Arcam AVR500 / AVR600 / AV888 Operation, Operating your AVR500 /AVR600 / AV888, Switching on

Page 27

operation

Operating your

AVR500 /AVR600 / AV888

For information display we recommend you use the OSD (On-Screen Display) on your display device whenever possible.

Switching on

Press the front panel power button in. The power LED will glow orange, the front display shows the word ‘ARCAM’, followed by the volume setting and the name of the selected input. After initialization is complete, the power LED changes colour to green.

Please wait until the unit has finished initialising before operating the unit. It is recommended that if the unit is switched off, you should wait at least 10 seconds before switching the unit back on.

Standby

The unit has a standby mode which can be entered by pressing Standby on the remote control. When in standby mode, the display is blank and the power LED glows red.

While in Standby mode, it may be possible to hear a slight residual hum coming from the mains transformer inside the amplifier. This is perfectly normal. However, if the unit is to be left unused for an extended period, we recommend that you disconnect it from the mains supply to save power.

To switch on from standby

Press the standby button on the remote control or any key on the front panel (other than the power button).

Front panel display

The unit is ready for use after about four seconds.

The display window shows the currently selected source and the last selected information view setting (this information line can be changed using the INFO button).

The active zones (Z1, Z2 or Z3) are highlighted – the example screen above shows that only Z1 (i.e. Zone1) is active. The current volume setting (70.0dB in the above example) is also displayed.

Selecting a source

 

The MCH input is intended for direct analogue pass-

To select a particular source, press the –inputor

through of DVD Audio or SACD sources. Apart from

volume control and level trim, no processing modes

input + buttons until that source is shown on the front

are possible on this input, including bass management

panel display, or (if available) press the corresponding

and delays. Please set bass management, speaker size

source button on the remote. The following sources are

and speaker delays in the source player. You can copy

available:

 

 

the distances and relative speaker levels from the Setup

CD

Compact Disc player input

 

menus in the AVR500, AVR600 or AV888.

 

 

AV

Audio-Visual input

 

Tape operation (AVR600/AV888 only)

DVD

DVD player input

 

Three analogue audio outputs are provided for

SAT

Satellite receiver input

 

recording, VCR, PVR and Tape out. The selected analogue

 

input are routed to each of these outputs.

VCR

Video Cassette Recorder input

If the VCR input is selected, the VCR Out output

 

 

 

PVR

Personal Video Recorder input

is muted to prevent feedback loops in recording

Phono1

Phono (MM cartridge) input

equipment. Similarly the PVR Out and Tape Out outputs

MCH

Selects MCH (multichannel)

 

are muted when their respective inputs are selected to

 

prevent feedback.

 

 

 

analogue input

 

VCR operation (AVR600/AV888 only)

TAPE

Audio only tape deck input

 

 

Two outputs are provided for recording (Composite

AUX

Auxiliary (front panel) input

 

 

and S-Video only), VCR and PVR Out. The selected video

Net2

Internal (Ethernet) and external USB

input is routed to each of these outputs.

 

solid-state device (e.g. pen drive) input.

Stereo Direct

iPod

Requires an iPod® and Arcam rDock

To listen to a pure analogue stereo input, press the

 

or rLead.

 

The following sources are only available on the AVR500/

Direct button. The Stereo Direct mode automatically

bypasses all processing and any surround functions. In

AVR600:

 

 

 

 

direct mode, digital processing is shut down to improve

 

 

 

AM/FM

Internal tuner input

 

the sound quality and reduces digital noise with the unit

 

to an absolute minimum.

DAB3

Internal tuner input

 

 

Note: when Stereo Direct mode is selected, no

Sirius3

Requires an external receiver – see

digital output is available and no bass management

 

www.sirius.com for more information

is performed, meaning that bass signals will not be

1This source is not available on the AVR500.

 

redirected to a subwoofer.

2This source is optional on the AVR500. Contact your

Volume control

dealer for upgrade information.

 

 

It is important to realise that the level of the volume

3These sources are market dependent and may not be

indicator is not an accurate indication of the power

available on your unit.

 

 

delivered to your loudspeakers. The amplifier often

Upon selecting a source, the unit will normally select an

delivers its full output power long before the volume

active digital input in preference to an analogue input.

control reaches its maximum position, particularly when

If you want to override the digital input and select the

listening to heavily recorded music. In comparison,

analogue input, set the Audio Source to Analogue in the

some movie sound tracks can appear very quiet, as

Input Config. menu (see page

AM). Some/FM, inputs (many directors like to keep maximum levels in reserve

Phono, MCH, Sirius, iPod) do not have a digital input.

for special effect sequences.

The processing mode and Stereo Direct functions are remembered and recalled for each individual input.

English

E-25

Page 26 Page 28
Image 27
Page 26 Page 28
Contents N d b o o k AVR surround amplifier / AV processor AVR500 / AVR600 / AV888Class II product Safety GuidelinesImportant safety instructions Safety complianceClass II produit Instructions de sécurité importantesRespect des consignes de sécurité Page Welcome ContentsProfessional Installation? DIY setup?Before you Begin… Interconnect cables PowerStandby power Placing the unitTrademark acknowledgements Component/RGB Video Composite GeneralMaking connections Product differences and optionsAVR600 AV888 Zone 2 connectors Hdmi connectorsZone 3 connectors Component/RGB video connectorsMCH input ConnectorsDigital audio Phono Analogue audio Tape inputsInfra-red IR connectors Trigger connectorsUse the Composite connection if Hdmi DVD playerSatellite receiver CD playerConnecting an iPod using the Arcam rDock Aerials, control and communication Video connectorsComponent, S-Video and Composite connectors, see AVR500AV, SAT, DVD For more information on connecting speakers, see Subwoofer outputsFront panel Phones socket Trigger connectors Preferred video hook-up, in order of preference is VCR, Camcorder, Games Console etcConnecting an iPod using the Arcam rDock DAB option Radio ConnectorsAerial connectors AVR500/AVR600 only SiriusConnecting an aerial RLead/rDock Other ConnectorsData connectors Network connectors USB connector RS232 serial connectorSpeaker cables Connecting speakers AVR500 & AVR600Connecting subwoofers SpeakersSurround left and right CentreSubwoofer Front left and rightSelecting a source Switching onOperation Operating your AVR500 /AVR600 / AV888Using Zone 2 Updating firmware using a PCExtended front panel menu Front panel Operation CR102 universal remote controller Inserting batteries into the remote controlUsing the remote control Useful information Device Mode / Source keysCode blink-back Controlling other devicesAMP AMP Device Mode IPod commandsOK selects/play the highlighted file Highlighted menu on the screen TUN TUN Device ModeDVD DVD Device Mode Network commandsSAT SAT Device Mode AV AV Device ModeMenus VCR VCR Device Mode PVR PVR Device ModeOptions track, disc, etc CD CD Device ModeStarts Program mode Shift + rcycles through the repeatSpeaker Levels Essential SetupSpeaker types Speaker DistancesUsing a subwoofer Auto speaker SetupAuto speaker setup ProblemsNavigating the setup menu Setup menusVideo Selecting the video sourceSelecting the audio source Treble Bass Input ConfigIs used General SetupPlii Dimension Plii Centre Width Plii Panorama General information and system controlsSpkr Levels Auto SetupSpkr Types Spkr DistanceImportant points to remember Video InputsVideo Outputs Progressive scan playbackFor Stereo sources Zone SettingsMode NetworkEnglish Decoding Modes IntroductionTwo-channel source modes Decoding modes Multichannel source modesCalibration Offset SettingsVolume Leveller Dolby Volume is a sophisticated newEnglish Tuner Operation Tuning/Channel SelectionSaving and selecting Presets Deleting PresetsOperation Sirius errorsDefault unlock code is Add to your subscriptionInternet radio stations Network/usb OperationSelecting the playback source USB playbackSW2, SW3 External AmplifiersAnalogue pre-amplifier outputs AVR600/AV888 only English XLR balanced line outputs AV888 onlyZone 2 and 3 control outputs Multi-room Set upZone Zone 3 AVR600/AV888 onlyZone English Multi-room connection guideCode Learning Customising CR102Volume punch-through Creating MacrosKey Mover Copy a key between Device Modes Mode MoverLocking/Unlocking a specific Device Mode To restore a moved Device Mode key to its original stateResetting the CR102 Mode key IR punch-throughProblem Check that Wired network Volume is always too loudWhen I turn on Switched offContinual improvement policy SpecificationsProblems? Product GuaranteeWorldwide Guarantee Claims under guaranteeDevice code Tables HYD GBCGEC HCMRCA NU-TECOKI RBMYU-MA-TU AVPGPX UPC STSADB NTLAtacom 3D LABAKI AMWAsci TSMTVE XMSSAT HNEIdte KPNSH222E Issue

AVR500 / AVR600 / AV888 specifications

The Arcam AVR500, AVR600, and AV888 are high-performance audio-video receivers that exemplify Arcam's commitment to delivering exceptional sound quality and versatility in home theater systems. Each model boasts a combination of advanced technologies, robust build quality, and a user-friendly interface, making them popular choices among audiophiles and home cinema enthusiasts.

The Arcam AVR500 is designed for those who appreciate high fidelity sound. It features a 7.1 channel amplifier delivering 100 watts per channel, allowing for immersive audio experiences. The AVR500 supports various audio formats, including Dolby TrueHD and DTS-HD Master Audio, ensuring that users can enjoy their favorite movies and music with rich, dynamic sound. The unit is equipped with extensive connectivity options, including multiple HDMI inputs and outputs, enabling seamless integration with other devices.

Moving up the line, the AVR600 enhances the AVR500's capabilities with additional power and features. It features a more powerful 120 watts per channel amplification and includes advanced room calibration technology known as Arc. This innovative feature optimizes audio playback by analyzing the room’s acoustics and adjusting the sound accordingly, helping to create a more immersive home theater experience. The AVR600 also supports 3D video pass-through and features HDMI 1.4 compatibility, making it future-proof for new video technologies.

At the pinnacle of this lineup, the Arcam AV888 takes a slightly different approach, focusing on becoming a premier preamp/processor that connects to external amplification. The AV888's superior processing ensures audiophiles experience the highest quality sound possible. With support for multi-channel PCM audio and a range of processing formats, users can experience the latest high-definition audio technologies. The unit houses advanced digital-to-analog converters for enhanced sound clarity and supports 4K video upscaling, making it an excellent choice for those invested in the latest visual standards.

All three models share a commitment to high-quality construction, ensuring durability and longevity. The user interface is intuitive, making navigation between functions seamless. This trio of receivers is compatible with various streaming services, allowing music to be enjoyed effortlessly from multiple sources.

In summary, the Arcam AVR500, AVR600, and AV888 provide exceptional sound quality, advanced features, and robust build quality, catering to an array of home entertainment needs. Whether for music or movies, these receivers promise rewarding and captivating listening experiences.
Top Page Image Contents