Panasonic AW-F575E manual Incom Earphone

CAMERA ADAPTOR AW-AD700BSE

Y/C/B: The chrominance (C) and luminance (Y) sig- nals are supplied from the R, G and B Output Connectors for S-VHS format VTR.

R/G/B: The R. G and B stgnals are supplled from the R. G and B Output Connectors.

Y/PB/PR: The colour difference (R-Y & B-Y) signals and luminance (Y) signal are supplied from the VTR/RCU Connector (79) and the R, G and B Output Connectors on the Remote Control Unit for MII and Betacam format VTRs

70. VTR Compatibility Switch (+1/+2/-1)

Set this switch according to the VTR which is connect- ed to the camera.

+1: For 1/2" VHS VTRs

+2: For 3/4” U-vision VTRs, connected to the camera uslng a 14-pin connector, S-VHS VTRs and MII portable VTRs

-1: If a VTR of other manufacture is used, and if this VTR pauses when the tape should be running and viceversa, this switch should be set to this posi- tion

Notes:

1The switch has been preset to the +1 posltlon at the factory

2 Some VTRs may not operare properly when con- nected to this camera, even though the setting of this switch is changed. Please consult your dealer for further mformation

75. Gen-lock Input Connector (ENC) (GEN-LOCK)

The colour video signal of the camera is automatically synchronized to the gen-lock signal (composite or black burst) whtch is supplied to this connector. The gen-lock signal is used for system reference, such as when using a Special Effects Generator

Caution: If the gen-lock signal is jittery (such as when obtained from VTR playback), the camera may not be able to synchronlze properly.

76. Multiplex Signal Input Connector (MPX) Communications between the camera side and the Remote Control Unit (RCU) are available through a Single coaxial cable by using this Connector as the composite signal, gen-lock signal, control signal and Intercom/audlo signal are multiplexed, and the com- posite signal is output from the Remote Control Unit. (RCU)

62.Camera Handle

63.Camera Adaptor Holding Screw/Knob

The camera adaptor can be removed from the camera after loosening two knobs on top of the adaptor and then pressing the release button underneath of the camera while pulling on rear of camera adaptor

64.VTR Start/Stop Button (VTR) (parallel operation)

This button is used to change the recorder mode from pause (Recording Pause) to recording and functlons in the same way as the VTR Start/Stop Button on the lens. Press once to start recording. While recording, the Tally Indicator in the viewfinder Iights and the Tally Light on the vlewfinder also lights

When the button is pressed once more, the recorder is set to the Pause mode (Recording Pause), and the Recording/Tally Indicator and Tally Light will go off

65. Intercom/Earphone Level Control

(INCOM EARPHONE)

Use thls control to freely adlust the volume level in the earphone connected to the Earphone Jack (68) or the headset connected to the Intercom Jack (67)

66. S-Video Output Connector (S-VIDEO OUT)

The lumlnance (Y) and chroma (C) signals for S-VHS VTR or monitor are provided at this connector

67. Intercom Jack (M6) (INCOM)

This jack is used for communication between the cam- era operator and operators of the Remote Control Unit (RCU) and Special Effect Generator in the system.

68.Earphone Jack (M3) (EARPHONE)

When an earphone is connected, the sound picked up by the microphone or the played back audio from a

3/4" U-VISION recorder, connected to the camera through the VTR 14-pin, camera connector, can be monitored Selection of the audio source is enabled by the Earphone Out Selection Switch (71)

69. RCU/VTR Signal Selection Switch (RCU/VTR SIGNAL ENC, Y/C/B, R/G/B. Y/PR/PB)

This switch selects the video Output signal supplied at the VTR/RCU Connector (79) on the adaptor and the Red, Green and Blue Output Connectors on the Remote Control Unit (RCU). The switch has been set to the R/G/B position at the factory

ENC: The composite Output signal for the VTR, such as 1/2 VHS or 3/4" U- Matilc, is supplied

- 14 -

71.Earphone Out Selection Switch (INT/PB)

This switch selects the audio signal from the Earphone Jack (68) to be monitored.

INT: The sound plcked up by the microphone can be monitored.

PB: The played back audio can be monitored

Note: The camera has been preset to the INT position at the factory

72.Audio Level Selection Switch

(AUDI0 LEVEL -20/-60 dB)

Two audio output levels lo the VTR can be selected: -20 dB or -60 dB

The camera has been preset to -20 dB at the factory When using this adaptor with WVRC700A, set this switch to the -20 dB position

74.Video Output Connector (BNC) (VIDEO OUT)

A composite video signal is provided at this connec- tor

78.Circuit Protector (BREAKER)

When excessive current flows into the camera due to some fault, the red button of this cIrcuit protector pro- trudes to cut off the circult power

After solving the problem, press the red button again to reset the circuit protector.

Caution: Refer serving to qualifled serwce person- nel to solve the problem.

79.VTR/RCU Connector (26pin) (VTR/RCU)

When using the camera together with a Panasonic portable colour VTR, the specified VTR Cable should be connected between the camera and VTR. This connector is also used for connection with the 26-pin studio cable from the Remote Control Unit (RCU) for comprehensive system operation. When connecting the 26-pin studio cable to this connector, the camera is automatlcally set to the Remote Control Unit (RCU) operatlon mode

??3/4" U-vlsion portable VTR (14-pin) WVCA26A14 (26P-14P cable)

MII portable VTR (26-pin) WV-CA26A26 (26P-26P cable)

- 15 -