Panasonic WV-CW964 Connections, Alarm In/Out Ratings, OFF Open, AC Power Supply Connection

Page 19

CONNECTIONS

Precautions

•The following connections should be made by qualified service personnel or system installers in accordance with all local codes.

•Turn off the power at the fuse box before starting the installation work, or it so could result in fire, electric shock, personal injury, and material damage.

 

24 V AC Cable for Heater

 

Separate 2-wire

 

 

 

24 V AC Cable for camera

 

24 V AC

 

 

RS485 Data Port

Twisted Pair Cable*1

To Matrix Switcher,

(RJ-12)

etc.

Video Output

Coaxial Cable (5C-2V)*2

 

Connector

To VIDEO IN port

 

 

(BNC)

(CAMERA IN)

Alarm Input

 

 

Connector

8P Alarm Cable (provided)

 

 

 

To sensor, etc.

Alarm Output

4P Alarm Cable (provided)

 

Connector

 

 

To buzzer,

display device, etc.

*1: For twisted pair cable, use shielded low-impedance cable with a thickness of at least AWG#22 (0.33 mm2).

*2: Keep the overall length of coaxial cable under 1200 meters (in the case of 5C-2V).

*3: Be sure to connect the grounding cable to ground.

RS485 Data Port

Data

Red

Orange

Tx

Yellow

Data

Green

Rx

 

(RJ-12)

T(B)

T(A)

R(B)

R(A)

Alarm Input Connector

Alarm In 1 (Black)

GND (Brown)

Alarm In 2 (Red)

GND (Orange)

Alarm In 3 (Yellow)

GND (Light Blue or Green)

Alarm In 4 (Blue)

GND (Violet)

Alarm Output Connector

Alarm Out 1 (Grey)

GND (White)

Alarm Out 2 (Pink)

GND (Light Green

or Light Blue)

Alarm In/Out Ratings

Alarm In : 5 V DC pull-up input. Drive capacity of at lease 0.2 mA required.

OFF : 4 V DC minimum 5 V DC maximum, or open

ON : 1 V DC maximum or short

Alarm Out : Open collector output. 16 V DC, 100 mA maximum drive capacity

OFF : Open

ON : 100 mA maximum

*When connecting to an external device, set up the system so the ratings are not exceeded.

Note: Do not turn off camera power within 30 seconds after turning it on. Doing so can cause pan, tilt, zoom, or focus to go out of position.

• 24 V AC Power Supply Connection

Recommended wire gauge sizes for 24 V AC line

Copper wire size

#24

#22

#20

#18

(AWG)

 

(0.22mm2)

(0.33mm2)

(0.52mm2)

(0.83mm2)

 

 

 

 

 

 

Length

(m)

20

30

45

75

of cable

 

 

 

 

 

(ft)

65

100

160

260

(approx.)

 

 

 

 

 

 

Accessory Connector Information

Pin no.

Power source

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

24 V AC LIVE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

24 V AC NEUTRAL

 

4

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

Ground

 

2

 

1

4

Not use

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-19-

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Operating Instructions English Version Important Safety Instructions Limitation of Liability Disclaimer of WarrantyStandard Accesories FeaturesPrecautions Operating Precautions Combining devices Self-diagnosing FunctionContents Ensuring Trouble-free Operation ConstructionInstallation Precautions About effects on image quality Important hints to help with the installationCommunication Parameters DIP Switch DIP Switch SettingsUnit Number DIP Switch DIP Switch Unit Number RS485 Communication Parameters DIP SwitchMounting the Camera Camera InstallationAssemble procedure PrecautionsMounting the Bracket Attach the brackets to the camera Installing the bracketsConnections Alarm In/Out RatingsAC Power Supply Connection Accessory Connector InformationConnect this to 24 V AC Class 2 Power Supply only How to Assemble the Cable with the Accessory ConnectorAUTO1 RS485 SetupEnables X ON/X OFF data flow control USEWhen using the WV-CU650 Using the Setup MenuDisplaying the Setup Menu Camera ID SettingsPosition Setting Position SET Scene Select SettingsPreset Position Settings Scene Select SettingsPreset ID Setting Preset ID Advanced Menu Settings Language SettingTo copy the preset ID of another position number Using the Camera Setup Menu Camera SettingsALC OFF AWC→PUSH SET Adjusting the Phase for Line-lock SynchronizationSynchronization Sync White Balance White BALBlack and White Mode BW Mode Resolution ResolutionDigital Noise Reduction DNR Auto Image Stabilizer Stabilizer Auto Focus AF ModeExample Zoom Limit Zoom LimitLight Control ALC/MANUAL PAN/TILT SettingsUsing the Pan/Tilt Setup Menu Position Number Selection PresetDeleting a Preset Position DEL Auto Focus AF ModeScene File Setting Scene File Preset Speed Setting Preset SpeedSort HomeApan SEQAuto PAN Key Setting Auto PAN KEY Configuring Auto PAN Detailed SettingsPAN Limit When Play is selected Patrol Function Setting PatrolWhen Learn is selected Image Hold Setting Image Hold Privacy Zone Setting Privacy ZoneProportional Pan/Tilt Setting PROPO. P/T Digital Flip Setting Digital FlipArea Title Setting Area Title Cleaning Settings Cleaning Tilt Angle Setting Tilt AngleMode Alarm SettingsUsing the Alarm Setup Menu Configuring Detailed Motion Detector Settings for ModeAutopan 1POSIPATROL1 3POSI Alarm2POSI PATROL2Using the Special Setup Menu Special SettingsALL To delete a blemish compensation pattern Adjusting the Preset Positions RefreshReturning Camera Settings to Their Defaults Camera ResetUsing the Scene Select Setting Menu Scene Select SettingChanging the Password Password SettingsPassword Lock Settings Turning Password Lock On and OffOK Reset RET TOP Shortcuts Controller Operation SettingIris Close FIX TroubleshootingProblem 40-41 39-40 Periodically check the power cord Lens SpecificationsGeneral Pan and TiltMain Functions Page Panasonic System Solutions Company
Top Page Image Contents