JVC VN-C625 manual Disconnect the connector from the sup- plied Converter Unit

Page 19

5. Connection of Conveter Unit

Press	Power cable
2.	5mm
2.	Press
1.	Connector
Press

3.

to AC 24V

4.

Connect the camera to AC 24 V.

1. Disconnect the connector from the sup- plied Converter Unit.

It can be disconnected by pressing both ends as shown in the left figure.

2. Mount the power cable to the connector. Strip the cover of the power cable (about 5 mm), while pressing down the arrow portion using a flat screwdriver, insert it into the con- nector.

3. Mount the connector.

4. Connect the supplied Converter Unit to the DC 12 V input terminal on the terminal stand.

When a 2-conductor VVF (Vinyl-insulated vinyl-sheath cable) is used, the maximum connection length is as shown below. (These are merely the standard reference values.)

Maximum cable length	80 m	210 m	330 m	560 m
Wire diameter (mm)	1.0 or more	1.6 or more	2.0 or more	2.6 or more

Caution

•Connect with the appropriate power-supply voltage.The rated voltage for VN-C625 (Converter Unit) is AC 24 V, 50 Hz/60 Hz and shall be Class 2.

If a voltage exceeding the rating is supplied, malfunction, or in the worst case, fuming or fire, may be caused.

•Installation shall be performed by qualified personnel according to regulations of individual regions.

Notes

Connecting multiple VN-C625 Cameras

In a system where more than 1 VN-C625 is used, turn on the power for a VN-C625 first, followed by setting the camera until "2-3 Setting IP Address for this Camera Using the 'VN-C625U Setup Tool' " is completed. Upon doing so, turn on a second camera and perform setting in the same way. Perform the same procedure for subsequent cameras.

•Default IP address setting for all VN-C625 cameras is 198.168.0.2.When the power for multiple cameras are turned on at one time under a single LAN environment, therefore, proper access may not be established due to IP address redundancy. Do not turn on the power of more than 1 camera at the same time.

•When IP address redundancy occurs, ensure that only one VN-C625 exists under a single LAN environment, and wait for some time (at least 10 minutes). In some cases, the power for all network devices under the same LAN environment may have to be turned off and on again to enable access to VN-C625.

19

Image 19

Contents VN-C625 Safety Precautions Important Safeguards Preparation Settings Contents IntroductionOperation Setting Using the V.Networks ControllerOperating Using the V.Networks Controller Operating Using a Web BrowserOperating Precautions Characteristics Zooming operation Consumable PartsOperating Precautions Operating Environment Latest UpdatesPC Specifications Items IncludedName and Function of Parts # Camera Clamping Bracket Fastening Hook for Safety WireCeiling Mount Camera Terminal Side Clamping Holes xPeer-to-Peer Connection Connection ExamplesLAN Connection Network ConnectionSet the camera in the following procedure Preparation ProcedureMake a hole in the ceiling Connecting CablesRemove the cover Connect the cable to this camera Lead the cable through the coverAttach the cover Cable Specifications Connecting Cables Alarm Input Terminal Output Requirements Connection of Coaxial Cables Connecting a 5C-2V or 3C-2V coaxial cableConnecting multiple VN-C625 Cameras Disconnect the connector from the sup- plied Converter UnitAttachment of Ceiling Mount Attach safety wire to prevent camera from falling downFront Attach the CF cover dismantled in Step Inserting the CF cardList of Tested CF Cards Installing the Camera Turn the camera Installing the CameraFasten the locking screw Installing the V.Networks Controller Installing the SoftwareInstalling the VN-C625U Setup Tool Click Setting PCs IP Address Windows XPClick on the Local Area Connection Properties screen Select Internet Protocol TCP/IP and click PropertiesSetting PCs IP Address Windows Click Settings Network Settings Start up the V.Networks Controller. Check settingsOther Settings Using the VN-C625U Setup Tool Following confirmation screen will be displayed Authorization Level Allowed AccessMulticast Other Settings Using the VN-C625U Setup Tool 2. MulticastSearch result is displayed Start up the VN-C625U Setup ToolV.Networks Search screen is displayed Multicast Address Search screen is displayedOperation when an alarm input is activated Alarm InputStart up the VN-C625U Setup Tool and select Alarm Page Go to a preset Alarm 1/AlarmDetect Mode Alarm OutputAvailable Alarm 1/Alarm Message PacketAlarm FTP Relay AlarmList Preset PositionPosition Return Mode Other Triggers Alarm Output Setting the Frame Rate screen Setting the Trigger Recording screenExample Recording time Setting the Advance screenRecording files When all the settings have been completed, click to end Start up the VN-C625U Setup Tool and select Private MaskWhen setting is complete, click Free area Fixed areaPerform area setting Displaying still images uploaded to the /user folder Other Settings Using the VN-C625U Setup Tool 8. WebStart up the VN-C625U Setup Tool and select FTP Server Other Settings Using the VN-C625U Setup Tool 9. FTP ServerTrigger FTP Continuous FTPRec File Alarm FTP Upload Setting PasswordError recovery Connection error Transfer errorTime Mode Black and WhiteAuto Level One Push AFLight When NTP is used Start up the VN-C625U Setup Tool and select TimeStart up the VN-C625U Setup Tool and select Auto Return Start up the VN-C625U Setup Tool and select Memory InfoHigh Speed NormalConnect to VN-C625 Starting Up V.Networks Controller Settings Setting Using the V.Networks ControllerFeatures that Allow Setting Using the V.Networks Controller 4Setting Quality Features that Allow Setting Using the V.Networks Controller5Help About Select File and Motion Detection Standby Select a camera Motion Detection StandbyImage Size and Inversion Select View Specify Image Size and Upside Down settingsImage Quality Setting Image Quality Setting Image Quality Setting Shutter Average PeakLarge Peak value Set valueImage Quality Setting Lens Frame Rate Select Setting and Frame rate Set the Frame RateSelect Setting and Position Memory Preset Position SettingAlarm Setting Alarm Setting Speed 1 to Speed Pan/Tilt SettingPan/Tilt Speed VariableSelect Setting and Auto Pan Setting Auto Pan SettingClose the window Perform settingSelect Setting and Auto Patrol Setting Auto Patrol SettingAuto Patrol No Select Setting and Auto Trace Setting Auto Trace SettingStart to memorize operation Close the window Time Stamp Select Setting and Time Stamp Perform settingWhen alteration is complete, click Select Setting and Property Perform settingChanging Registered Information Snap Shot Buttons for position movingAngle Step # Pan/Tilt/Zoom Position IndicatorPan/Tilt button Zoom button and Zoom barMotion Image Window Record/StopClick the REC button Click the Stop buttonPlayback Playback Click Playback screen is displayed Image Size Data Size Per Image Approximate Recording Time Record/Playback TimeSave As screen is displayed SnapshotClick the Snap Shot button Snap screen will be displayedWeb Page Images LAN EnvironmentAuthentication of Access Authorization Access Authorization LevelStart up the web browser Starting Up the Web BrowserTop page will be displayed Display the Top Setting Using the Web BrowserTop Settings page will be displayed Other settings Setting Using the Web Browser 1. Other SettingsSetting Using the Web Browser 1. Other Settings # NTP Settings Http port number, check using the setup tool suppliedSetting Using the Web Browser 2. Control Setting Using the Web Browser 3.Image Setting AveragePeak Iris ModeAGC Manual Focus Level1Low, 2 to 7, 8Fast Setting Using the Web Browser 4. PAN/TILT SettingAccording to ZOOM, speed of operation is made variable Image Settings Screen Setting Using the Web Browser 5. Position Memory SettingResolution Setting Using the Web Browser 6. View Setting100 101 Setting Using the Web Browser 7. Alarm Setting Alarm Out 103 Setting Using the Web Browser 8. FTP SettingSetting Using the Web Browser 8. FTP Setting Setting Using the Web Browser 9. Auto Pan Setting 106 Setting Using the Web Browser 10. Auto Patrol SettingPosition Number Duration107 Setting Using the Web Browser 11. Auto Trace SettingRecord Start Confirmation Screen Image Settings Screen For setting image qualitySetting Using the Web Browser 13. Schedule Setting Setting Using the Web Browser 12. Black & White Setting108 Mask Position and Size Controller 109 Setting Using the Web Browser 14. Private Mask SettingTilt Limit Setting Using the Web Browser 15. Limit SettingFunction Right Side Left SideReturn Action Setting Using the Web Browser 16. Auto Return Setting111 112 Viewing Still Images113 Viewing Live ImagesDisplaying a still image Image Link114 Symptom Causes/Remedial Actions Troubleshooting115 116 TroubleshootingGeneral SpecificationsCamera Rotating Table Pan/Tilt Mechanism Lens Ceiling Mount Hole Unit mm Dome Type Network Camera VN-C625