Arcam AVR500 / AVR600 / AV888 manual Mode, Zone Settings, Network, For Stereo sources

Page 46

Out 1 & 2 Resolution – This setting controls the output resolution when both HDMI outputs are used simultaneously. This setting is only valid if Output Switching is set to Output 1 & 2.

<The dropdown list shows all the resolutions that the video processor can output. Resolutions that are not supported by the connected display devices are greyed out and cannot be selected.

<Best: sets the HDMI output to be the highest common resolution that is supported by both display devices.

Out 1 & 2 Frame Rate – This setting controls the output frame rate when both HDMI outputs are used simultaneously. This setting is only valid if Output Switching is set to Output 1 & 2.

<The dropdown list shows all the frame rates that the video processor can output. Frame rates that are not supported by the connected display devices at the above resolution are greyed out and cannot be selected.

<Auto: sets the HDMI output to be the highest preferred common frame rate that is supported by both display devices for the above resolution.

<Follow Input forces the out 1 & 2 frame rate to the same as the input frame rate, regardless of the reported capabilities of the display device.

Lipsync 1 & 2 – (Information only) Displays how much lip sync is automatically applied to HDMI outputs Out 1 and Out 2 simultaneously to compensate for video processing delays in the attached display devices. Not all display devices support this function.

Mode

Lists the decode and downmix options you wish to include when cycling through the options on the MODE button. Settings are Yes or No. The list is divided into two sections depending on the source audio type. See section ‘Multichannel source modes’ on page 47 for more information on each processing a decoding mode.

These settings are applied to all audio inputs and are stored in memory and recalled each time the unit is powered up.

For Stereo sources:

Dolby ProLogic –

Dolby PLIIx Movie –

Dolby PLIIx Music –

Dolby PLIIx Matrix –

Dolby PLIIx Game –

Neo:6 Cinema –

Neo:6 Music –

The first section, ‘Stereo sources’ is the list of processing modes you wish to make available for stereo signals (analogue stereo, digital PCM stereo, Dolby 2.0, DTS 2.0, etc). When a stereo signal is applied, each press of the MODE button cycles through the processing modes you have enabled in the ‘Stereo sources’ section. The unprocessed Stereo option is always available for stereo signals therefore it is not shown in the list.

For Multichannel sources:

Stereo Downmix –

Dolby Digital EX –

Dolby PLIIx Movie –

Dolby PLIIx Music –

The second section, ‘Multichannel sources’ is the list of processing modes you wish to make available for multichannel digital signals (any Dolby or DTS digital stream that has more channels than stereo 2.0). When a multichannel digital signal is applied, each press of the MODE button cycles through the processing modes you have enabled in the ‘Multichannel sources’ section.

Zone Settings

Lists the volume and control settings for Zone 2 and Zone 3 (Zone 3 available with AVR600/AV888 only). These settings are applied to all audio inputs and are stored in memory and recalled each time the unit is powered up.

Z2 Audio Input – Selects the analogue audio to be routed to Zone 2.

Z2 Video Output – Selects the analogue video to be routed to Zone 2 for the current audio input.

Zone 2 Volume – The current volume in Zone 2.

Zone 2 Max. Vol – Limits the maximum volume setting the system can be turned up to in the Zone 2. This is a useful feature to prevent accidental overdriving of low power-handling speakers, for example.

Zone 2 Fixed Vol – The Zone 2 volume control can be locked at the current value for use with an external amplifier with its own volume control in Zone 2.

Zone 2 Max On Vol – Limits the maximum volume the system operates in the Zone 2 when it is switched on or comes out of Standby. The system comes on at this volume if the last used (possibly very loud) volume exceeds this value.

Zone 3 Volume – The current volume in Zone 3.

Zone 3 Max. Vol – Limits the maximum volume setting the system can be turned up to in the Zone 3. This is a useful feature to prevent accidental overdriving of low power-handling speakers (for example).

Zone 3 Fixed Vol – The Zone 3 volume control can be locked at the current value for use with an external amplifier with its own volume control in Zone 3.

Zone 3 Max On Vol – Limits the maximum volume the system operates in the Zone 3 when it is switched on or comes out of Standby. The system comes on at this volume if the last used (possibly very loud) volume exceeds this value.

Standby – When a Standby command is received by an infra-red eye in Zone 2, this setting controls which parts of the AVR500, AVR600 or AV888 to turn on and off:

When Local Only, the Standby IR command only affects the zone it was received in (Zone2 or Zone3).

When All Off, the Standby IR command affects the entire system in all zones.

Network

The AVR600 and AV888 are fitted with a network audio client (optional for the AVR500) which is capable of playing internet radio stations as well as stored music on a network storage device such as a PC, or on a USB flash drive.

Use DHCP – Select if your network uses DHCP

<No: To assign a fixed IP address manually.

<Yes: To use network parameters given by the DHCP server.

MAC address – (Information only) The unique address of the network card in your AVR500/AVR600/AV888.

IP Address – If not using DHCP, enter the IP address you have assigned to the AVR500/AVR600/AV888 for your network.

Subnet Mask – If not using DHCP, enter the subnet mask for the AVR500/AVR600/AV888 on your network.

Gateway – If not using DHCP, enter the IP address of the router the AVR500/AVR600/AV888 is connected to.

Primary DNS – If not using DHCP, enter the Primary DNS IP address of your internet service provider.

Alternate DNS – If not using DHCP, enter the Secondary DNS IP address of your internet service provider.

Use Proxy – Select if you connect to the network via a Proxy Server.

<No: If you connect directly onto the network.

<Yes: If you connect to the network via a Proxy Server.

Proxy Address – If connecting via a Proxy Server, enter its IP address.

Proxy Port – If connecting via a Proxy Server, enter the port number to which the Proxy responds.

E-44

Page 45 Page 47
Image 46
Page 45 Page 47
Contents AVR500 / AVR600 / AV888 N d b o o k AVR surround amplifier / AV processorSafety compliance Safety GuidelinesImportant safety instructions Class II productInstructions de sécurité importantes Class II produitRespect des consignes de sécurité Page DIY setup? ContentsProfessional Installation? WelcomeBefore you Begin… Placing the unit PowerStandby power Interconnect cablesTrademark acknowledgements Product differences and options GeneralMaking connections Component/RGB Video CompositeAVR600 AV888 Component/RGB video connectors Hdmi connectorsZone 3 connectors Zone 2 connectorsTape inputs ConnectorsDigital audio Phono Analogue audio MCH inputTrigger connectors Infra-red IR connectorsCD player DVD playerSatellite receiver Use the Composite connection if HdmiConnecting an iPod using the Arcam rDock AVR500 Video connectorsComponent, S-Video and Composite connectors, see Aerials, control and communicationAV, SAT, DVD Subwoofer outputs For more information on connecting speakers, seeFront panel Phones socket Trigger connectors VCR, Camcorder, Games Console etc Preferred video hook-up, in order of preference isConnecting an iPod using the Arcam rDock Sirius Radio ConnectorsAerial connectors AVR500/AVR600 only DAB optionConnecting an aerial RS232 serial connector Other ConnectorsData connectors Network connectors USB connector RLead/rDockSpeakers Connecting speakers AVR500 & AVR600Connecting subwoofers Speaker cablesFront left and right CentreSubwoofer Surround left and rightOperating your AVR500 /AVR600 / AV888 Switching onOperation Selecting a sourceUpdating firmware using a PC Using Zone 2Extended front panel menu Front panel Operation Inserting batteries into the remote control CR102 universal remote controllerUsing the remote control Device Mode / Source keys Useful informationControlling other devices Code blink-backIPod commands AMP AMP Device ModeOK selects/play the highlighted file Network commands TUN TUN Device ModeDVD DVD Device Mode Highlighted menu on the screenAV AV Device Mode SAT SAT Device ModeMenus PVR PVR Device Mode VCR VCR Device ModeShift + rcycles through the repeat CD CD Device ModeStarts Program mode Options track, disc, etcSpeaker Distances Essential SetupSpeaker types Speaker LevelsProblems Auto speaker SetupAuto speaker setup Using a subwooferSetup menus Navigating the setup menuSelecting the video source VideoSelecting the audio source Input Config Treble BassGeneral information and system controls General SetupPlii Dimension Plii Centre Width Plii Panorama Is usedSpkr Distance Auto SetupSpkr Types Spkr LevelsProgressive scan playback Video InputsVideo Outputs Important points to rememberNetwork Zone SettingsMode For Stereo sourcesEnglish Introduction Decoding ModesTwo-channel source modes Multichannel source modes Decoding modesDolby Volume is a sophisticated new SettingsVolume Leveller Calibration OffsetEnglish Deleting Presets Tuning/Channel SelectionSaving and selecting Presets Tuner OperationAdd to your subscription Sirius errorsDefault unlock code is OperationUSB playback Network/usb OperationSelecting the playback source Internet radio stationsEnglish XLR balanced line outputs AV888 only External AmplifiersAnalogue pre-amplifier outputs AVR600/AV888 only SW2, SW3Zone 3 AVR600/AV888 only Multi-room Set upZone Zone 2 and 3 control outputsMulti-room connection guide Zone EnglishCustomising CR102 Code LearningCreating Macros Volume punch-throughKey Mover To restore a moved Device Mode key to its original state Mode MoverLocking/Unlocking a specific Device Mode Copy a key between Device ModesMode key IR punch-through Resetting the CR102Problem Check that Switched off Volume is always too loudWhen I turn on Wired networkSpecifications Continual improvement policyClaims under guarantee Product GuaranteeWorldwide Guarantee Problems?Device code Tables HCM GBCGEC HYDRBM NU-TECOKI RCAAVP YU-MA-TUGPX NTL STSADB UPCAMW 3D LABAKI AtacomXMS TSMTVE AsciKPN HNEIdte SATSH222E Issue

AVR500 / AVR600 / AV888 specifications

The Arcam AVR500, AVR600, and AV888 are high-performance audio-video receivers that exemplify Arcam's commitment to delivering exceptional sound quality and versatility in home theater systems. Each model boasts a combination of advanced technologies, robust build quality, and a user-friendly interface, making them popular choices among audiophiles and home cinema enthusiasts.

The Arcam AVR500 is designed for those who appreciate high fidelity sound. It features a 7.1 channel amplifier delivering 100 watts per channel, allowing for immersive audio experiences. The AVR500 supports various audio formats, including Dolby TrueHD and DTS-HD Master Audio, ensuring that users can enjoy their favorite movies and music with rich, dynamic sound. The unit is equipped with extensive connectivity options, including multiple HDMI inputs and outputs, enabling seamless integration with other devices.

Moving up the line, the AVR600 enhances the AVR500's capabilities with additional power and features. It features a more powerful 120 watts per channel amplification and includes advanced room calibration technology known as Arc. This innovative feature optimizes audio playback by analyzing the room’s acoustics and adjusting the sound accordingly, helping to create a more immersive home theater experience. The AVR600 also supports 3D video pass-through and features HDMI 1.4 compatibility, making it future-proof for new video technologies.

At the pinnacle of this lineup, the Arcam AV888 takes a slightly different approach, focusing on becoming a premier preamp/processor that connects to external amplification. The AV888's superior processing ensures audiophiles experience the highest quality sound possible. With support for multi-channel PCM audio and a range of processing formats, users can experience the latest high-definition audio technologies. The unit houses advanced digital-to-analog converters for enhanced sound clarity and supports 4K video upscaling, making it an excellent choice for those invested in the latest visual standards.

All three models share a commitment to high-quality construction, ensuring durability and longevity. The user interface is intuitive, making navigation between functions seamless. This trio of receivers is compatible with various streaming services, allowing music to be enjoyed effortlessly from multiple sources.

In summary, the Arcam AVR500, AVR600, and AV888 provide exceptional sound quality, advanced features, and robust build quality, catering to an array of home entertainment needs. Whether for music or movies, these receivers promise rewarding and captivating listening experiences.
Top Page Image Contents