby Volume is a sophisticated new Calibration OffsetEnglish Tuning/Channel Selection Saving and selecting PresetsDeleting Presets Tuner OperationSirius errors Default unlock code isAdd to your subscription OperationNetwork/usb Operation Selecting the playback sourceUSB playback Internet radio stationsExternal Amplifiers Analogue pre-amplifier outputs AVR600/AV888 onlyEnglish XLR balanced line outputs AV888 only SW2, SW3Multi-room Set up ZoneZone 3 AVR600/AV888 only Zone 2 and 3 control outputsMulti-room connection guide Zone EnglishCustomising CR102 Code LearningKey Mover Volume punch-throughCreating Macros Mode Mover Locking/Unlocking a specific Device ModeTo restore a moved Device Mode key to its original state Copy a key between Device ModesMode key IR punch-through Resetting the CR102Problem Check that Volume is always too loud When I turn onSwitched off Wired networkSpecifications Continual improvement policyProduct Guarantee Worldwide GuaranteeClaims under guarantee Problems?Device code Tables GBC GECHCM HYDNU-TEC OKIRBM RCAGPX YU-MA-TUAVP STS ADBNTL UPC3D LAB AKIAMW AtacomTSM TVEXMS AsciHNE IdteKPN SATSH222E Issue

AVR500 / AVR600 / AV888 specifications

The Arcam AVR500, AVR600, and AV888 are high-performance audio-video receivers that exemplify Arcam's commitment to delivering exceptional sound quality and versatility in home theater systems. Each model boasts a combination of advanced technologies, robust build quality, and a user-friendly interface, making them popular choices among audiophiles and home cinema enthusiasts.

The Arcam AVR500 is designed for those who appreciate high fidelity sound. It features a 7.1 channel amplifier delivering 100 watts per channel, allowing for immersive audio experiences. The AVR500 supports various audio formats, including Dolby TrueHD and DTS-HD Master Audio, ensuring that users can enjoy their favorite movies and music with rich, dynamic sound. The unit is equipped with extensive connectivity options, including multiple HDMI inputs and outputs, enabling seamless integration with other devices.

Moving up the line, the AVR600 enhances the AVR500's capabilities with additional power and features. It features a more powerful 120 watts per channel amplification and includes advanced room calibration technology known as Arc. This innovative feature optimizes audio playback by analyzing the room’s acoustics and adjusting the sound accordingly, helping to create a more immersive home theater experience. The AVR600 also supports 3D video pass-through and features HDMI 1.4 compatibility, making it future-proof for new video technologies.

At the pinnacle of this lineup, the Arcam AV888 takes a slightly different approach, focusing on becoming a premier preamp/processor that connects to external amplification. The AV888's superior processing ensures audiophiles experience the highest quality sound possible. With support for multi-channel PCM audio and a range of processing formats, users can experience the latest high-definition audio technologies. The unit houses advanced digital-to-analog converters for enhanced sound clarity and supports 4K video upscaling, making it an excellent choice for those invested in the latest visual standards.

All three models share a commitment to high-quality construction, ensuring durability and longevity. The user interface is intuitive, making navigation between functions seamless. This trio of receivers is compatible with various streaming services, allowing music to be enjoyed effortlessly from multiple sources.

In summary, the Arcam AVR500, AVR600, and AV888 provide exceptional sound quality, advanced features, and robust build quality, catering to an array of home entertainment needs. Whether for music or movies, these receivers promise rewarding and captivating listening experiences.
Top Page Image Contents