Axis Communications P3384-V user manual Socks, QoS Quality of Service

Page 51

AXIS P3384–V Fixed Dome Network Camera

System Options

SOCKS

SOCKS is a networking proxy protocol. The Axis product can be configured to use a SOCKS server to reach networks on the other side of a firewall or proxy server. This functionality is useful if the Axis product is located on a local network behind a firewall, and notifications, uploads, alarms, etc need to be sent to a destination outside the local network (for example the Internet).

SOCKS is configured under System Options > Network > SOCKS. For more information, see the online help .

QoS (Quality of Service)

QoS (Quality of Service) guarantees a certain level of a specified resource to selected traffic on a network. A QoS-aware network prioritizes network traffic and provides a greater network reliability by controlling the amount of bandwidth an application may use.

The QoS settings are configured under System Options > Network > QoS. Using DSCP (Differentiated Services Codepoint) values, the Axis product can mark different types of traffic.

Note

Live audio DSCP will be equal to live video DSCP if H.264 over RTSP is used.

SNMP

The Simple Network Management Protocol (SNMP) allows remote management of network devices. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups.

AXIS Video MIB (Management Information Base) for video hardware can be used to monitor Axis-specific, hardware-related issues that may need administrative attention. For more information about AXIS Video MIB and to download MIB files, go to www.axis.com/techsup

To enable and configure SNMP in the Axis product, go to the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

Note

All AXIS Video MIB traps are enabled when SNMP v1/v2c traps are enabled. It is not possible to turn on or off specific traps.

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 44. To enable SNMP v3, check the box and provide the initial user password.

51

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Axis P3384-V Fixed Dome Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis P3384-V Fixed Dome Network Camera Table of ContentsConnectors Performance Considerations Reset to Factory Default SettingsHardware Overview Connectors and ButtonsNetwork Connector ConnectorControl Button LED IndicatorsAudio Connector SD Card SlotSet the Root Password Access the ProductAccess from a Browser Access from the InternetClick Use Https Set Power Line FrequencyLive View Controls on the Live ViewTo show the manual trigger buttons in the Live View Go to Setup EventsAxis Media Control viewer toolbar Manual TriggerAMC Audio Controls PTZ ControlsAxis P3384-V Fixed Dome Network Camera How to Stream H.264 Media StreamsAxis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Access Audio StreamsBasic Setup Set Up the ProductImage Click Save to apply the new settingsVideo and Audio Video StreamMjpeg Stream ProfilesWhite Balance Camera SettingsLightfinder Mode Image AppearanceSet Shutter to Exposure SettingsIris adjustment Shutter & GainGo to Video & Audio View Area Select an Aspect ratio and a Video stream resolutionView Area OverlayPrivacy Mask Overlay ImageGo to Video & Audio Overlay Image Audio Modes Audio SettingsWhen satisfied, click Enable iris to enable the iris Focus & ZoomAudio Output Audio InputAudio Clips Browser Viewer Description Configure the Live ViewDefault Viewer for Browsers Viewer SettingsFor more information about I/O ports, see I/O Ports on Go to Setup Live View ConfigUser Defined Links Output ButtonsAdvanced Preset PositionsPTZ Pan Tilt Zoom Guard TourControl Queue Operator Same as administrator but with lower priorityGo to Detectors Camera Tampering DetectorsCamera Tampering Motion DetectionMotion Detection Parameters Set Up Motion Detection WindowsGo to Detectors Audio Detection Audio DetectionApplication Licenses Install ApplicationGo to Setup Applications ApplicationsAxis P3384-V Fixed Dome Network Camera Go to Events Action Rules and click Add Set Up Action RulesEvents TriggersSystem Input SignalHardware StoragePTZ Control Add RecipientsActions Recipient TypesSet Up Email Recipients Create SchedulesRecipient Use with action Set Up Recurrences Go to Events Schedules and click AddGo to Events Recurrences and click Add Go to Recordings List RecordingsFind Recordings Play RecordingRecording List Export Video ClipGo to Recordings Continuous Continuous RecordingLanguages IP Address Filter System OptionsSecurity UsersIeee CertificatesCA Certificate Certificates Go to Setup System Options Security CertificatesClick Install certificate and upload the certificate Date & TimeNetwork Basic TCP/IP Settings Axis Video Hosting System Avhs Axis Internet Dynamic DNS Service Linux/Unix syntax Linux/Unix exampleHost Name Configuration Advanced TCP/IP SettingsDNS Configuration NTP ConfigurationNAT traversal port mapping for IPv4 HttpsSocks QoS Quality of ServiceBonjour StorageUPnPTM RTP/H.264To add a network share Network ShareMount and Unmount SD Card Format SD CardPort Status MaintenancePorts & Devices PortsLogs & Reports SupportSupport Overview System OverviewReset to Factory Default Settings Plain ConfigFile Upload Check the Firmware TroubleshootingUpgrade the Firmware Firmware To upgrade the product’s firmwareProduct cannot be accessed from a browser Emergency Recovery ProcedureSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct is accessible locally but not externally Problems with streaming H.264Basic Settings Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Setup Video & Audio Camera SettingsVideo cannot be recorded Technical Specifications Supported Function/group Specifications Network SecurityInstallation MaintenanceDimensions Function/group Specifications General CasingPower ConnectorsFunction Pin Specifications ConnectorsPerformance Considerations Audio InputAudio Output M2.13
Top Page Image Contents