Shure DP11EQ manual Response Graph, Cutting, Copying, and Pasting Parametric Filters

Page 20

Response Graph

This section describes how to use the Response Graph, which displays the frequency response for the DP11EQ.

Snapshots

A helpful feature of the response graph is the ability to take snapshots of a frequency response curve. A snapshot allows you to view a trace of the original response curve while making changes. This is an effective setup tool. In the illustration above, the upper curve is the frequency response of the current settings, while the lower curve is the snapshot of the previous settings.

In order to use a snapshot:

1.Click on the TAKE button.

2.Click on the SHOW button.

3.Make changes to the filter or equalizer settings.

NOTE: If there have been no changes to the curve since the snapshot was originally taken, it might appear as though no snapshot has been taken. This happens because the snapshot and the current curve are exactly the same, so one is hidden under the other. Once you make changes, the current curve will change and you will be able to see the snapshot underneath.

Cutting, Copying, and Pasting Parametric Filters

Cutting a Selected Parametric Filter

1.Click on the desired parametric filter.

2.Click on Edit in the main menu.

3.Click on Cut.

Copying a Selected Parametric Filter

1.Click on the desired parametric filter.

2.Click on Edit in the main menu bar.

3.Click on Copy.

Pasting a Selected Parametric Filter

1.Cut or Copy the desired parametric filter.

2.Go to the unit and equalizer section where you would like to place the filter.

3.Click on Edit in the main menu bar.

4.Click on Paste.

English ±19

Image 20
Contents DP11EQ Table of Contents Introduction Hardware FeaturesSoftware Features DP11EQ Hardware OverviewFront Panel BackDIP Switches Shure Link Device IDSubgroup Insert Audio ConnectionsMain Amplifier Input Insert Connecting the DP11EQ to a Computer via the RS-232 COM Port Software InstallationDP11EQ Software IntroductionShure Program Group Configuring the Computer Serial PortAccessing the Connected DP11EQs Overview Main Controls Processor Select ButtonsDynamics Processor Dynamics Parameters Expander Dynamics ProcessesGate AGC Leveler Compressor LimiterSnapshots Editing Dynamics ProcessesParametric Equalizer High- and Low-Frequency Shelf/Cut Filters Setting and Adjusting Parametric FiltersParametric Equalizer Edit Boxes and Controls Response Graph Cutting, Copying, and Pasting Parametric FiltersIN/OUT Meters and Output Control Meter CalibrationDelay for Solving Phase Cancellation Problems DelayDelay for Solving Remote Speaker Alignment Setting Delay by Distance Reversing the Output Signal PolaritySetting Delay by Time Shure Link Networks Shure Link ConnectionsShure Link Options Shure Link Device MenuMaintenance ScenesSettings To Save Settings to DiskTo Recall Settings from Disk Customizing Graph ColorsAppendix A. Specifications Printing DP11EQ SettingsLocking Out the Front Panel Exiting the DP11EQ ApplicationDelay Appendix B. Rack Mounting the DP11EQ Single UnitDual-Mounted Units Mounting in an Equipment RackAudio Cables Appendix C. Connectors and CablesAudio Connectors In. to 1/4 -in. Balanced In. to 1/4 -in. UnbalancedIn. Balanced to 1/4 -in. Unbalanced XLR male to 1/4 -in. BalancedRCA to 1/4 -in. Unbalanced XLR female to 1/4 -in. BalancedXLR female to 1/4 -in. Unbalanced Digital Connectors and Cables Computer Interface Ð 9-Pin to 9-Pin RS-232 CableComputer Interface Ð 9-Pin to 25-Pin RS-232 Cable Shure Link Cable Ð 5-Pin DIN Cable MIDI-compatible cableAppendix D. Keyboard Controls General ControlsIN/OUT Meters and Output Slider Controls Parametric Equalizer Controls