Panasonic AW-F575E manual Shutter Speed Display, High-light Chroma Display, Noise Suppress Display

3. Shutter Speed Display

0ne of the following displays appears for one second when the position of the Electronic Shutter On/Off Switch (ll) is changed

Display	Shutter/High Gain	Description
	Indicator (LED)
SHUTTER OFF	OFF	The Electronic Shutter On/Off Swtich is set to OFF. Normal camera operation.
SHUTTER 1/120	ON	Camera is set to electronic shutter mode with shutter speed of 1/120 seconds.
SHUTTER 1/1250	ON	Camera is set to electronic shutter mode with shutter speed of 1/250 seconds
SHUTTER 1/500	ON	Camera is set to electronic shutter mode wih shutter speed of 1/500 seconds
SHUTTER 1/1000	ON	Camera is set to electronic shutter mode wih shutter speed of 1/1000 seconds

6. High-light Chroma Display

The high-light chroma state is displayed for one sec- ond when the High Light Chroma Switch is pressed. Note: When the Remote Control Unit is used, the OFF, LOW or HIGH can be selected on the menu.

Display	Position of High Light Chroma Switch
HL CHROMA	OFF
	HL CHROMA ON (LOW position had been set in the No 2
	HL CHROMA ON (HIGH position had been set in the No 2

The above displays are indicated by pressing the Check Button (25)

9. Accumulative Recording Time Display

White the Check Button (25) is pressed, the accumula- tive recording time is displayed during ENG/EFP oper- ation.

When a camera/recorder system utllizes an AU-45H, the tape counter is displayed instead of accumulative recording time.

Notes:

1 The display value is reset to 0 HOUR 00 MIN 00 SEC (O:OO:OO) by either the Recording Time Reset Button (21) on the camera or the Reset button on the VTR

2.The maximum recording time that can be dis- played is 7 HOURS 59 MIN 59 SEC (7:59:59). If the recording time should exceed this value, the display will start counting again from 0:00:00

SHUTTER 1/2000	ON	Camera is set to electronic shutter mode with shutter speed of 1/2000 seconds
SHUTTER 1/4000	ON	Camera is set to electronic shutter mode wih shutter speed of 1/4000 seconds
SHUTTER 1/10000	ON	Camera is set to electronic Shutter mode with shutter speed of 1/10000 seconds
SYNCHRO SCAN	ON	Camera is set to the Synchro Scan mode
ELC	ON	The Electronic Light Control is being activated

7. Noise Suppress Display

The I Noise Suppress state is displayed for one sec- ond when the item Noise Suppress Switch is pressed in the menu off mode

Note: These selections can be made by the menu

Display Positlon of Item / Noise Suppress Switch

1 NOISE SUP

OFF OFF

10. Switch Display/Back-up Battery State Display

When the back-up battery for white balance and black balance memories, as well as the character display, has a low charge ‘BACK UP NG’ is displayed Replace the back-up battery immediately

When pressing the switches on the front or side of the camera, the switch “ame pressed ca” be dlsplayed in the vlewflnder as shown below

Notes:

1Refer replacement of the back-up battery to quali- fied service personnel

2.The back-up battery will supply power for approx- imately 10 years

4. Detail Correction State

The detail/aperture correctilon state is displayed for one second when the setting of the Detail Level Selection Switch (20) is changed

Note: The detail/aperture correction state is also dis- played when the Check Button (25) is pressed.

5. Clean DNR Display

The clean DNR state is displayed for one second when the position of the Clean DNA Selection Switch (17)

Display	Position of the Detail Level Selection Switch
	(20)
DETAIL OFF	OFF

DETAIL LOW LOW

DETAIL HIGH

HIGH

The above displays are Indicated by previewing the Check Button (25)

Display	Position of the Clean DNR Selection Switch
CLEAN DNR	OFF
CLEAN DNR	LOW
LOW
CLEAN DNR	HIGH
HIGH

Note: The above displays are indicated by pressing the Check Button (25)

6. Scene File Display

The scene file setting is changed or Check Button (25) is pressed, the followig display appears for one sec- ond

SCENE 1 STUDIO: Scene File Selection Switch had been set to SCENE 1

SCENE 2 ENG: Scene File Selection Switch had been set to SCENE 2 and LIGHTING in No 1 Main Menu is set to HALOGEN

SCENE 3 OUTDOOR: Scene File Selection Switch had been set to SCENE 2 and LIGHTING in No 1 Main Menu is set to FLUORESCENT

SCENE USER A: Scene file condition is under the User A state

SCENE USER B: Scene file condition is under the user B state

Display	Description
GAIN	High Gain Selection Switch (29) is pressed.
WHITE BAL	Whlte Balance Selection Switch (28) is
	pressed.
BAR/N EYE/	Colour Bar/Night Eye/Camera Selection
CAMERA	Switch (27) is pressed.
AUTO W/B	Auto White/Auto Black Set Swich (6) is
	pressed
LENS IRIS	Lens lits Selection Switch (7) is pressed
NONE	Back-up can not be operated
BACK-UP	Back-up can not be operated
NG

- 70 -

- 71 -