Panasonic AW-F575E manual Remote Control Unit Rack Mount Frame WV-Q70, OUTPUT-VIDEO 1, Video

Page 10

Note: When using the Remote Control Box (RCB) in the Remote Control Unit (RCU), the recording start/stop function is not avallable.

143.Intercom Level control (INTERCOM LEVEL)

Use this control to adjust the volume level in the head- set connected to the Intercom Jack (140)

143.Gen-lock Input Connectors (BNC) (GEN-LOCK IN AUTO 75Ohm./Hi-Z OUT)

These connectors receive the gen-lock signal (black burst or composite) from the Special Ettects Generator for system reference.

When connecting a coaxial cable with BNC connector to this connector, this connector is automatically termi- nated with 75 ohms.

Caution: As this connector is in parallel connection with the Remote Control Box Gen-lock Input Connector (155), do not input gen-lock signals to both of these connectors simultaneously

144.Auxiliary Input Connectors

(AUX IN-AUTO/75Ohm. Hi-Z OUT)

These connectors receive the lineview signal from a Special Effects Generator. Two connectors are provid- ed for bridging or looping application

When connecting a coaxial cable with BNC connector to this connector, this connector is automatically termi- nated with 75 ohms

145.Red, Green and Blue Output Connectors (OUTPUT-R/PR/C, G/Y/Y, B/PB/B)

Signals supplied from these connectors are selected by the RCU/VTR Signal Selection Switch (69) on the Camera Adaptor. Refer to page 47 tor setting the RCU/VTR Selection Switch.

Note: The RCU/VTR Signal Selection Switch (69) on the Camera Adaptor has been set to the ENC position at the factory

146.Video Output Connectors

(OUTPUT-VIDEO 1, VIDEO 2)

These connectors supply a composite video signal to a Special Effects Generator, a Video Monitor or a VTR Note: This connector is in parallel connection with the

Monitor Output Connector (154) on the Remote Control Box (RCB).

147. Sync Output Connector (SYNC OUTPUT)

This Connector supplies a negative 4Vp-p/75 sync signal to the Sync Input of an RGB Colour Video Monitor tor synchronization.

148. S-Video Output Connector (S-VIDEO)

This connector outputs the Y/C signal when the RCU/VTR Signal Selection Switch (69) on the camera adaptor is set to the Y/C/B Position

149.Tally and Intercom lnput Connector

(TALLY & INTERCOM)

Connect a 4-pin cable between this connector and the Tatty and Intercom Output ot the Speclal Effects Generator

150.Fuse (250V 1,25A)

151.Multiplex Connector (MPX)

This c o n n e c t o r is c o n n e c t e d t o t h e Multiplex

Connectorsigna1 ot the camera with coaxial cable (5C-2V or equal)

Note: When using this connector. set the Cable Selection Switch (152) to MPX position

152.Cable Selection Switch

(CABLE SELECT, MULTI/MPX)

Set this switch to the MULTI or MPX position accord- ing to the control cable used.

MULTI: Select this position when the 26-pin cable (Multi cable) is used to control the camera

MPX: Select this position when the coaxial cable (5C- 2V) is used to control the camera

Caution: Do not use the multi-cable and the coaxial cable together

153.Multi-cable Connector (CAMERA)

This connector is connected with the VTR/RCU Connector (41) by using the multi-cable (26-pin)

Note: Be sure to Set the Cable Selection Switch (152) to the MULTI position.

154. Monitor Output Connector of the Remote Control Box (RCB)

As this connector is in parallel connection with the OUTPUT-VIDEO 2 Connector (146). do not output the signal slmultaneously from both connectors.

155.Gen-lock Input Connector of Remote Control Box This connector is used to input the gen-lock signal to the Remote Control Box when using the Remote Control Box extended trom the Remote Control Unit

156.Remote Control Unit Extension Connector

This connector is used to extend the Remote Control Box from the Remote Control Unit or from the camera by using the optional RCB cable (WV-CA10B02/WV- CA10B25/WV-CA10B50)

The maximum cable length for the extension is 100m (300 tt)

Refer to the following table

157. Remote Control Unit Connector

This connector is used for directly connecting with the Remote Control Box Connector (159) on the Remote Control Unit.

158.Not used

159.Remote Control Box Connector

This connector is connected directly with the Remote Control Unit Connector (157) on the Remote Control BOX.

160. Remote Control Box

Extension Connector

This is c o n n e c t e d to

t h e Remote

C o n t r o l Unit

Extension Connector (156) on the Remote Control Box

by using the optional cable.

 

Refer to Item 156 tor more details.

 

161. Control Connector (CONTROL)

 

This connector is connected with the

control connec-

tor ot the pan/tilt unit or lens control by using the multi- cable (15-pin)

 

 

 

 

 

DEFROSTER

2 5V

0

WIPER

2 5V

 

0

Lens Control Voltage

162. Audio Output Jack (AUDI0 OUT)

By setting the Audio Level Selection Switch of the

Camera Adaptor AW-AD700BSE

to the -20 dB posi-

tion, the audio output is available.

 

 

 

 

Note: In case of Multiplex or VP

Multiplex operation,

s e t t h e Audio Level Selection

Switch o f

t h e

Camera Adaptor AW-AD700BSE

to the -20

dB

position. Me Switch 1 on the Audio

Board in side

the Camera Adaptor AW-AD700BSE

and Switch 2

on the MOD board inside this unlt

to the AUDI0

position for the Audio Output function to be acti- vated

REMOTE CONTROL UNIT RACK

MOUNT FRAME WV-Q70

165. Rack-mounting Spacer

This is used when mounting a single Remote Control Unit in a rack

166. Rack-mounting Angles

These two Rack-mounting Angles are used for mount- ing two Remote Control Units side by side in a rack

167. Remote Control Unit Joining Bar

These bars are used to join two Remote Control Units together.

- 22 -

Note: As the video level is changed by using various cable lengths, under certain conditions it may be out of the specification for the AW-F575E.

Note: The impedance for the control voltage should be 2 kohms or less

- 23 -

Image 10
Contents AW-F575E Camera Head AW-F575HE Lens Iris Selection SwitchMajor Operating Controls and Their Functions Auto Iris Serfvo Control Zoom LensON/OFF Scene FILE, User A/B/1/2/3Back Light Comp ON/OFF DTL, LEVEL-HIGH/LOW/OFFBAR/N.E/CAMERA Camera Adaptor AW-ADS00AEAUTO/ATW ATW/A/B Signal Select Earphone OUT SEL, INT/PBIncom Earphone 14X Servo Control Zoom Lens AW-LZ14ST73 Remote Control Unit WV-RC7OOA Electronic Viewfinder WV-VF42RCB AWC/HOLD/ABCOUTPUT-VIDEO 1, Video Remote Control Unit Rack Mount Frame WV-Q70Cable SELECT, MULTI/MPX Night EYE, HIGH/LOW/OFF Remote Control Unit WV-RC550AUTO/ATW, ATW/A/B Up Switch UP Electronic Shutter Selection SwitchDown Switch Down Item Switch ItemElectronic Viewfinder WV-VF65B Lens Control KIT WV-LK35Lens Control KIT WV-LK36 Tripod Mounting Adaptor WV-QT700 Carrying Case WV-CC500AInstallatìon of the Optional Mìcrophone Holder InstallationXLR type Microphone Connector Microphone Information Mounting the Camera AdaptorMounting the 1.5 Electronic Viewfinder Mounting the 5 Electronic ViewfinderInstallation of the AC Adaptor/Charger WV-PS34 Mounting of the Betacam Format VTRMounting on the Tripod Mounting Adaptor Removing the VTR from the CameraAttaching the Shoulder Strap Connection with the VTR Connection with the Remote Control BoxSystem Connection Connection with a sub-VTR back-up VTRPC Mode System OUTVTR Operating Procedure for Camera Recorder ApplicationPrecaution PositionsOperating Procedure for ENG/EFP Application ENG ApplicationR M a L SETAWC White AWCHold Awca Check White BAL AWCClose-up macro shooting Operating Procedure for Studio Application ‘AWCAutomatic Iris Adjustment Lens FLANGE-BACK AdjustmentIris Gain Control in a Lens Automatic White Balance Setting Setting the White BalanceAutomatic Black Balance Setting Black BalanceFilter Selection Wheel Settings Peculiar Phenomena of the CCDHow to display the Main Menu User Setting ProcedureHow to display the Sub-Menu User Setting Centre MARK, ON/OFF HL CHROMA, OFF/LOW/HICAM SET-UP, LOW/MID/HI EVF OUT, Y, NAMCharacter Display Reset of the setting dataHow to Reset Display PositionsAuto Function Display Audio Level DisplayAWC Memory/Auto Function Display Automatic Blaik Balance Control ABCShutter Speed Display Switch Display/Back-up Battery State DisplayClean DNR Display High-light Chroma DisplayLens Iris Selection Display Camera Power and Anton Bauer Intelligent Digital BatteryLens Aperture Display Low Light DisplayDATE/TIME Display ID SettingCamera Status Display ENC SpecificationsPreset ELCMain Optional Accessories System AccessoriesOther Optional Accessories