Arcam AVR500 / AVR600 / AV888 manual Using Zone 2, Extended front panel menu

Page 28

Headphones

To use headphones with the unit, plug the headphones into the Phones socket in the centre of the front panel.

When headphones are plugged into the front panel phones socket, the outputs for Zone 1 are muted and the audio will be down-mixed to two channels (2.0). The two-channel down-mix is required so that the centre channel and surround information can be heard via the headphones.

Using Zone 2 and 3

Zone 2 provides the option for the occupants of the master bedroom, conservatory, kitchen, etc. to view or listen to a different source at a different volume level from the main zone (Zone 1).

Zone 3 (AVR600/AV888 only) provides for a third living space to have a copy of the audio signal in Zone 2 at a different volume level.

Extended front panel menu

Pressing the menu key and holding it for longer than four seconds will bring up the Extended Menu, allowing you to perform the following:

Restore to factory defaults

This option allows you to restore all settings on your AVR500/AVR600/AV888 to the defaults that it left the factory with. Note that this also erases any secure backups stored on the unit.

Restore secure backup

Store secure backup

This option allows you to restore from and store to a PIN-protected copy of your settings. The default PIN is 1234.

Change remote code

The default RC5 system code the unit responds to is

16.If required, for example due to another device in your system also using this RC5 system code, it can be changed to 19.

Software versions

Information on the software version of the unit can be found here.

Updating firmware using a PC

Using a PC application (available on request from Arcam), you can update the firmware in your AVR500/ AVR600/AV888 using the back panel RS232 port connected to your PC.

E-26

Page 27 Page 29
Image 28
Page 27 Page 29
Contents AVR500 / AVR600 / AV888 N d b o o k AVR surround amplifier / AV processorSafety Guidelines Important safety instructionsSafety compliance Class II productInstructions de sécurité importantes Class II produitRespect des consignes de sécurité Page Contents Professional Installation?DIY setup? WelcomeBefore you Begin… Power Standby powerPlacing the unit Interconnect cablesTrademark acknowledgements General Making connectionsProduct differences and options Component/RGB Video CompositeAVR600 AV888 Hdmi connectors Zone 3 connectorsComponent/RGB video connectors Zone 2 connectorsConnectors Digital audio Phono Analogue audioTape inputs MCH inputTrigger connectors Infra-red IR connectorsDVD player Satellite receiverCD player Use the Composite connection if HdmiConnecting an iPod using the Arcam rDock Video connectors Component, S-Video and Composite connectors, seeAVR500 Aerials, control and communicationAV, SAT, DVD Subwoofer outputs For more information on connecting speakers, seeFront panel Phones socket Trigger connectors VCR, Camcorder, Games Console etc Preferred video hook-up, in order of preference isConnecting an iPod using the Arcam rDock Radio Connectors Aerial connectors AVR500/AVR600 onlySirius DAB optionConnecting an aerial Other Connectors Data connectors Network connectors USB connectorRS232 serial connector RLead/rDockConnecting speakers AVR500 & AVR600 Connecting subwoofersSpeakers Speaker cablesCentre SubwooferFront left and right Surround left and rightSwitching on OperationOperating your AVR500 /AVR600 / AV888 Selecting a sourceUpdating firmware using a PC Using Zone 2Extended front panel menu Front panel Operation Inserting batteries into the remote control CR102 universal remote controllerUsing the remote control Device Mode / Source keys Useful informationControlling other devices Code blink-backIPod commands AMP AMP Device ModeOK selects/play the highlighted file TUN TUN Device Mode DVD DVD Device ModeNetwork commands Highlighted menu on the screenAV AV Device Mode SAT SAT Device ModeMenus PVR PVR Device Mode VCR VCR Device ModeCD CD Device Mode Starts Program modeShift + rcycles through the repeat Options track, disc, etcEssential Setup Speaker typesSpeaker Distances Speaker LevelsAuto speaker Setup Auto speaker setupProblems Using a subwooferSetup menus Navigating the setup menuSelecting the video source VideoSelecting the audio source Input Config Treble BassGeneral Setup Plii Dimension Plii Centre Width Plii PanoramaGeneral information and system controls Is usedAuto Setup Spkr TypesSpkr Distance Spkr LevelsVideo Inputs Video OutputsProgressive scan playback Important points to rememberZone Settings ModeNetwork For Stereo sourcesEnglish Introduction Decoding ModesTwo-channel source modes Multichannel source modes Decoding modesSettings Volume LevellerDolby Volume is a sophisticated new Calibration OffsetEnglish Tuning/Channel Selection Saving and selecting PresetsDeleting Presets Tuner OperationSirius errors Default unlock code isAdd to your subscription OperationNetwork/usb Operation Selecting the playback sourceUSB playback Internet radio stationsExternal Amplifiers Analogue pre-amplifier outputs AVR600/AV888 onlyEnglish XLR balanced line outputs AV888 only SW2, SW3Multi-room Set up ZoneZone 3 AVR600/AV888 only Zone 2 and 3 control outputsMulti-room connection guide Zone EnglishCustomising CR102 Code LearningCreating Macros Volume punch-throughKey Mover Mode Mover Locking/Unlocking a specific Device ModeTo restore a moved Device Mode key to its original state Copy a key between Device ModesMode key IR punch-through Resetting the CR102Problem Check that Volume is always too loud When I turn onSwitched off Wired networkSpecifications Continual improvement policyProduct Guarantee Worldwide GuaranteeClaims under guarantee Problems?Device code Tables GBC GECHCM HYDNU-TEC OKIRBM RCAAVP YU-MA-TUGPX STS ADBNTL UPC3D LAB AKIAMW AtacomTSM TVEXMS AsciHNE IdteKPN SATSH222E Issue

AVR500 / AVR600 / AV888 specifications

The Arcam AVR500, AVR600, and AV888 are high-performance audio-video receivers that exemplify Arcam's commitment to delivering exceptional sound quality and versatility in home theater systems. Each model boasts a combination of advanced technologies, robust build quality, and a user-friendly interface, making them popular choices among audiophiles and home cinema enthusiasts.

The Arcam AVR500 is designed for those who appreciate high fidelity sound. It features a 7.1 channel amplifier delivering 100 watts per channel, allowing for immersive audio experiences. The AVR500 supports various audio formats, including Dolby TrueHD and DTS-HD Master Audio, ensuring that users can enjoy their favorite movies and music with rich, dynamic sound. The unit is equipped with extensive connectivity options, including multiple HDMI inputs and outputs, enabling seamless integration with other devices.

Moving up the line, the AVR600 enhances the AVR500's capabilities with additional power and features. It features a more powerful 120 watts per channel amplification and includes advanced room calibration technology known as Arc. This innovative feature optimizes audio playback by analyzing the room’s acoustics and adjusting the sound accordingly, helping to create a more immersive home theater experience. The AVR600 also supports 3D video pass-through and features HDMI 1.4 compatibility, making it future-proof for new video technologies.

At the pinnacle of this lineup, the Arcam AV888 takes a slightly different approach, focusing on becoming a premier preamp/processor that connects to external amplification. The AV888's superior processing ensures audiophiles experience the highest quality sound possible. With support for multi-channel PCM audio and a range of processing formats, users can experience the latest high-definition audio technologies. The unit houses advanced digital-to-analog converters for enhanced sound clarity and supports 4K video upscaling, making it an excellent choice for those invested in the latest visual standards.

All three models share a commitment to high-quality construction, ensuring durability and longevity. The user interface is intuitive, making navigation between functions seamless. This trio of receivers is compatible with various streaming services, allowing music to be enjoyed effortlessly from multiple sources.

In summary, the Arcam AVR500, AVR600, and AV888 provide exceptional sound quality, advanced features, and robust build quality, catering to an array of home entertainment needs. Whether for music or movies, these receivers promise rewarding and captivating listening experiences.
Top Page Image Contents