JVC VN-C625 manual Output Requirements

Page 17

⬛ Alarm Output Terminal

Connect this terminal to alarm devices such as an annunciator, indicator, lamp or buzzer.

VN-C625

(Alarm Output Equivalent Circuit)

			Alarm Device
			Connection
			Example
	OUT		DC 12 V
	OUT	IN	R
	Terminal	IN	R
	Grounding
	Terminal
		GND

Output Requirements

•Equivalent to NPN open collector output (Set output logic using the controller)

•Allowed applied voltage: DC12V and below

•Allowed input current: 50 mA

•Momentary output: 1 to 5000ms (Set duration using the controller)

Caution

Connect the grounding terminal of VN-C625 to the GND terminal of the alarm device.

3. Connection of LAN Cables

Use the LAN cable to connect this camera to a hub or PC

When connecting to a hub make use of a straight cable. When connecting to a PC make use of a cross cable.

Caution

The use of a cross cable may not be supported by certain LAN boards on some rare occasions. As such, please check your LAN board specifications before connection.

Note

When using 100 BASE-TX, ensure to use a Category 5 (or higher) cable.

17

Image 17

Contents VN-C625 Safety Precautions Important Safeguards Preparation Settings Contents IntroductionOperating Using the V.Networks Controller Setting Using the V.Networks ControllerOperating Using a Web Browser OperationOperating Precautions Characteristics Zooming operation Consumable PartsOperating Precautions PC Specifications Latest UpdatesItems Included Operating EnvironmentName and Function of Parts Ceiling Mount Camera Terminal Side Fastening Hook for Safety WireClamping Holes x # Camera Clamping BracketLAN Connection Connection ExamplesNetwork Connection Peer-to-Peer ConnectionSet the camera in the following procedure Preparation ProcedureRemove the cover Connecting CablesMake a hole in the ceiling Attach the cover Lead the cable through the coverConnect the cable to this camera Alarm Input Terminal Connecting CablesCable Specifications Output Requirements Connection of Coaxial Cables Connecting a 5C-2V or 3C-2V coaxial cableConnecting multiple VN-C625 Cameras Disconnect the connector from the sup- plied Converter UnitAttachment of Ceiling Mount Attach safety wire to prevent camera from falling downFront List of Tested CF Cards Inserting the CF cardAttach the CF cover dismantled in Step Installing the Camera Fasten the locking screw Installing the CameraTurn the camera Installing the VN-C625U Setup Tool Installing the SoftwareInstalling the V.Networks Controller Click Setting PCs IP Address Windows XPClick on the Local Area Connection Properties screen Select Internet Protocol TCP/IP and click PropertiesSetting PCs IP Address Windows Click Settings Network Settings Start up the V.Networks Controller. Check settingsOther Settings Using the VN-C625U Setup Tool Following confirmation screen will be displayed Authorization Level Allowed AccessMulticast Other Settings Using the VN-C625U Setup Tool 2. MulticastV.Networks Search screen is displayed Start up the VN-C625U Setup ToolMulticast Address Search screen is displayed Search result is displayedStart up the VN-C625U Setup Tool and select Alarm Alarm InputOperation when an alarm input is activated Page Detect Mode Alarm 1/AlarmAlarm Output Go to a presetAlarm FTP Alarm 1/Alarm Message PacketRelay Alarm AvailablePosition Return Mode Preset Position Other Triggers List Alarm Output Example Setting the Trigger Recording screenSetting the Frame Rate screen Recording files Setting the Advance screenRecording time When all the settings have been completed, click to end Start up the VN-C625U Setup Tool and select Private MaskWhen setting is complete, click Free area Fixed areaPerform area setting Displaying still images uploaded to the /user folder Other Settings Using the VN-C625U Setup Tool 8. WebStart up the VN-C625U Setup Tool and select FTP Server Other Settings Using the VN-C625U Setup Tool 9. FTP ServerRec File Continuous FTPTrigger FTP Error recovery Connection error PasswordTransfer error Alarm FTP Upload SettingTime Mode Black and WhiteLight One Push AFAuto Level When NTP is used Start up the VN-C625U Setup Tool and select TimeStart up the VN-C625U Setup Tool and select Auto Return Start up the VN-C625U Setup Tool and select Memory InfoHigh Speed NormalConnect to VN-C625 Starting Up V.Networks Controller Settings Setting Using the V.Networks ControllerFeatures that Allow Setting Using the V.Networks Controller 5Help About Features that Allow Setting Using the V.Networks Controller4Setting Quality Select File and Motion Detection Standby Select a camera Motion Detection StandbyImage Size and Inversion Select View Specify Image Size and Upside Down settingsImage Quality Setting Image Quality Setting Image Quality Setting Large Peak value Average PeakSet value ShutterImage Quality Setting Lens Frame Rate Select Setting and Frame rate Set the Frame RateSelect Setting and Position Memory Preset Position SettingAlarm Setting Alarm Setting Pan/Tilt Speed Pan/Tilt SettingVariable Speed 1 to SpeedSelect Setting and Auto Pan Setting Auto Pan SettingClose the window Perform settingSelect Setting and Auto Patrol Setting Auto Patrol SettingAuto Patrol No Start to memorize operation Auto Trace SettingSelect Setting and Auto Trace Setting Close the window Time Stamp Select Setting and Time Stamp Perform settingChanging Registered Information Select Setting and Property Perform settingWhen alteration is complete, click Snap Shot Buttons for position movingPan/Tilt button # Pan/Tilt/Zoom Position IndicatorZoom button and Zoom bar Angle StepClick the REC button Record/StopClick the Stop button Motion Image WindowPlayback Playback Click Playback screen is displayed Image Size Data Size Per Image Approximate Recording Time Record/Playback TimeClick the Snap Shot button SnapshotSnap screen will be displayed Save As screen is displayedWeb Page Images LAN EnvironmentAuthentication of Access Authorization Access Authorization LevelTop page will be displayed Starting Up the Web BrowserStart up the web browser Top Setting Using the Web BrowserDisplay the Top Settings page will be displayed Other settings Setting Using the Web Browser 1. Other SettingsSetting Using the Web Browser 1. Other Settings # NTP Settings Http port number, check using the setup tool suppliedSetting Using the Web Browser 2. Control Setting Using the Web Browser 3.Image Setting AGC Iris ModeManual Focus Level AveragePeakAccording to ZOOM, speed of operation is made variable Setting Using the Web Browser 4. PAN/TILT Setting1Low, 2 to 7, 8Fast Image Settings Screen Setting Using the Web Browser 5. Position Memory Setting100 Setting Using the Web Browser 6. View SettingResolution 101 Setting Using the Web Browser 7. Alarm Setting Alarm Out 103 Setting Using the Web Browser 8. FTP SettingSetting Using the Web Browser 8. FTP Setting Setting Using the Web Browser 9. Auto Pan Setting Position Number Setting Using the Web Browser 10. Auto Patrol SettingDuration 106Record Start Confirmation Screen Image Settings Screen Setting Using the Web Browser 11. Auto Trace SettingFor setting image quality 107108 Setting Using the Web Browser 12. Black & White SettingSetting Using the Web Browser 13. Schedule Setting Mask Position and Size Controller 109 Setting Using the Web Browser 14. Private Mask SettingFunction Setting Using the Web Browser 15. Limit SettingRight Side Left Side Tilt Limit111 Setting Using the Web Browser 16. Auto Return SettingReturn Action 112 Viewing Still Images113 Viewing Live Images114 Image LinkDisplaying a still image 115 TroubleshootingSymptom Causes/Remedial Actions 116 TroubleshootingCamera Rotating Table Pan/Tilt Mechanism SpecificationsLens General Ceiling Mount Hole Unit mm Dome Type Network Camera VN-C625