Axis Communications M5013 user manual Storage, UPnPTM, RTP/H.264, Bonjour, SD Card

Page 38

AXIS M5013 PTZ Dome Network Camera

System Options

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS, on page 32. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to factory default settings, on page 41.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video and/or Always Multicast Audio to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD Card

The SD/SDHC memory card (not included) is managed on the System Options > Storage > SD Card page.

The settings under Storage Device are used to identify and monitor the status of the SD card, and to unmount the SD card before removal. Mounting is done automatically when a card is inserted. SD cards are normally preformatted when purchased, but if needed, click Format to format the card.

Note

To prevent corruption of recordings, the SD card should always be unmounted before removal.

If the card’s status shows as failed, click Check disk to see if the problem can be found and then try Repair.

The settings under Storage Device Settings are used to configure removal of recorded video. Automatic disk cleanup can be enabled and set according to a schedule. The disk can be locked to prevent removal of recordings.

38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Axis M5013 PTZ Dome Network Camera Intellectual Property Rights About this documentLiability Equipment ModificationsTable of Contents Axis M5013 PTZ Dome Network CameraHardware overview ConnectorsHardware overview Color Indication LED indicatorsMaintenance Access from a browser Accessing the productAccessing the product Network TCP/IP Advanced Access from the InternetSet the root password Click Create self-signed certificateSet Power Line Frequency Live ViewPTZ Controls Controls on the Live ViewAxis Media Control viewer toolbar AMC Audio controlsAxis M5013 PTZ Dome Network Camera Media streams How to stream H.264Media streams Axis Media Control AMCAlternative methods of accessing the video stream Accessing audio streams Basic Setup Setting up the productSetting up the product Video Stream Video and AudioVideo and Audio Pixel CounterImage Camera SettingsStream Profiles 264Audio Settings OverlayG711 G726 Live View Config Default viewer for browsersLive View Config Browser Viewer DescriptionViewer Settings User Defined LinksPTZ Pan Tilt Zoom Preset PositionsPTZ Pan Tilt Zoom Osdi ZonesLimits AdvancedControl Queue ControlsDetectors Set up motion detectionDetectors Motion DetectionAudio detection Applications ApplicationsEvents EventsGo to Events Action Rules and click Add Setting Up an Action RuleConvert Event Types to Action Rules Recurrences RecipientsSchedules Axis M5013 PTZ Dome Network Camera Recording List RecordingsRecordings Continuous recordingAxis M5013 PTZ Dome Network Camera Security System OptionsSystem Options UsersAudio Support Date & TimeIeee IPv4 Address Configuration Basic TCP/IP SettingsNetwork IPv6 Address ConfigurationAdvanced TCP/IP Settings Link-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service Smtp emailRTP/H.264 StorageUPnPTM BonjourGo to System Options Storage Click Network Share MaintenanceNetwork Share System Overview SupportSupport Overview Logs & ReportsPlain Config Reset to factory default settingsFile Upload Emergency recovery procedure TroubleshootingTroubleshooting Checking the firmwareProduct cannot be accessed from a browser Symptoms, possible causes and remedial actionsProblems setting the IP address Product is accessible locally but not externally Problems with the H.264 formatProblems uploading files Video and image problems, generalSetup Video & Audio Camera Settings No images displayed on webStorage and disk management problems Technical Specifications Technical SpecificationsMaintenance General Casing Alarm triggersInstallation PowerPerformance considerations M3.3
Top Page Image Contents