Arcam AVR500 / AVR600 / AV888 manual Specifications, Continual improvement policy

Page 64

specifications

Continuous power output (20Hz—20kHz at 0.05% THD), per channel (AVR600)

2 channels driven

150W

All channels driven

120W

THD at full rated power

<0.2%

Residual noise & hum

<0.25mV unweighted 20Hz – 22kHz

Continuous power output (20Hz—20kHz at 0.05% THD), per channel

(AVR500)

 

2 channels driven

120w

All channels driven

100w

THD at full rated power

<0.2%

Residual noise & hum

<0.25mV unweighted 20Hz – 22kHz

Inputs

 

Phono input:

 

Input sensitivity at 1kHz

5mV

Input impedance

47kΩ

Signal/noise ratio (CCIR, 65W)

88dB

Overload margin

31dB

Line inputs:

 

Nominal sensitivity

500mV–4V (user adjustable)

Input impedance

47kΩ

Signal/noise ratio (CCIR, 65W)

100dB

Preamplifier outputs

 

Max output level

6V RMS

Output impedance

<50Ω

THD+N (20Hz—20kHz)

-100dB

Video inputs

 

Component video signal/noise

85dB

Composite video signal/noise

70dB

Headphone output

 

Maximum output level into 600Ω

4V p-p

Output impedance

<5Ω

General

Mains voltage

110–120V or 220–240V

Power consumption (maximum)

 

 

AVR500/AVR600

1.5kVA (Thermal dissipation approx.

 

 

5200 BTU/hour)

 

AV888

120VA (Thermal dissipation approx.

 

 

410BTU/hour)

Power consumption (idle, typical)

120VA (Thermal dissipation approx.

 

 

410 BTU/hour)

Power consumption (standby)

3VA

Dimensions W x D x H (including feet)

 

 

AVR500, AVR600

433mm x 472mm x 180mm

 

AV888

433mm x 472mm x 183mm

Weight (net)

 

 

AVR500

23.0kg

 

AVR600

25.0kg

 

AV888

12.0kg

Weight (packed)

 

 

AVR500

28.0kg

 

AVR600

30.0kg

 

AV888

17.0kg

Supplied accessories

Mains lead

 

 

CR102 remote control

 

 

4 x AAA batteries

 

 

Manual

 

 

HDMI lead support bar

 

 

DAB aerial (if DAB module fitted)

 

 

FM aerial (if AM/FM fitted)

 

 

AM loop aerial (if AM/FM fitted)

 

 

Calibration microphone

E&OE

NOTE: All specification values are typical unless otherwise stated.

Continual improvement policy

Arcam has a policy of continual improvement for its products. This means that designs and specifications are subject to change without notice.

E-62

Page 63 Page 65
Image 64
Page 63 Page 65
Contents AVR500 / AVR600 / AV888 N d b o o k AVR surround amplifier / AV processorSafety Guidelines Important safety instructionsSafety compliance Class II productInstructions de sécurité importantes Class II produitRespect des consignes de sécurité Page Contents Professional Installation?DIY setup? WelcomeBefore you Begin… Power Standby powerPlacing the unit Interconnect cablesTrademark acknowledgements General Making connectionsProduct differences and options Component/RGB Video CompositeAVR600 AV888 Hdmi connectors Zone 3 connectorsComponent/RGB video connectors Zone 2 connectorsConnectors Digital audio Phono Analogue audioTape inputs MCH inputTrigger connectors Infra-red IR connectorsDVD player Satellite receiverCD player Use the Composite connection if HdmiConnecting an iPod using the Arcam rDock Video connectors Component, S-Video and Composite connectors, seeAVR500 Aerials, control and communicationAV, SAT, DVD Subwoofer outputs For more information on connecting speakers, seeFront panel Phones socket Trigger connectors VCR, Camcorder, Games Console etc Preferred video hook-up, in order of preference isConnecting an iPod using the Arcam rDock Radio Connectors Aerial connectors AVR500/AVR600 onlySirius DAB optionConnecting an aerial Other Connectors Data connectors Network connectors USB connectorRS232 serial connector RLead/rDockConnecting speakers AVR500 & AVR600 Connecting subwoofersSpeakers Speaker cablesCentre SubwooferFront left and right Surround left and rightSwitching on OperationOperating your AVR500 /AVR600 / AV888 Selecting a sourceUpdating firmware using a PC Using Zone 2Extended front panel menu Front panel Operation Inserting batteries into the remote control CR102 universal remote controllerUsing the remote control Device Mode / Source keys Useful informationControlling other devices Code blink-backIPod commands AMP AMP Device ModeOK selects/play the highlighted file TUN TUN Device Mode DVD DVD Device ModeNetwork commands Highlighted menu on the screenAV AV Device Mode SAT SAT Device ModeMenus PVR PVR Device Mode VCR VCR Device ModeCD CD Device Mode Starts Program modeShift + rcycles through the repeat Options track, disc, etcEssential Setup Speaker typesSpeaker Distances Speaker LevelsAuto speaker Setup Auto speaker setupProblems Using a subwooferSetup menus Navigating the setup menuSelecting the video source VideoSelecting the audio source Input Config Treble BassGeneral Setup Plii Dimension Plii Centre Width Plii PanoramaGeneral information and system controls Is usedAuto Setup Spkr TypesSpkr Distance Spkr LevelsVideo Inputs Video OutputsProgressive scan playback Important points to rememberZone Settings ModeNetwork For Stereo sourcesEnglish Introduction Decoding ModesTwo-channel source modes Multichannel source modes Decoding modesSettings Volume LevellerDolby Volume is a sophisticated new Calibration OffsetEnglish Tuning/Channel Selection Saving and selecting PresetsDeleting Presets Tuner OperationSirius errors Default unlock code isAdd to your subscription OperationNetwork/usb Operation Selecting the playback sourceUSB playback Internet radio stationsExternal Amplifiers Analogue pre-amplifier outputs AVR600/AV888 onlyEnglish XLR balanced line outputs AV888 only SW2, SW3Multi-room Set up ZoneZone 3 AVR600/AV888 only Zone 2 and 3 control outputsMulti-room connection guide Zone EnglishCustomising CR102 Code LearningCreating Macros Volume punch-throughKey Mover Mode Mover Locking/Unlocking a specific Device ModeTo restore a moved Device Mode key to its original state Copy a key between Device ModesMode key IR punch-through Resetting the CR102Problem Check that Volume is always too loud When I turn onSwitched off Wired networkSpecifications Continual improvement policyProduct Guarantee Worldwide GuaranteeClaims under guarantee Problems?Device code Tables GBC GECHCM HYDNU-TEC OKIRBM RCAAVP YU-MA-TUGPX STS ADBNTL UPC3D LAB AKIAMW AtacomTSM TVEXMS AsciHNE IdteKPN SATSH222E Issue

AVR500 / AVR600 / AV888 specifications

The Arcam AVR500, AVR600, and AV888 are high-performance audio-video receivers that exemplify Arcam's commitment to delivering exceptional sound quality and versatility in home theater systems. Each model boasts a combination of advanced technologies, robust build quality, and a user-friendly interface, making them popular choices among audiophiles and home cinema enthusiasts.

The Arcam AVR500 is designed for those who appreciate high fidelity sound. It features a 7.1 channel amplifier delivering 100 watts per channel, allowing for immersive audio experiences. The AVR500 supports various audio formats, including Dolby TrueHD and DTS-HD Master Audio, ensuring that users can enjoy their favorite movies and music with rich, dynamic sound. The unit is equipped with extensive connectivity options, including multiple HDMI inputs and outputs, enabling seamless integration with other devices.

Moving up the line, the AVR600 enhances the AVR500's capabilities with additional power and features. It features a more powerful 120 watts per channel amplification and includes advanced room calibration technology known as Arc. This innovative feature optimizes audio playback by analyzing the room’s acoustics and adjusting the sound accordingly, helping to create a more immersive home theater experience. The AVR600 also supports 3D video pass-through and features HDMI 1.4 compatibility, making it future-proof for new video technologies.

At the pinnacle of this lineup, the Arcam AV888 takes a slightly different approach, focusing on becoming a premier preamp/processor that connects to external amplification. The AV888's superior processing ensures audiophiles experience the highest quality sound possible. With support for multi-channel PCM audio and a range of processing formats, users can experience the latest high-definition audio technologies. The unit houses advanced digital-to-analog converters for enhanced sound clarity and supports 4K video upscaling, making it an excellent choice for those invested in the latest visual standards.

All three models share a commitment to high-quality construction, ensuring durability and longevity. The user interface is intuitive, making navigation between functions seamless. This trio of receivers is compatible with various streaming services, allowing music to be enjoyed effortlessly from multiple sources.

In summary, the Arcam AVR500, AVR600, and AV888 provide exceptional sound quality, advanced features, and robust build quality, catering to an array of home entertainment needs. Whether for music or movies, these receivers promise rewarding and captivating listening experiences.
Top Page Image Contents