Panasonic WV-NW964 Unicast port1 Image, Default Unicast port2 Audio, Default Multicast address

Page 22

When it is unnecessary to fix the port number for MPEG-4 image transmission such as when using in a particular LAN environment, it is recommended to select "Unicast port (AUTO)".

Unicast port (MANUAL): Up to 8 users can access a single camera concurrently. It is necessary to select "Unicast port1 (Image)" and "Unicast port2 (Audio)" manually to transmit images and audio from the camera.

It is possible to fix the port number of the router used for MPEG-4 image transmission via the Internet by setting "Unicast port (MANUAL)". (page 76) Refer to the operating instructions of the router in use.

Multicast: No concurrent access limitation for a cam- era.

Refer to Operation Instructions for further information about the maximum concurrent access number. Default: Unicast port (AUTO)

[Unicast port1 (Image)]

Enter the unicast port number (used to transmit images from the camera).

Available port number: 1024 - 50000 (Only even num- bers are available.)

Default: 32004

[Unicast port2 (Audio)]

Enter the unicast port number (used to transmit audio from the camera).

Available port number: 1024 - 50000 (Only even num- bers are available.)

Default: 33004

[Multicast address]

Enter the multicast IP address.

Images and audio will be transmitted to the designated IP address.

Available IP address: 224.0.0.0 - 239.255.255.255

Default: 239.192.0.20

[Multicast port]

Enter the multicast port number (used to transmit images from the camera).

Available port number: 1024 - 50000 (Only even num- bers are available.)

Default: 37004

[Multicast TTL]

Enter the multicast TTL value.

Available value: 1 - 254

Default: 16

Important:

Depending on the PC in use for monitoring, the mul- ticast port number may be already in use. In this case, it may be impossible to monitor images. Change the multicast port number.

When transmitting an MPEG-4 image via a network, the transmitted image sometimes may not be dis- played. In this case, refer to the network administra- tor.

When two or more network interface cards are installed on the PC in use, the network interface card(s) not used for receiving images should be invalidated when displaying images using the multi- cast port.

22

Image 22
Contents WV-NW964 Contents Trademarks and registered trademarks About these operating instructionsViewer software How to display the setup menu StepHow to operate the setup menu About the setup menu window Maintenance button Network setup buttonSchedule setup button 3SetupConfigure the basic settings of the camera Basic setup Configure the basic settings BasicAlarm status port Alarm status update modeDefault Real time Default onConfigure the settings relating to the NTP server NTP SD memory card setup SD memory card information Page Step Image capture size VGA Image capture size QvgaFTP error Configure the settings relating to the logs LOGAlarm ManualOFF LOG tab SD memory card tab Logs and associated images SD memory Save trigger Overwrite Save logs CardSD memory Save logs CardDefault 5 fps Jpeg setupDefault VGA Image quality Refresh interval JpegMPEG-4 setup Default Multicast TTL Default Unicast port2 AudioDefault Multicast address Available value 1 DefaultCamera title on screen Default OFF Camera title on screen 0-9, A-ZDefault 1 min Image Hold Home positionPan·Tilt degree/Zoom ratio display StabilizerTilt Angle Auto Pan Image AdjustPreset Position PatrolSuper Dynamic About SUPER-D 3 Super Dynamic functionBlack & white mode Default AutoDefault on High Sensitivity up Default High Wait timeRed Gain Default ATW1Default High Chroma gain level Blue GainSet mask areas Register the preset position Edit the settings of the registered preset positionPosition No Position Auto panNumber of patrol pattern GO buttonLearn patrol pattern Mode Zone settingPrivacy zone Zone selectDefault 32 kbps Configure the settings relating to audio AudioAudio mode Audio bit rateDefault 40 msec Mic input volume Camera to PCDefault Middle Mic input interval Camera to PC Audio output volume PC to CameraIP address Configures the multi-screen settings Multi-screen setupNumber of characters for the IP address 1 Configure the settings relating to the alarm Alarm Configure the alarm settings Alarm setupAlarm setup Command alarm Originating port number Camera motion on alarmAvailable port number 1 Alarm image setup Configure the settings relating to the alarm imageDefault OFF Command alarm Post alarm Transmission interval To FTP setupAlarm image FTP transmission Default 1 fps Number of imagesAlarm output terminal setup Configure the settings relating to the alarm out terminalAUX name Set the VMD areas VMD area Default OFF Detection sensitivity StatusSet the VMD areas for each preset position Delete the VMD area set for the designated preset position Default MiddleMail notification setup Panasonic alarm protocol setup Configure the settings relating to Panasonic alarm protocolPanasonic alarm protocol Password Retype password User authenticationDefault OFF User name Number of characters for the password 4 32 charHost authentication Default OFF Access levelConfigure the settings of the servers Server setup Configure the settings relating to the mail server MailConfigure the settings relating to the FTP server FTP Configure the network settings Network Configuring the network settings Network setupNetwork setup Available port number 1 Default Port numbers already in use Default gatewayUnavailable IP addresses for the default gate- way Default Manual Primary DNS, Secondary DNSWAN Default OFF Host name Configure the settings relating to Ddns DdnsAccess interval Number of characters for the host name 1 64 charConfigure the settings relating to Snmp Snmp FTP periodic transmission Default OFF DirectoryFTP periodic transmission Number of characters for the directory name 1How to configure the schedule settings Schedule setupInterval How to delete the set schedule How to set the schedules Check the system log System log Maintenance of the camera MaintenanceError message Time & dateUpgrade the firmware Upgrade How to upgrade the firmwareInitialize Html data Initialize setup data and Html dataInitialize/restart the camera Initialization RestartDisplaying the Help screen Setup screen StepHelp screen Step Error indications relating to FTP Error indications relating to SmtpCategory Indication Description Error indications relating to NTP Error indications relating to DdnsError indications relating to login Troubleshooting Symptom Installation Guide Cause/solution Reference Pages Installation Guide Operation Instructions Symptom Solutions Reference Pages Directory structure of drive B Group LAN IP address LAN port WAN IP address Protocol Group WAN IP address Protocol LAN IP address LAN portN0907-0 3TR005323AAB
Related manuals
Manual 21 pages 50.64 Kb

WV-NW964, WV-NS954 specifications

The Panasonic WV-NW964 and WV-NS954 are advanced network cameras designed for high-performance surveillance in various applications. Both models offer a remarkable combination of features, technologies, and characteristics that make them ideal for security monitoring in both indoor and outdoor environments.

The WV-NW964 is a high-definition network camera equipped with a 1/3-inch progressive scan CCD sensor, delivering exceptional image quality with resolutions up to 1280x960 pixels. It is particularly well-suited for situations where clarity and detail are paramount, such as in retail spaces or critical infrastructure facilities. The camera supports H.264 compression technology, which allows for efficient video streaming while maintaining high image quality. This feature is particularly useful for reducing bandwidth requirements and storage costs without compromising surveillance effectiveness.

On the other hand, the WV-NS954 is a PTZ (pan-tilt-zoom) network camera that provides extensive flexibility in monitoring wide areas. With its 3x optical zoom lens, it enables users to focus on specific subjects or areas of interest without loss of detail. The camera's ability to pan 360 degrees and tilt up to 90 degrees allows for comprehensive coverage of large spaces, making it ideal for applications such as parking lots, open-air venues, and warehouses.

Both cameras are equipped with advanced features such as digital noise reduction and wide dynamic range (WDR) technology, ensuring clear images in varying lighting conditions. The WDR feature is particularly beneficial in scenarios where backlighting can obscure details, allowing for better visibility of individuals or objects even in challenging environments. Additionally, the cameras support multiple streaming formats and resolutions, providing flexibility in how video feeds are accessed and managed across different network systems.

With built-in motion detection and event-triggered recording capabilities, both cameras enhance security by providing alerts when unusual activity is detected. Users can customize alert settings based on specific needs, ensuring efficient and timely response to potential security threats. Furthermore, both models are designed with robust IP66-rated weatherproofing, making them suitable for outdoor deployment in various weather conditions without the risk of damage.

In summary, the Panasonic WV-NW964 and WV-NS954 network cameras deliver outstanding performance through their advanced imaging technologies and versatile functionalities. With features tailored for high-quality surveillance, efficient data management, and user-friendly operation, they are essential tools for enhancing security in a variety of applications.