Panasonic WV-CW964 2POSI, PATROL2, 3POSI, PATROL3, 4POSI, PATROL4, Alarm, AUX1, AUX2

Page 41

3.Move the cursor to ALARM IN 2, and then tilt the joystick left and right to select the operation the camera should perform when an external signal is

received by ALARM IN 2.

OFF

: Ignore alarm input signals.

2POSI

: Move to preset position 2.

SEQ

: Start sequential movement.

PATROL2

: Start PATROL 2.

PATROL2 (S) : Start PATROL 2, and maintain the stored picture quality settings (page 35) even after completion.

AUTOTRACK2 : Move to preset position number 2, and then perform auto tracking.

4.Move the cursor to ALARM IN 3, and then tilt the joystick left and right to select the operation the camera should perform when an external signal is

received by ALARM IN 3.

OFF

: Ignore alarm input signals.

3POSI

: Move to preset position 3.

SORT

: Start sort movement.

PATROL3

: Start PATROL 3.

PATROL3 (S) : Start PATROL 3, and maintain the stored picture quality settings (page 35) even after completion.

AUTOTRACK3 : Move to preset position number 3, and then perform auto tracking.

5.Move the cursor to ALARM IN 4, and then tilt the joystick left and right to select the operation the camera should perform when an external signal is received by ALARM IN 4.

OFF

: Ignore alarm input signals.

4POSI

: Move to preset position 4.

BW

: Black and white display while

 

signal is being input.

PATROL4

: Start PATROL 4.

PATROL4 (S) : Start PATROL 4, and maintain the stored picture quality settings (page 35) even after completion.

AUTOTRACK4 : Move to preset position number 4, and then perform auto tracking.

Notes:

•Use PATROL 1 (S) to 4 (S) if you want to switch picture quality (for example to switch picture quality from day to night) when an alarm input is received. ALARM IN4 can be used combined with BW.

To use the camera with this application, set the picture quality you want to switch before registering the patrol, then start the patrol registration and then end the registration immediately.

•If you want to change the picture quality settings according to alarm input for PATROL 1 (S) to 4 (S), the settings are applied to the camera settings and are kept even after the camera is turned on again.

•PATROL1(S)-4(S) displays only the set number of patrol routines (page 35).

6.Move the cursor to CNT-CLS 1, and then tilt the joystick left and right to select the alarm output that should be performed over ALARM OUT 1 when an alarm is detected.

-41-

OFF

: No alarm output

ALARM

: Output an alarm signal when an

 

alarm is detected by the motion

 

detector (page 39) or the preset

 

alarm (page 40). After selecting this

 

setting, perform step 7 to specify

 

the alarm signal output time.

AUX1

: Output a contact close signal

 

when AUX1 input is received from

 

the system controller.

7.If you selected ALARM in step 6, move the cursor to TIME OUT and then tilt the joystick left and right to select the alarm signal output time.

Tilting the joystick cycles through the output time display in the sequence shown below. (unit: ms)

100 MS ↔ 200 MS ↔ 1000 MS ↔ 2000 MS ↔ 4000 MS

Note: The shorter the duration, the more frequent will be the detection output.

8.Move the cursor to CNT-CLS 2, and then tilt the joystick left and right to select the alarm output that should be performed from ALARM OUT 2 when an alarm is detected.

OFF

: No alarm output

BW

: Output a contact close signal only

 

while the camera is in the black

 

and white mode.

AUX2

: Output a contact close signal

 

when AUX2 input is received from

 

the system controller.

Note: It is recommended to set the connected external device to ignore the shorter alarm outputs of 90 ms or less from the camera.

9.Move the cursor to COAX ALM OUT, and then tilt the joystick left or right to toggle it on and off.

This setting turns alarm controls whether an alarm is output when the camera moves to one of the preset positions specified for ALARM IN 1 through 4 (1POSI,

2POSI, 3POSI, 4POSI) in steps 2 through 5, above.

ON

: Output an alarm signal from the

 

video output connector at the

 

point the camera finishes moving

 

to a preset position (number 1

 

through 4) when there is alarm

 

input to ALARM IN (1 through 4).

OFF

: No alarm signal output

Notes:

•The camera ignores alarm inputs during manual operation.

•Turn off alarm outputs when the system controller downloads or uploads the preset data.

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Operating Instructions English Version Important Safety Instructions Limitation of Liability Disclaimer of WarrantyStandard Accesories FeaturesPrecautions Operating Precautions Combining devices Self-diagnosing FunctionContents Ensuring Trouble-free Operation ConstructionInstallation Precautions About effects on image quality Important hints to help with the installationCommunication Parameters DIP Switch DIP Switch SettingsUnit Number DIP Switch DIP Switch Unit Number RS485 Communication Parameters DIP SwitchAssemble procedure Camera InstallationPrecautions Mounting the CameraMounting the Bracket Attach the brackets to the camera Installing the bracketsAC Power Supply Connection Alarm In/Out RatingsAccessory Connector Information ConnectionsConnect this to 24 V AC Class 2 Power Supply only How to Assemble the Cable with the Accessory ConnectorEnables X ON/X OFF data flow control RS485 SetupUSE AUTO1Displaying the Setup Menu Using the Setup MenuCamera ID Settings When using the WV-CU650Preset Position Settings Scene Select SettingsScene Select Settings Position Setting Position SETPreset ID Setting Preset ID To copy the preset ID of another position number Language SettingAdvanced Menu Settings ALC Camera SettingsUsing the Camera Setup Menu OFF Synchronization Sync Adjusting the Phase for Line-lock SynchronizationWhite Balance White BAL AWC→PUSH SETDigital Noise Reduction DNR Resolution ResolutionBlack and White Mode BW Mode Example Auto Focus AF ModeZoom Limit Zoom Limit Auto Image Stabilizer StabilizerUsing the Pan/Tilt Setup Menu PAN/TILT SettingsPosition Number Selection Preset Light Control ALC/MANUALScene File Setting Scene File Auto Focus AF ModePreset Speed Setting Preset Speed Deleting a Preset Position DELApan HomeSEQ SortPAN Limit Configuring Auto PAN Detailed SettingsAuto PAN Key Setting Auto PAN KEY When Learn is selected Patrol Function Setting PatrolWhen Play is selected Image Hold Setting Image Hold Privacy Zone Setting Privacy ZoneArea Title Setting Area Title Digital Flip Setting Digital FlipProportional Pan/Tilt Setting PROPO. P/T Cleaning Settings Cleaning Tilt Angle Setting Tilt AngleUsing the Alarm Setup Menu Alarm SettingsConfiguring Detailed Motion Detector Settings for Mode ModePATROL1 1POSIAutopan 2POSI AlarmPATROL2 3POSIALL Special SettingsUsing the Special Setup Menu Returning Camera Settings to Their Defaults Adjusting the Preset Positions RefreshCamera Reset To delete a blemish compensation patternUsing the Scene Select Setting Menu Scene Select SettingPassword Lock Settings Password SettingsTurning Password Lock On and Off Changing the PasswordOK Reset RET TOP Shortcuts Controller Operation SettingIris Close FIX TroubleshootingProblem 40-41 39-40 Periodically check the power cord General SpecificationsPan and Tilt LensMain Functions Page Panasonic System Solutions Company
Top Page Image Contents