Shure manual DP11EQ Hardware, Overview, Front Panel, Back

Page 4

DP11EQ HARDWARE

Overview

Front Panel

 

 

DATA

Ê ￿ ￿

￿

￿ ￿

Ê BYPASS Button and LED. Press this button to

￿ Dynamic Gain Meters. The 7 red LEDs on the left

suspend all signal processing from the audio path. When the LED illuminates, the dynamics processor, delay, and the equalizers are bypassed.

indicate the reduction in dynamic range, while the three yellow LEDs on the right indicate dynamic boost.

￿

￿

SIGNAL LED. Illuminates when input signal is

￿ DATA LED. This LED indicates that the computer

is communicating with the unit via the RS-232 port.

present. Intensity varies with input signal level.

 

CLIP LED. Illuminates when the input signal is

￿ POWER LED. LED illuminates when unit is

within 6 dB of clipping.

powered on.

Back

Ê ￿ ￿

ÊPower Connector with Integral Fuse. Connects to AC power. The fuse is located in the drawer below the connector.

￿9-PinRS-232 Port. Connects the unit to a computer. For use with DP11EQ software and for DSP firmware upgrades.

￿Shure Link Interface. Allows linking of up to 16 Shure Link compatible devices which may be accessed by a single computer.

￿DIP Switches. See DIP Switches.

￿ ￿ ￿

￿Output ConnectorÐ1/4-Inch & XLR. Active, cross-coupled, balanced outputs can be used with balanced or unbalanced inputs. Can be switched

between +4 dBu/±10 dBV line-level operation by DIP switch. 1/4-Inch and XLR are driven independently and either can be balanced or unbalanced without affecting the other.

￿Input ConnectorÐCombined XLR and

1/4-Inch.Active balanced input can be used with balanced or unbalanced outputs. Can be switched between +4 dBu/±10 dBV line-level operation by DIP switch.

English ± 3

Page 3 Page 5
Image 4
Page 3 Page 5
Contents DP11EQ Table of Contents Software Features Hardware FeaturesIntroduction DP11EQ Hardware OverviewFront Panel BackDIP Switches Shure Link Device IDMain Amplifier Audio ConnectionsSubgroup Insert Input Insert Connecting the DP11EQ to a Computer via the RS-232 COM Port Software InstallationDP11EQ Software IntroductionAccessing the Connected DP11EQs Configuring the Computer Serial PortShure Program Group Overview Main Controls Processor Select ButtonsDynamics Processor Dynamics Parameters Gate Dynamics ProcessesExpander AGC Leveler Compressor LimiterSnapshots Editing Dynamics ProcessesParametric Equalizer Parametric Equalizer Edit Boxes and Controls Setting and Adjusting Parametric FiltersHigh- and Low-Frequency Shelf/Cut Filters Response Graph Cutting, Copying, and Pasting Parametric FiltersIN/OUT Meters and Output Control Meter CalibrationDelay for Solving Remote Speaker Alignment DelayDelay for Solving Phase Cancellation Problems Setting Delay by Time Reversing the Output Signal PolaritySetting Delay by Distance Shure Link Networks Shure Link ConnectionsShure Link Options Shure Link Device MenuMaintenance ScenesSettings To Save Settings to DiskTo Recall Settings from Disk Customizing Graph ColorsAppendix A. Specifications Printing DP11EQ SettingsLocking Out the Front Panel Exiting the DP11EQ ApplicationDelay Appendix B. Rack Mounting the DP11EQ Single UnitDual-Mounted Units Mounting in an Equipment RackAudio Connectors Appendix C. Connectors and CablesAudio Cables In. to 1/4 -in. Balanced In. to 1/4 -in. UnbalancedIn. Balanced to 1/4 -in. Unbalanced XLR male to 1/4 -in. BalancedXLR female to 1/4 -in. Unbalanced XLR female to 1/4 -in. BalancedRCA to 1/4 -in. Unbalanced Digital Connectors and Cables Computer Interface Ð 9-Pin to 9-Pin RS-232 CableComputer Interface Ð 9-Pin to 25-Pin RS-232 Cable Shure Link Cable Ð 5-Pin DIN Cable MIDI-compatible cableAppendix D. Keyboard Controls General ControlsIN/OUT Meters and Output Slider Controls Parametric Equalizer Controls
Top Page Image Contents