Panasonic AW-F575E manual 14X Servo Control Zoom Lens AW-LZ14ST73

Page 7

??26 pin Studio Cable (RCU Cable) WV-CA26U15

WV-CA26U30 WV-CA26U100

recorded. The Tally indicator also lights when the camera is in full system operation together with the Remote Control Unit and Special Effects Generator in case a tape is not loaded or the tape end is reached, or if the servo mechanism is working improperly, this indicator will start blinking to warn the operator of such

86. Lens Cable with 12-pin Connector

After having set the recorder to the recording standby

This cable supplies power to the servo control zoom

mode, press this button to start and pause recording.

motor and the automatlc iris control device.

While recording is in progress, the Recording/Tally

The cable

should be connected to the Lens Connector

indicator in the viewfinder and the Tally Light (101) on

(1) on the

camera.

front of the viewfinder lights.

80. Lens Connector

This connector is used to connect the lens cable for zoom, focus or servo control.

81. Control connector

This connector is used to connect the optional Pan/Tilt Control Cable WV-CA10U25

92.Battery Connector (BATTERY)

Connect the cord from the Battery Pack to this con- nector

93. Recording/Tally Indicator (red) (REC TALLY)

This indicator Iights when the VTR is set to the record- ing mode (through the VTR Start/Stop Button) and informs the person concerned of scenes being

faults.

Note: lf a portable VTR is not connected to the cam- era, the Recording/Tally indicator will not light.

84. Battery Pack Mounting Angle

Mount the AC Adaptor/Charger WV-PS34 or Power Separator WV-PS700 on the camera by sliding it down along this mounting angle

85. 66-pin Multi Connector

When mounting this adaptor engage the 66-pin con- nectors on the camera and this connector

87. Auto Iris Button (IRIS)

When this button is pressed while the lris Control Selection Switch (86) is set to the M (manual) position the Iens iris is automatlcally set according to the light intensity reaching the lens

Note: Button must be pressed for 5 seconds or improper iris setting will result

88. Iris Control Selection Switch (A/M)

This switch selects the operational condition of the lens iris:

A (Auto): The lens iris is automatically controlled. When the camera is used in studto applications together with the Remote Control Unit (RCU), this switch should be set to the ‘A’ position. In this case, the lens iris is remotely controlled from the RCU or RCB

M (Manual): The lens iris can be manually controlled by rotatlng the lris Rlng (97). With this setting, the correct lens iris setting can also be set by press- ing the Auto Iris Button (87).

93.Servo/Manual ZOom Selection Switch (SERVO/MANU)

This swltch is used to select between zooming by servo control or manually

SERVO: Zoom operation is performed by pressing either side of the Servo Zoom Control (89)

MANU: Zoom operation is performed manually by rotating the Zoom Ring/Lever (96)

94. Connector for Zoom Remote Controller

The Zoom Remote Controller included in the Lens Control Kit WV-LK35 should be connected to thls con- nector. This will allow remote control of zooming

95. Focus Ring

Rotating this ring willI

change the lens

f o c u s . By

observing the picture

in the vliwfinder,

correct focus

can easily be set.

 

 

With the optlonal Lens Control Kit WV-LK35, including flexible cable for the Zoom Remote Controller and Focus Controller, zooming a n d focusing c a n b e remotely controlled.

14X SERVO CONTROL ZOOM LENS AW-LZ14ST73

94-

-16 -

89. Servo Zoom Control (Wide/Tele)

The zoom function of this 1.4f zoom lens can be con- trolled by pressing this control. Zooming to tele as well as wide angle is possible. Furthermore, the zoom- ing speed can be controlled by changing the pressure applied on this control.

90. Return Video Button

When an auxlllary signal such as a Ilneview signal from a Special Effects Generator is supplied to the auxiliary connector of the Remote Control Unit (RCU) while the camera is set up for system operatlon, this signal can be previewed on the electronic viewfinder as long as this button is kept pressed. When a 3/4" U- vision portable recorder, connected through the VTR s 14-pin camera input connector, or an S-VHS VTR recorder is set to the playback mode, the played back picture can be viewed as long as this button is kept pressed

91. Auto Iris Sensitivity Control (IRIS GAIN)

With setting the iris Control Selection Swltch (88) to the A position, adjust the iris Galn by turnlng this con- trol.

92. VTR Start/Stop Button (VTR)

This switch is used to start and pause the connected recorder . The function of thls button is identlcal to the VTR Start/Stop Button (5) on the camera

-17 -

96. Zoom Ring/Lever

By seyying the Servo/Manual Zoom Selection Switch

(93)to the MANU (manual) position, zooming can be manually performed through use of this rlng/lever. 13 times magniflcation is posslble f r o m wide angle to telephoto. When the Servo/Manual Zoom Selection Switch (93) is set to the SERVO position, zooming is performed with the Servo Zoom Control (69)

97.Iris Ring

When the iris Control Selection Switch (66) is set to the

M(manual) positlon, the lens iris can be manually adjusted by rotating this ring.

98.Flange-back Lock Knob

The Flange-back Adjustment Ring (99) can be locked by turning this knob.

99. Flange-back Adjustment Ring

The flange-back (or back focus) of the lens can be adfusted by rotating this ring. The Flange-back Lock Knob (98) should be released prior to adjustment

100. Macro Ring/Button

For close-up shooting, rotate this ring to the macro area while pressing this b u t t o n . After setting lhe Servo Zoom Control (69) to the WIDE position, close- up shooting up to approximately 50 mm (2”) from the lens surface is posslble by rotating this ring

Image 7
Contents AW-F575E Auto Iris Serfvo Control Zoom Lens Lens Iris Selection SwitchMajor Operating Controls and Their Functions Camera Head AW-F575HEDTL, LEVEL-HIGH/LOW/OFF Scene FILE, User A/B/1/2/3Back Light Comp ON/OFF ON/OFFBAR/N.E/CAMERA Camera Adaptor AW-ADS00AEAUTO/ATW ATW/A/B Earphone OUT SEL, INT/PB Signal SelectIncom Earphone 14X Servo Control Zoom Lens AW-LZ14ST73 Electronic Viewfinder WV-VF42 Remote Control Unit WV-RC7OOAAWC/HOLD/ABC RCBOUTPUT-VIDEO 1, Video Remote Control Unit Rack Mount Frame WV-Q70Cable SELECT, MULTI/MPX Night EYE, HIGH/LOW/OFF Remote Control Unit WV-RC550AUTO/ATW, ATW/A/B Item Switch Item Electronic Shutter Selection SwitchDown Switch Down Up Switch UPLens Control KIT WV-LK35 Electronic Viewfinder WV-VF65BCarrying Case WV-CC500A Lens Control KIT WV-LK36 Tripod Mounting Adaptor WV-QT700Mounting the Camera Adaptor InstallationXLR type Microphone Connector Microphone Information Installatìon of the Optional Mìcrophone HolderMounting the 5 Electronic Viewfinder Mounting the 1.5 Electronic ViewfinderMounting of the Betacam Format VTR Installation of the AC Adaptor/Charger WV-PS34Mounting on the Tripod Mounting Adaptor Removing the VTR from the CameraAttaching the Shoulder Strap Connection with a sub-VTR back-up VTR Connection with the Remote Control BoxSystem Connection Connection with the VTROUT PC Mode SystemPositions Operating Procedure for Camera Recorder ApplicationPrecaution VTRENG Application Operating Procedure for ENG/EFP ApplicationWhite AWC SETAWC R M a LHold Awca Check White BAL AWCClose-up macro shooting ‘AWC Operating Procedure for Studio ApplicationAutomatic Iris Adjustment Lens FLANGE-BACK AdjustmentIris Gain Control in a Lens Black Balance Setting the White BalanceAutomatic Black Balance Setting Automatic White Balance SettingPeculiar Phenomena of the CCD Filter Selection Wheel SettingsHow to display the Main Menu User Setting ProcedureHow to display the Sub-Menu User Setting EVF OUT, Y, NAM HL CHROMA, OFF/LOW/HICAM SET-UP, LOW/MID/HI Centre MARK, ON/OFFDisplay Positions Reset of the setting dataHow to Reset Character DisplayAutomatic Blaik Balance Control ABC Audio Level DisplayAWC Memory/Auto Function Display Auto Function DisplayHigh-light Chroma Display Switch Display/Back-up Battery State DisplayClean DNR Display Shutter Speed DisplayLow Light Display Camera Power and Anton Bauer Intelligent Digital BatteryLens Aperture Display Lens Iris Selection DisplayDATE/TIME Display ID SettingCamera Status Display ELC SpecificationsPreset ENCMain Optional Accessories System AccessoriesOther Optional Accessories