Axis Communications P3384-V Linux/Unix syntax, Linux/Unix example, Axis Video Hosting System Avhs

Page 48

AXIS P3384–V Fixed Dome Network Camera

System Options

1.Acquire a free static IP address on the same network segment as the computer.

2.Locate the serial number (S/N) on the product label.

3.Open a command prompt and enter the following commands:

Linux/Unix syntax

arp -s <IP address> <serial number> temp ping -s 408 <IP address>

Linux/Unix example

arp -s 192.168.0.125 00:40:8c:18:10:00 temp ping -s 408 192.168.0.125

Windows syntax (this may require that you run the command prompt as an administrator)

arp -s <IP address> <serial number> ping -l 408 -t <IP address>

Windows example (this may require that you run the command prompt as an administrator)

arp -s 192.168.0.125 00-40-8c-18-10-00 ping -l 408 -t 192.168.0.125

4.Check that the network cable is connected and then restart the product by disconnecting and reconnecting power.

5.Close the command prompt when the product responds with Reply from 192.168.0.125:... or similar.

6.Open a browser and type http://<IP address> in the Location/Address field.

For other methods of assigning the IP address, see the Installation and Management Software CD or the document Assign an IP Address and Access the Video Stream on Axis Support web at www.axis.com/techsup

Note

•To open a command prompt in Windows, open the Start menu and type cmd in the Run/Search field.

•To use the ARP command in Windows 8/Windows 7/Windows Vista, right-click the command prompt icon and select Run as administrator.

•To open a command prompt in Mac OS X, open the Terminal utility from Application > Utilities.

AXIS Video Hosting System (AVHS)

AVHS used in conjunction with an AVHS service, provides easy and secure Internet access to live and recorded video accessible from any location. For more information and help to find a local AVHS Service Provider go to www.axis.com/hosting

The AVHS settings are configured under System Options > Network > TCP IP > Basic. The possibility to connect to an AVHS service is enabled by default. To disable, clear the Enable AVHS box.

One-click enabled - Press and hold the product’s control button (see Hardware Overview on page 6 ) for about 3 seconds to connect to an AVHS service over the Internet. Once registered, Always will be enabled and the Axis product stays connected to the AVHS service. If the product is not registered within 24 hours from when the button is pressed, the product will disconnect from the AVHS service.

Always - The Axis product will constantly attempt to connect to the AVHS service over the Internet. Once registered the product will stay connected to the service. This option can be used when the product is already installed and it is not convenient to use the one-click installation.

AXIS Internet Dynamic DNS Service

AXIS Internet Dynamic DNS Service assigns a host name for easy access to the product. For more information, see www.axiscam.net

48

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Axis P3384-V Fixed Dome Network Camera About this Document Legal ConsiderationsLiability Intellectual Property RightsSupport Learn MoreTable of Contents Axis P3384-V Fixed Dome Network CameraReset to Factory Default Settings Connectors Performance ConsiderationsConnectors and Buttons Network ConnectorConnector Hardware OverviewLED Indicators Audio ConnectorSD Card Slot Control ButtonAccess the Product Access from a BrowserAccess from the Internet Set the Root PasswordSet Power Line Frequency Live ViewControls on the Live View Click Use HttpsGo to Setup Events Axis Media Control viewer toolbarManual Trigger To show the manual trigger buttons in the Live ViewPTZ Controls AMC Audio ControlsAxis P3384-V Fixed Dome Network Camera How to Stream H.264 Media StreamsAxis Media Control AMC Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAccess Audio Streams Java applet supports simplex audio with G.711 encodingSet Up the Product Basic SetupClick Save to apply the new settings Video and AudioVideo Stream ImageStream Profiles MjpegCamera Settings Lightfinder ModeImage Appearance White BalanceExposure Settings Iris adjustmentShutter & Gain Set Shutter toSelect an Aspect ratio and a Video stream resolution View AreaOverlay Go to Video & Audio View AreaPrivacy Mask Overlay ImageGo to Video & Audio Overlay Image Audio Settings When satisfied, click Enable iris to enable the irisFocus & Zoom Audio ModesAudio Input Audio OutputAudio Clips Configure the Live View Default Viewer for BrowsersViewer Settings Browser Viewer DescriptionGo to Setup Live View Config User Defined LinksOutput Buttons For more information about I/O ports, see I/O Ports onPreset Positions PTZ Pan Tilt ZoomGuard Tour AdvancedOperator Same as administrator but with lower priority Control QueueDetectors Camera TamperingMotion Detection Go to Detectors Camera TamperingSet Up Motion Detection Windows Motion Detection ParametersAudio Detection Go to Detectors Audio DetectionInstall Application Go to Setup ApplicationsApplications Application LicensesAxis P3384-V Fixed Dome Network Camera Set Up Action Rules EventsTriggers Go to Events Action Rules and click AddInput Signal HardwareStorage SystemAdd Recipients ActionsRecipient Types PTZ ControlSet Up Email Recipients Create SchedulesRecipient Use with action Set Up Recurrences Go to Events Schedules and click AddGo to Events Recurrences and click Add Recordings Find RecordingsPlay Recording Go to Recordings ListExport Video Clip Recording ListContinuous Recording Go to Recordings ContinuousLanguages System Options SecurityUsers IP Address FilterIeee CertificatesCA Certificate Go to Setup System Options Security Certificates Click Install certificate and upload the certificateDate & Time CertificatesBasic TCP/IP Settings NetworkAxis Internet Dynamic DNS Service Linux/Unix syntaxLinux/Unix example Axis Video Hosting System AvhsAdvanced TCP/IP Settings DNS ConfigurationNTP Configuration Host Name ConfigurationHttps NAT traversal port mapping for IPv4QoS Quality of Service SocksStorage UPnPTMRTP/H.264 BonjourNetwork Share Mount and Unmount SD CardFormat SD Card To add a network shareMaintenance Ports & DevicesPorts Port StatusSupport Support OverviewSystem Overview Logs & ReportsReset to Factory Default Settings Plain ConfigFile Upload Troubleshooting Upgrade the FirmwareFirmware To upgrade the product’s firmware Check the FirmwareEmergency Recovery Procedure Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserProduct is accessible locally but not externally Problems with streaming H.264Basic Status and Network indicator LEDs are flashing red rapidly Video and image problems, generalSetup Video & Audio Camera Settings SettingsVideo cannot be recorded Technical Specifications Function/group Specifications Network Security InstallationMaintenance SupportedFunction/group Specifications General Casing PowerConnectors DimensionsConnectors Function Pin SpecificationsPerformance Considerations Audio InputAudio Output M2.13
Top Page Image Contents