Panasonic AW-F575E manual Operating Procedure for Camera Recorder Application, Vtr, Precaution

F. VP Multìplex SyStem

CONTROL

Precaution

In gen-lock operatlon in a video power (VP) multiplex system with a single coaxial cable, the camera may become out of syn- chronizatlon depending on the waveform distortion of the burst signal that serves as a gen-lock signal

-Connect the Multiplex Output Cable on the WV-PS700 lo the Multipiex Slgnal Connector on the AW-AD700BSE.

-Connect the Power Cable on the optional Power Separator WV-PS700 to the External DC Input Connector on the AW- AD700BSE

-Connect the coaxial cable between the Multiplex Input Connector on the Power Separator WV-PS700 and the Multiplex Connector on the RCU

-To control the Zoom or focus function of lens, connect the Control Cable on the lens having the Focus or Zoom function to the Lens Connector on AW-AD700BSE.

And then connect the multicable between the WV-RC700A and lens control unit

Notes:

1 The optional Power Separator WV-PS700 and the Camera Adaptor AW-AD700BSE are required to supply the power to the

	camera from this unit
2	The optional studlo cable (26-pin) cannot be used in the VP multiplex system simultaneously slmuitaneously
3	In this system, R/G/B. Y/C, Y/PR/PB	and Aux cannot be supplied.
4	Be sure to set the Cable Selection	Swltch on the Camera Adaptor AW-AD700BSE to the MPX position and the Cable
	Selection Switch on the RCU to the VP positlon.
5.	After turning on the power of this unit and camera head, it takes approxlmately 8 seconds to control the camera

6When the Camera Adaptor AW-AD700BSE is used in the above system, the following items are not available a. Bidirectional Inter Communication

b. Audio Output

c. Zoom, or Focus Control d. Pan/Tilt Control

7Pan/Tilt Control SIgnaI Input to the Control Connector on the RCU is output from Control Connector on AW-AD700BSE.

8.For the Audio function, set the Switch 2 on the MOD board Inside this unit as shown below

- 44 -

OPERATING PROCEDURE FOR CAMERA RECORDER APPLICATION

1. Turn on the Power Switches on the camera and VTR. DC POWER

				Operating mode of	Operating mode of
	Power Switch		Power Indlcator	Dockable VTR/	Portable VTR	Dperatlng mode of Sub-VTR
				camera	(SAVE is bullt-in)
VTR		CAM				Power	Operating
							condltlon
	OFF		lights off	Power off

VTR:	The tape	l
The tape loadlng
SAVE

				The recording
		The power af VTR
				mode is controlled
ON	lights red	and camera are	power on
				by the VTR Start/
		turned on
				stop Button.

Notes:

1When the power of the camera is turned off from on, the sub-VTR is put in the recording stop mode from the recording start/stop mode

Then the recording Start/Stop is controlled the operating switch on the VTR

When the power of the camera is turned on from off, the recordlng is stopped by setting the operating switch on the VTR to the recording start mode

Then the recording start/stop mode is controlled by the VTR Start/Stop Button on the camera.

2When pressing the VTR Start/Stop Button after setting the Dockable VTR to ON ---> SAVE --> ON, the recordlng start/stop mode is reversed.

3When turnlng off the power of the AU-45H in the camera recorder system. the power off control from the camera side is not avallable.

2. Insert a cassette in the VTR

3. Set the switches on the camera as follows:

Switches Positions

Note: Set these switches to the most suitable position according to shooting condltions

- 45 -