Arcam AVR500 / AVR600 / AV888 Speakers, Or DTS decoding modes, DVD, the AVR600 selects, Source

Page 63

Problem

Check that...

Sound only comes from some

< you have an appropriate surround source selected and playing.

of the speakers

< the DVD disc is encoded in the appropriate format, and the correct format

 

has been selected in the disc start menu of the DVD player (if applicable).

 

< the DVD player has been set to output ‘bitstream’ audio on the digital

 

output.

 

< the display window indicates that the disc you are playing is a multichannel

 

recording (you may need to press the INFO key several times until you get to

 

the ‘incoming format’ display).

 

< all the speakers are correctly connected to the speaker terminals and are

 

secure.

 

< you have not selected ‘Stereo’ as the decoding mode.

 

< your speaker balance is correct.

 

< you have configured the unit to include all the speakers in your system.

Unable to select Dolby Digital

The AVR500/AVR600/AV888 can only apply Dolby Digital and DTS decoding

or DTS decoding modes

to sources which have been encoded in the same format.

 

Check that:

 

< digital source is selected and connected.

 

< the source is playing appropriately encoded material.

 

< the DVD disc is encoded in the appropriate format and that the correct

 

format has been selected in the disc start menu of the DVD player (if

 

applicable).

 

< the DVD player has been set to output ‘bitstream’ audio on the digital output

 

(not PCM).

When playing a Dolby Digital

< you have a digital connection from your DVD player.

DVD, the AVR600 selects

< sometimes Dolby Digital DVD discs contain material at either the beginning

Dolby Pro Logic

or the end of the main movie that is not in full 5.1 format, but in two-

 

channel or Pro Logic decoding.

Hum on the analogue input

< all cables are making a good connection. If necessary withdraw the cable

 

from the connector and plug it fully in again (turn the power off before

 

doing this).

 

< the connections inside the source cable connector are not broken or badly

 

soldered.

 

< if the hum originates only when one particular source component is

 

connected, that an aerial cable, or dish connection to this source is ground

 

isolated. Contact your installation contractor.

There is radio or television

< where the interference is coming from. Switch off each source component in

reception interference

turn, then any other equipment. Most electronic equipment does generate

 

low levels of interference.

 

< try re-arranging cabling from the nuisance source away from other cabling.

 

< ensure that the cabling used is high quality, specified for its purpose, and is

 

properly screened.

 

< if the problem persists, contact your dealer.

Problem

Check that...

The source switching changes

< there are no static or impulse interference problems caused by nearby power

randomly or freezes on one

equipment switching, e.g., heating or air conditioning control. Switch the

source

unit off, wait ten seconds, then switch it on again to clear an operating

 

problem. Contact your installer if the problem returns or persists.

 

< there is no direct sunlight shining on the infra-red detector behind the front

 

panel display.

Volume is always too loud

< the ‘max on volume’ setting is not set too high.

when I turn on

 

When Zone 2 or 3 is put into

< the ‘zone standby‘ setting in the setup menu is set to LOCAL.

standby, the main zone is also

 

switched off

 

When a USB memory device is

< a USB memory device is connected that conforms to the mass storage class.

connected, ‘USB’ is not shown

< a USB hub is not being used.

in the network client’s list of

 

folders

 

If files on a USB memory

< the USB device is formatted in FAT16 or FAT32.

device cannot be played:

< the USB device does not have multiple partitions.

 

 

< the files are in a compatible format.

If files on a computer cannot

< the files are in a compatible format.

be played

< the computer is connected via a network and not USB – the AVR500/

 

AVR600/AV888 USB port cannot be used for a direct connection to a

 

computer

If you cannot connect to a

< the Ethernet cable you are using is correctly connected between the

wired network

AVR500/AVR600/AV888 and the network hardware.

 

< the network is set up for fixed IP addressing and you have the AVR500/

 

AVR600/AV888 set to use DHCP.

 

< the network is set up for DHCP and you have the AVR500/AVR600/AV888

 

set to use fixed IP addressing.

If you cannot connect to a

< the station is still broadcasting or is not congested – try again later.

favourite internet radio station

 

If the internet radio station

< the radio station does not have a low bit rate (use the INFO key to find this or

sound quality is poor or

look on the OSD).

broken

< the network is not slow or congested.

 

English

E-61

Page 62 Page 64
Image 63
Page 62 Page 64
Contents N d b o o k AVR surround amplifier / AV processor AVR500 / AVR600 / AV888Class II product Safety GuidelinesImportant safety instructions Safety complianceClass II produit Instructions de sécurité importantesRespect des consignes de sécurité Page Welcome ContentsProfessional Installation? DIY setup?Before you Begin… Interconnect cables PowerStandby power Placing the unitTrademark acknowledgements Component/RGB Video Composite GeneralMaking connections Product differences and optionsAVR600 AV888 Zone 2 connectors Hdmi connectorsZone 3 connectors Component/RGB video connectorsMCH input ConnectorsDigital audio Phono Analogue audio Tape inputsInfra-red IR connectors Trigger connectorsUse the Composite connection if Hdmi DVD playerSatellite receiver CD playerConnecting an iPod using the Arcam rDock Aerials, control and communication Video connectorsComponent, S-Video and Composite connectors, see AVR500AV, SAT, DVD For more information on connecting speakers, see Subwoofer outputsFront panel Phones socket Trigger connectors Preferred video hook-up, in order of preference is VCR, Camcorder, Games Console etcConnecting an iPod using the Arcam rDock DAB option Radio ConnectorsAerial connectors AVR500/AVR600 only SiriusConnecting an aerial RLead/rDock Other ConnectorsData connectors Network connectors USB connector RS232 serial connectorSpeaker cables Connecting speakers AVR500 & AVR600Connecting subwoofers SpeakersSurround left and right CentreSubwoofer Front left and rightSelecting a source Switching onOperation Operating your AVR500 /AVR600 / AV888Using Zone 2 Updating firmware using a PCExtended front panel menu Front panel Operation CR102 universal remote controller Inserting batteries into the remote controlUsing the remote control Useful information Device Mode / Source keysCode blink-back Controlling other devicesAMP AMP Device Mode IPod commandsOK selects/play the highlighted file Highlighted menu on the screen TUN TUN Device ModeDVD DVD Device Mode Network commandsSAT SAT Device Mode AV AV Device ModeMenus VCR VCR Device Mode PVR PVR Device ModeOptions track, disc, etc CD CD Device ModeStarts Program mode Shift + rcycles through the repeatSpeaker Levels Essential SetupSpeaker types Speaker DistancesUsing a subwoofer Auto speaker SetupAuto speaker setup ProblemsNavigating the setup menu Setup menusVideo Selecting the video sourceSelecting the audio source Treble Bass Input ConfigIs used General SetupPlii Dimension Plii Centre Width Plii Panorama General information and system controlsSpkr Levels Auto SetupSpkr Types Spkr DistanceImportant points to remember Video InputsVideo Outputs Progressive scan playbackFor Stereo sources Zone SettingsMode NetworkEnglish Decoding Modes IntroductionTwo-channel source modes Decoding modes Multichannel source modesCalibration Offset SettingsVolume Leveller Dolby Volume is a sophisticated newEnglish Tuner Operation Tuning/Channel SelectionSaving and selecting Presets Deleting PresetsOperation Sirius errorsDefault unlock code is Add to your subscriptionInternet radio stations Network/usb OperationSelecting the playback source USB playbackSW2, SW3 External AmplifiersAnalogue pre-amplifier outputs AVR600/AV888 only English XLR balanced line outputs AV888 onlyZone 2 and 3 control outputs Multi-room Set upZone Zone 3 AVR600/AV888 onlyZone English Multi-room connection guideCode Learning Customising CR102Volume punch-through Creating MacrosKey Mover Copy a key between Device Modes Mode MoverLocking/Unlocking a specific Device Mode To restore a moved Device Mode key to its original stateResetting the CR102 Mode key IR punch-throughProblem Check that Wired network Volume is always too loudWhen I turn on Switched offContinual improvement policy SpecificationsProblems? Product GuaranteeWorldwide Guarantee Claims under guaranteeDevice code Tables HYD GBCGEC HCMRCA NU-TECOKI RBMYU-MA-TU AVPGPX UPC STSADB NTLAtacom 3D LABAKI AMWAsci TSMTVE XMSSAT HNEIdte KPNSH222E Issue

AVR500 / AVR600 / AV888 specifications

The Arcam AVR500, AVR600, and AV888 are high-performance audio-video receivers that exemplify Arcam's commitment to delivering exceptional sound quality and versatility in home theater systems. Each model boasts a combination of advanced technologies, robust build quality, and a user-friendly interface, making them popular choices among audiophiles and home cinema enthusiasts.

The Arcam AVR500 is designed for those who appreciate high fidelity sound. It features a 7.1 channel amplifier delivering 100 watts per channel, allowing for immersive audio experiences. The AVR500 supports various audio formats, including Dolby TrueHD and DTS-HD Master Audio, ensuring that users can enjoy their favorite movies and music with rich, dynamic sound. The unit is equipped with extensive connectivity options, including multiple HDMI inputs and outputs, enabling seamless integration with other devices.

Moving up the line, the AVR600 enhances the AVR500's capabilities with additional power and features. It features a more powerful 120 watts per channel amplification and includes advanced room calibration technology known as Arc. This innovative feature optimizes audio playback by analyzing the room’s acoustics and adjusting the sound accordingly, helping to create a more immersive home theater experience. The AVR600 also supports 3D video pass-through and features HDMI 1.4 compatibility, making it future-proof for new video technologies.

At the pinnacle of this lineup, the Arcam AV888 takes a slightly different approach, focusing on becoming a premier preamp/processor that connects to external amplification. The AV888's superior processing ensures audiophiles experience the highest quality sound possible. With support for multi-channel PCM audio and a range of processing formats, users can experience the latest high-definition audio technologies. The unit houses advanced digital-to-analog converters for enhanced sound clarity and supports 4K video upscaling, making it an excellent choice for those invested in the latest visual standards.

All three models share a commitment to high-quality construction, ensuring durability and longevity. The user interface is intuitive, making navigation between functions seamless. This trio of receivers is compatible with various streaming services, allowing music to be enjoyed effortlessly from multiple sources.

In summary, the Arcam AVR500, AVR600, and AV888 provide exceptional sound quality, advanced features, and robust build quality, catering to an array of home entertainment needs. Whether for music or movies, these receivers promise rewarding and captivating listening experiences.
Top Page Image Contents