Kenwood KDC-516S, KDC-57MR Security Code, If you press the Reset button or remove the battery

Page 28

Menu settings

English

Security Code

When the battery is removed from the unit's power switch, you cannot turn on the unit again unless the preset security code is input. This function helps prevent theft.

NOTE

You must follow steps 1 to 8 to be able to use the Security Code function. Turning off the power during the procedure will deactivate the security code setting.

Once the security code function has been activated, "Security" disappears from the MENU system. Note that it will no longer be possible to cancel this function afterwards.

1Press the SRC button repeatedly to select the standby mode. "ALL OFF" is displayed when the standby mode is selected.

2Select the four digits to use in your security code.

NOTE

The four-digit security code is very important, as you will need it to turn the unit on again when the code security function is on. Choose the number carefully and do not forget it (write it down and keep it separately in a safe place).

3Press the MENU button for at least one second.

"MENU" is displayed first and then "Security" is displayed.

4Press either the 4 or ¢ button for at least two seconds. "ENTER" will appear in the display for one second, indicating the code setting mode has been entered. When "CODE" appears in the display, you can start inputting the code.

5Press the preset button and enter the security code that you have selected in step 2.

Example: Use "3510" as the security code.

Step

Button to press

# Times

Display

pressed

 

 

 

1

#1

4

“3”

2

#2

6

“5”

3

#3

2

“1”

4

#4

1

“0”

6Press the DISP button for at least three seconds. The security code will be set.

"RE-ENTER" will appear in the display for one second, asking you to enter the code once again for confirmation. When "CODE" appears in the display, you can start inputting the code.

7Press the Preset button and input the security code again.

8Press the DISP button again for at least three seconds. "APPROVED" will appear in the display, with the security code function turning on. From this point on, if the unit is disconnected from the battery, the security code must be entered the first time that the unit's power is turned on. "ENTER" and "CODE" will appear in the display, asking you to input the code.

NOTE

If you input an incorrect security code, the code setting mode will be canceled automatically. Follow the steps from 4 to 8 above again.

If you press the RESET button or remove the battery:

The first time you turn the unit on again, "CODE" will appear in the display, asking you to input the security code.

Repeat steps 7 and 8 above, and input the security code. You can start operating the unit again when "APPROVED" appears in the display.

If you enter the incorrect code, the power will turn off. Enter the correct code to turn the unit on.

— 28 —

Page 27 Page 29
Image 28
Page 27 Page 29
Contents KDC-X617 KDC-V6017 KDC-516S KDC-57MR Contents 2Warning Safety precautions To prevent injury or fire, take the following precautionsCleaning the CD Slot Cleaning the Faceplate TerminalsCleaning the Unit Lens FoggingCleaning CDs Handling Compact discsStoring CDs Checking New CDs for BurrsDo Not Load CD Accessories Removing the CDDo Not Use Special Shape CDs Do Not Use CDs with Sticker on the Labeled SidePower General featuresSwitching Modes Volume AttenuatorLoudness Non-Fading OutputTheft Deterrent Faceplate Removing the FaceplateReattaching the Faceplate Hiding the control panelSwitching the Preset Sound Setting Speaker & Woofer settingSystem Q Clock display Audio control featuresChanging the Clock Display Audio Control Setting Bass Center FrequencyBass Level Bass Quality FactorMiddle Center Frequency Treble LevelMiddle Level Middle Quality FactorPhase for Non-Fading Output Volume OffsetHigh-pass Filter Frequency for Front Output High-pass Filter Frequency for Rear OutputTuner features TuningSelecting Tuning Mode TuningStation Preset Memory Canceling Direct Access TuningRecalling a Preset Station Auto Memory EntryStation Name Preset Snps Switching Display for TunerAssigning Names Changing the DisplayCD/External disc control features Playing Other Disc mode Playing CDsFast Forwarding and Reversing Disc Play Switching Display for DiscsTrack Search Track / Disc Repeat Track ScanRandom Play To scroll automatically Text / Title ScrollTo scroll manually Presetting Disc Names Dnps To cancel Dnpp mode Press the Dnpp button Disc Name Preset Play DnppRapid display forward / reverse Menu settings Canceling Direct Disc Search While It Is OperatingEnter the menu mode Ending the menu mode Press the Menu buttonMenu System Selecting function to setIf you press the Reset button or remove the battery Security CodeManual Time Adjustment Switching Graphic DisplayTouch Sensor Tone Selectable IlluminationContrast Adjustment Variable Illumination Color SettingDimmer Text Scroll In External disc control mode External Amp ControlBasic Operations of remote Loading and Replacing the BatteriesTuner features Basic operationsCD/External disc control features Accessories Installation ProcedureConnecting Wires to Terminals ACCInstallation Installing in Japanese-Made CarsRemoving the hard rubber frame Removing the UnitPage Troubleshooting Guide Problem Possible Cause SolutionProblem Possible Cause Solution CD/External disc control mode No Panel Specifications FM tuner sectionAM tuner section Audio section CD player sectionPage RiiGGiq Warranty Card WHO is Protected KDC-X617 Page Excelon Kenwood
Top Page Image Contents