6.Move the cursor to DWELL TIME, and then tilt the joystick left or right to select an alarm detect dwell time setting.
After alarm detection, the next alarm is not detected until the specified dwell time elapses.
Tilting the joystick cycles through the setting display in the sequence shown below. (unit: sec)
2S ↔ 5S ↔ 10S ↔ 30S
7.Move the cursor to RECOVER TIME, and then tilt the joystick left or right to select an alarm reset time setting.
Tilting the joystick cycles through the setting display in the sequence shown below. (unit: sec, min)
If you set OFF, then it does not reset until some other operation is done. If AUTO TRACK is set, the camera starts automatic tracking when change (movement) is detected in the image during SEQ or SORT.
OFF ↔ 1MIN ↔ 2MIN ↔ 3MIN ↔ 5MIN ↔ 10MIN
AUTO TRACK ↔ 60MIN ↔ 30MIN ↔ 20MIN 
Notes:
•Monitoring is usually done in SEQ mode, and when the camera detects change (movement) automatic tracking starts. To have the camera return to SEQ mode after a certain amount of time, set the SELF RETURN setting to SEQ.
•Use the mask setting to mask areas where there is wind movement of curtains, etc.
•Use a lower sensitivity level (LEVEL) setting for areas where illumination is low and prone to digital noise. Also note that operation error can occur when the illuminance of a subject is changed suddenly by the headlights of passing cars, turning lights on or off, etc.
•There is a delay of about 0.2 second from the point that the camera detects change (movement) in the image and the point that a signal is sent to the alarm terminal of a VCR, etc.
•Alarms are not output while the setting menu is displayed, unless demo mode alarm output is turned on.
•Alarms are not output when PAN, TILT, ZOOM, FOCUS or other functions are operating.
•When the motion detector is set to MODE 1 or MODE 2, it outputs alarm data during the blanking period. This can cause operational problems for a VCR or other device that uses a time code signal, etc. Turn off the motion detector when not using coaxial communication.
•The motion detector is not intended for use as specialty device for the prevention of theft, fire, etc. The manufacturer assumes no responsibility for any accidents that occur or any losses incurred while this product is being used.
(2)Preset Alarm Setting (PRESET ALM)
Turning on the preset alarm will output an alarm from the video output port or alarm output connector when the camera completes a move to a preset position. An
alarm is output in the following cases.
•When the self return function is activated (page 33) and the camera finishes moving to the home position, and when switching to the auto mode.
•When SEQ is selected for the auto mode (page 33), and the camera completes a move to a preset position during sequential movement
•When SORT is selected for the auto mode (page 33), and the camera completes a move to a preset position during SORT movement
•When AUTO PAN is selected for the auto mode (page 33), and the camera completes a preset move up to the AUTO PAN start point
•When the camera completes a move to a preset position during manual operation
•When PLAY is selected for the PATROL mode (page 35), and the camera completes a preset move up to the patrol start point
Use the following procedures to configure preset alarm settings
1. Move the cursor to PRESET ALM, and then tilt the joystick left or right to toggle it on and off.
ON : Turns on the preset alarm function.
OFF : Turns off the preset alarm function.
Note: Turn off the preset alarm function before downloading or uploading preset data.
(3) Alarm Input/Output (ALARM IN/OUT)
Use this setting to specify what operation the camera should perform when it an alarm signal is input to the alarm input connector or output from the alarm output connector.
Note: While the camera is in the AF mode or the lens moves between WIDE and TELE, alarm input may be ignored if several alarm inputs are received in succession.
1.Move the cursor to the ALARM IN/OUT O and then press the CAM (SET) button.
This will display the alarm setting menu.
2.Move the cursor to ALARM IN 1, and then tilt the joystick left and right to select the operation the
camera should perform when an external signal is received by ALARM IN 1.
OFF | : Ignore alarm input signals. |
1POSI | : Move to preset position 1. |
AUTOPAN | : Start auto pan. |
PATROL1 | : Start PATROL 1. |
PATROL1 (S) : Start PATROL 1, and maintain the stored picture quality settings (page 35) even after completion.
AUTOTRACK1 : Move to preset position number 1, and then perform auto tracking.
**ALARM IN/OUT**
ALARM IN1 | OFF |
|
ALARM IN2 | OFF |
|
ALARM IN3 | OFF | |
ALARM IN4 | OFF | |
OFF | ||
TIME OUT | 100MS | |
OFF | ||
COAX ALM OUT | OFF | |
RET TOP |
|
|