Panasonic BM-ET330 operating instructions Connection terminal

Page 14

Connection terminal

@1

Pin No.

q w e r t y u i o

!0

qWiegand power (card reader) Supplies power to a card reader.

wWiegand GND (card reader)

This is the ground terminal for the power supply and communication between the iris reader and a card reader.

eWiegand DATA0 (card reader)

A signal (DATA0) is input from a card reader to this ter- minal.

rWiegand DATA1 (card reader)

A signal (DATA1) is input from a card reader to this ter- minal.

tWiegand ACCEPT-LED (access control panel)

A signal (Wiegand ACCEPT-LED) is input to control the ACCEPT indicator of this iris reader when Wiegand out- put is set up.

yWiegand power (access control panel)

The iris reader works even when nothing is connected to this terminal.

uWiegand GND (access control panel)

This is the ground terminal for communication between the iris reader and an access control panel.

iWiegand DATA0 (access control panel)

A signal (DATA0) is output from this terminal to an access control panel.

oWiegand DATA1 (access control panel)

A signal (DATA1) is output from this terminal to an access control panel.

!0Wiegand REJECT-LED (access control panel)

A signal (Wiegand REJECT-LED) is input to control the REJECT indicator of this iris reader when Wiegand out- put is set up.

!1RS-485 (A) (access control panel)

A signal (RS-485 (A)) is input from or output to an access control panel.

!1

!2

!3

!4

!5

!6

!7

!8

!9

@0

!2RS-485 (B) (access control panel)

A signal (RS-485 (B)) is input from or output to an access control panel.

!3RS-485 (A) (card reader)

A signal (RS-485 (A)) is input from or output to a card reader.

!4RS-485 (B) (card reader)

A signal (RS-485 (B)) is input from or output to a card reader.

!5Alarm input1 (recognition start/buzzer)

An alarm signal is input to this terminal to start recogni- tion or activate buzzer sound.

!6Recognition result output1 (ACCEPT)

This terminal is activated when recognition is success- fully completed.

!7Recognition result output2 (REJECT)

This terminal is activated when recognition is not suc- cessfully completed.

!8Alarm output1 (power status)

This terminal is closed and low when power is supplied from an external power-supply device to the iris reader. The terminal is opened when the power supply is shut down.

!9Alarm output2 (tamper detection)

This terminal is activated when the iris reader enters the "tamper detection" mode by the front/rear tamper detec- tion switch (activated until the "tamper detection" mode is cancelled).

@0GND

This is the common terminal for the alarm output con- nectors.

@1Power input terminals

12 V DC (+12 V at the left/GND at the right) or 24 V AC

14

Image 14
Contents Operating Instructions English Version Important Safety Instructions Limitation of Liability Trademarks and Registered TrademarksContents Preface As a recognition iris reader for iris recognitionSupporting a common access control interface FeaturesAccess control system can be composed Built-in video surveillance cameraTo avoid fire or personal injury PrecautionsGeneral Safety Requirement Settings of this appliance are configured by the iris server Document Convention Notification about this Document External View Front ViewInternal View Rear tamper detection switchRear View Mounting hook holeConnection terminal Specifications of RS-485 Connectors for Card Reader Specifications of Alarm Output Connectors AcceptInstallation and Connections Description about the Connection ExamplePreparing the Necessary Items Notification about the Installation SitePreparation Cable PreparationCheck the Capturing Range Installation Space and Recognition RangeKeep the Installation Space Installation WallAttach the LAN cable to the LAN connector Instructions for Proper Enrollment and Recognition If you are wearing contact lensesYes How to Position Your Eyes in the MirrorStand where you can see the iris reader from the front side Hold the tilt handles at the sides of the front panel Make sure that you can see both eyes in the mirrorIf You are Wearing an Eyepatch, etc Cases of Enrollment/Recognition FailureIf you are wearing glasses/sunglasses, take them off How to Carry out EnrollmentStand Sit down in front of the iris reader Start iris image capturingResult is output Move your face so as your eyes are positioned within 50 cm How to Carry out RecognitionRecognition by an Iris Reader only 64 ft. from the iris readerDuring capturing, open your eyes widely Voice guidance Recognition by an Iris Reader and a Card ReaderPass a card through the card reader Rejectaccept Troubleshooting When Enrollment/Recognition Becomes InvalidBefore Requesting for Repair Cases of Enrollment/Recognition FailureProblem Check item Remedy Input/Output SpecificationsGeneral FunctionStandard Accessories Osaka, Japan

BM-ET330 specifications

The Panasonic BM-ET330 is a state-of-the-art electronic message board designed to meet the modern demands of communication in various professional environments. This device seamlessly combines functionality and advanced technology, making it an ideal solution for businesses, educational institutions, and public spaces.

One of the standout features of the BM-ET330 is its high-resolution display. The screen ensures that messages are clear and easy to read from a distance, making it perfect for capturing attention in busy areas. With vibrant colors and sharp text, users can convey information effectively and attractively.

The BM-ET330 employs cutting-edge LED technology, allowing for significant energy savings compared to traditional displays. This environmentally friendly design not only lowers operational costs but also reduces the device's carbon footprint. The long lifespan of LED components further enhances its value, as users can expect years of reliable service without the need for frequent replacements.

Another notable aspect of the BM-ET330 is its user-friendly interface. The device supports intuitive navigation, allowing users to create, edit, and manage messages effortlessly. Whether it's a promotional announcement, schedule information, or directional signage, the functionality of the BM-ET330 makes it easy to keep communication up to date.

Connectivity is also a key characteristic of the BM-ET330. It offers multiple connection options, including USB, Ethernet, and wireless capabilities. This versatility allows users to upload content and updates from various devices, ensuring that information can be shared quickly and efficiently.

Moreover, the BM-ET330 includes robust scheduling features. Users can automate messages to display at specific times or dates, making it a highly efficient tool for ongoing communication needs. This can be especially beneficial for businesses looking to promote special offers, announce events, or provide timely information to customers and employees alike.

In conclusion, the Panasonic BM-ET330 is a remarkable electronic message board that stands out due to its high-quality display, energy-efficient LED technology, user-friendly interface, and versatile connectivity options. Its scheduling features further enhance its applicability for a variety of communication needs, making it an excellent investment for anyone looking to modernize their messaging system.